From: gregory.clement@free-electrons•com (Gregory CLEMENT)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH 01/16] dt-bindings: mvebu-uart: update documentation with extended UART
Date: Fri, 06 Oct 2017 14:17:28 +0200 [thread overview]
Message-ID: <87376wh3mv.fsf@free-electrons.com> (raw)
In-Reply-To: <20171006101344.15590-2-miquel.raynal@free-electrons.com> (Miquel Raynal's message of "Fri, 6 Oct 2017 12:13:29 +0200")
Hi Miquel,
On ven., oct. 06 2017, Miquel Raynal <miquel.raynal@free-electrons•com> wrote:
> Update the Device Tree binding documentation for the Marvell EBU UART,
> in order to allow describing the extended UART IP block, in addition to
> the already supported standard UART IP. This requires adding a new
> compatible string, the introduction of a clocks property, and extensions
> to the interrupts property.
>
> Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons•com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons•com>
Thanks,
Gregory
> ---
> .../devicetree/bindings/serial/mvebu-uart.txt | 49 +++++++++++++++++++---
> 1 file changed, 44 insertions(+), 5 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt
> index d37fabe17bd1..3df3a3fab4bb 100644
> --- a/Documentation/devicetree/bindings/serial/mvebu-uart.txt
> +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt
> @@ -1,13 +1,52 @@
> -* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g., Armada-3700)
> +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs
> + e.g., Armada-3700.
>
> Required properties:
> -- compatible: "marvell,armada-3700-uart"
> +- compatible:
> + - "marvell,armada-3700-uart" for the standard variant of the UART
> + (32 bytes FIFO, no DMA, level interrupts, 8-bit access to the
> + FIFO, baudrate limited to 230400).
> + - "marvell,armada-3700-uart-ext" for the extended variant of the
> + UART (128 bytes FIFO, DMA, front interrupts, 8-bit or 32-bit
> + accesses to the FIFO, baudrate unlimited by the dividers).
> - reg: offset and length of the register set for the device.
> -- interrupts: device interrupt
> +- clocks: UART reference clock used to derive the baudrate (only
> + mandatory with "marvell,armada-3700-uart-ext" compatible).
> +- interrupts:
> + - Must contain three elements for the standard variant of the IP
> + (marvell,armada-3700-uart): "uart-sum", "uart-tx" and "uart-rx",
> + respectively the UART sum interrupt, the UART TX interrupt and
> + UART RX interrupt. A corresponding interrupt-names property must
> + be defined.
> + - Must contain two elements for the extended variant of the IP
> + (marvell,armada-3700-uart-ext): "uart-tx" and "uart-rx",
> + respectively the UART TX interrupt and the UART RX interrupt. A
> + corresponding interrupts-names property must be defined.
> + - For backward compatibility reasons, a single element interrupts
> + property is also supported for the standard variant of the IP,
> + containing only the UART sum interrupt. This form is deprecated
> + and should no longer be used.
>
> Example:
> - serial at 12000 {
> + uart0: serial at 12000 {
> compatible = "marvell,armada-3700-uart";
> reg = <0x12000 0x200>;
> - interrupts = <43>;
> + clocks = <&xtalclk>;
> + interrupts =
> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "uart-sum", "uart-tx", "uart-rx";
> + status = "disabled";
> + };
> +
> + uart1: serial at 12200 {
> + compatible = "marvell,armada-3700-uart-ext";
> + reg = <0x12200 0x30>;
> + clocks = <&xtalclk>;
> + interrupts =
> + <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "uart-tx", "uart-rx";
> + status = "disabled";
> };
> --
> 2.11.0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
next prev parent reply other threads:[~2017-10-06 12:17 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-10-06 10:13 [PATCH 00/16] Support armada-37xx second UART port Miquel Raynal
2017-10-06 10:13 ` [PATCH 01/16] dt-bindings: mvebu-uart: update documentation with extended UART Miquel Raynal
2017-10-06 12:17 ` Gregory CLEMENT [this message]
2017-10-06 10:13 ` [PATCH 02/16] pinctrl: dt-bindings: Fix A37xx uart2 group name Miquel Raynal
2017-10-06 12:18 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 03/16] serial: mvebu-uart: use driver name when requesting an interrupt Miquel Raynal
2017-10-06 12:19 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 04/16] serial: mvebu-uart: support probe of multiple ports Miquel Raynal
2017-10-06 12:23 ` Gregory CLEMENT
2017-10-09 7:17 ` Miquel RAYNAL
2017-10-12 12:22 ` Gregory CLEMENT
2017-10-13 7:29 ` Miquel RAYNAL
2017-10-06 10:13 ` [PATCH 05/16] serial: mvebu-uart: use a generic way to access the registers Miquel Raynal
2017-10-06 12:32 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 06/16] serial: mvebu-uart: add soft reset at probe Miquel Raynal
2017-10-06 12:33 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 07/16] serial: mvebu-uart: add function to change baudrate Miquel Raynal
2017-10-06 12:39 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 08/16] serial: mvebu-uart: clear state register before IRQ request Miquel Raynal
2017-10-06 12:40 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 09/16] serial: mvebu-uart: add TX interrupt trigger for pulse interrupts Miquel Raynal
2017-10-06 20:22 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 10/16] serial: mvebu-uart: dissociate RX and TX interrupts Miquel Raynal
2017-10-06 13:11 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 11/16] serial: mvebu-uart: augment the maximum number of ports Miquel Raynal
2017-10-06 12:45 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 12/16] serial: mvebu-uart: support extended port registers layout Miquel Raynal
2017-10-06 12:46 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 13/16] arm64: dts: marvell: armada-37xx: add UART clock Miquel Raynal
2017-10-06 12:48 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 14/16] arm64: dts: marvell: armada-37xx: add second UART port Miquel Raynal
2017-10-06 12:49 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 15/16] arm64: dts: marvell: armada-3720-db: enable " Miquel Raynal
2017-10-06 12:51 ` Gregory CLEMENT
2017-10-06 10:13 ` [PATCH 16/16] arm64: dts: marvell: armada-3720-espressobin: fill UART nodes Miquel Raynal
2017-10-06 13:01 ` Gregory CLEMENT
2017-10-06 13:15 ` Thomas Petazzoni
2017-10-09 7:30 ` Miquel RAYNAL
2017-10-12 11:24 ` Gregory CLEMENT
2017-10-13 7:01 ` Miquel RAYNAL
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87376wh3mv.fsf@free-electrons.com \
--to=gregory.clement@free-electrons$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox