Subject: Re: kernel panic when get ip through BOOTP!

From: "SangTae Ha" <[email-masked]>
Date: Thu, 26 Apr 2001 17:59:36 +0900

Maybe, your tcp/ip stack works properly but your physical ethernet interface doesn't.
Check your port mapping in arch/ppc/mbxboot/commproc.h.

-----------------------------------------------------------
#define PB_ENET1_RXD    ((uint)0x00000004
#define PB_ENET1_TXD    ((uint)0x00000002
...
...
...
...
..
..
..
------------------------------------------------------------
Thank you.

----- Original Message -----
From: <[email-masked]>
To: <[email-masked]>
Sent: Thursday, April 26, 2001 4:42 PM
Subject: kernel panic when get ip through BOOTP!

>
> hello all,
> when i down hhl 2.2.14 to ram via tftp,then run from 0x200000.when kernel try to send bootp requests to network ,it always told me time out.
> my host's DHCPD service is working(i even reinstall my linux again!),but not use.Is this stituation about the ethenet driver? if it is ,then should i do?
>
> here is my output form minicom.cap;
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>
>
> pSOSystem V2.5.0
> Copyright (c) 1991 - 1998, Integrated Systems, Inc.
> --------------------------------------------------------------------------
> START-UP MODE:
>   Boot into pROBE+ and wait for host debugger via a network connection
> NETWORK INTERFACE PARAMETERS:
>   IP address on LAN is 192.168.6.165
>   LAN interface's subnet mask is 0xffffff00
> HARDWARE PARAMETERS:
>   Serial channels will use a baud rate of 9600
> HARDWARE PARAMETERS:
>   Processor     : MPC850 (Rev E.1), Running at 48Mhz
>   Board Info    : MAXRIX Board (Rev-R)
>   Board memory  : FLASH : 4Mbytes, 60ns, Enabled
>                   DRAMs : 8Mbytes, 70ns, Enabled, EDO
>   Board's Ethernet hardware address : 08:00:3E:22:33:55
>   After board is reset, start-up code will wait 10 seconds
> --------------------------------------------------------------------------
> To change any of this, press any key within 10 seconds
>
> (M)odify any of this or (C)ontinue? [M]
>
> For each of the following questions, you can press <Return> to select the
> value shown in braces, or you can enter a new value.
>
> How should the board boot?
>   1. pROBE+ stand-alone mode
>   2. pROBE+ waiting for host debugger via serial connection
>   3. pROBE+ waiting for host debugger via a network connection
>   4. Run the TFTP Bootloader
>
> Which one do you want? [3] 4
>
> If connect to host debuger, which connection to use ?
>   1. Serial Connection
>   2. Network Connection
>
> Which one do you want? [1]
>
> NETWORK INTERFACE PARAMETERS:
> Do you want a LAN interface?  [Y]
> This board's LAN IP address(0.0.0.0 = RARP)? [192.168.6.165]
> Subnet mask for LAN (0 for none)? [255.255.255.0]
> Should there be a default gateway for packet routing?  [N]
> HARDWARE PARAMETERS:
> Baud rate for serial channels [9600]
>
> HARDWARE PARAMETERS:
> Do you want to change the board's Ethernet address? [N]
> TFTP BOOTLOADER PARAMETERS:
> IP address of the TFTP Boot server to boot from? [192.168.6.191]
> Name of the file to load and start? [boot.srec]
> How long (in seconds) should CPU delay before starting up? [10]
>
> --------------------------------------------------------------------------
> START-UP MODE:
>   Run the TFTP Bootloader
> HOST DEBUGGER CONNECTION (if activated):
>   Serial channel 0x1
> NETWORK INTERFACE PARAMETERS:
>   IP address on LAN is 192.168.6.165
>   LAN interface's subnet mask is 0xffffff00
> HARDWARE PARAMETERS:
>   Serial channels will use a baud rate of 9600
> HARDWARE PARAMETERS:
>   Processor     : MPC850 (Rev E.1), Running at 48Mhz
>   Board Info    : MAXRIX Board (Rev-R)
>   Board memory  : FLASH : 4Mbytes, 60ns, Enabled
>                   DRAMs : 8Mbytes, 70ns, Enabled, EDO
>   Board's Ethernet hardware address : 08:00:3E:22:33:55
> TFTP BOOTLOADER PARAMETERS:
>   Boot via the TFTP Bootloader
>   IP address of the TFTP host is 192.168.6.191
>   The file to download and start is boot.srec
>   After board is reset, start-up code will wait 10 seconds
> --------------------------------------------------------------------------
> (M)odify any of this or (C)ontinue? [M] c
> Updating parameter storage. This may take a while...Done
>
> Downloading  "boot.srec" from HOST 192.168.6.191
> .................................
> TFTP download completed
>
> Transferring control to the downloaded code
>
>
> Unexpected Break                                   Running:  'ROOT' -#00020000
> ------------------------------------------------------------------------------
> CR =40000000 XER=00000000 LR =0000E918
> CTR=00000000 MSR=00001002
> R0 =0000E918 0005F780 0000DFF0 00000000 0018B1F8 4082005C 34091CDE 00002C7F
> R8 =02806580 00200000 00000000 001801C8 00000000 0000E918 00000000 00000000
> R16=00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> R24=000A0000 00000200 00200004 0005F794 00009D60 00000847 00000000 00000000
> IP =0000E918-0000E918: 00000000   .word     $00000000
> pROBE+> gs 200000
> HardHat Linux Kernel 2.2.14
> Borad level Porting by ZhouChang
> loaded at:     00200000 0020B1FC
> relocated to:  00180000 0018B1FC
> board data at: 001801C8 001801E4
> relocated to:  00200100 0020011C
> zimage at:     00206000 0026A245
> avail ram:     0026B000 00800000
>
> Linux/PPC load: root=/dev/nfs rw
> Uncompressing Linux...done.
> Now booting the kernel
> Linux version 2.2.14 ([email-masked]) (gcc version 2.95.2 19991030 (2.95.3 prerelease/franzo)) #21 Wed Apr 25 16:55:44 CST 2001
> Boot arguments: root=/dev/nfs rw
> time_init: decrementer frequency = 180000000/60
> Calibrating delay loop... 47.51 BogoMIPS
> Memory: 7056k available (736k kernel code, 364k data, 36k init) [c0000000,c0800000]
> Dentry hash table entries: 1024 (order 1, 8k)
> Buffer cache hash table entries: 8192 (order 3, 32k)
> Page cache hash table entries: 2048 (order 1, 8k)
> POSIX conformance testing by UNIFIX
> Linux NET4.0 for Linux 2.2
> Based upon Swansea University Computer Society NET3.039
> NET4: Unix domain sockets 1.0 for Linux NET4.0.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> TCP: Hash tables configured (ehash 8192 bhash 8192)
> Initializing RT netlink socket
> Starting kswapd v 1.5
> CPM UART driver version 0.03
> ttyS00 at 0x0280 is a SMC
> ttyS01 at 0x0380 is a SMC
> pty: 256 Unix98 ptys configured
> RAM disk driver initialized:  16 RAM disks of 4096K size
> loop: registered device at major 7
> **********enet.c stop here**************eth0: CPM ENET Version 0.2, 08:00:3e:22:33:44
> PPP: version 2.3.7 (demand dialling)
> TCP compression code copyright 1989 Regents of the University of California
> PPP line discipline registered.
> Sending BOOTP requests............eth0: transmit timed out.
>  Ring data dump: cur_tx 030028d0 (full) cur_rx 030028b8.
> 9c00 0196 0015fe02
> 9c00 0196 0015fc02
> 9c00 0196 0015fa02
> 9c00 0196 0015f602
> 9c00 0196 0015f802
> 9c00 0196 0015f402
> 9c00 0196 0015f202
> bc00 0196 0015f002
> 9c00 00ee 00166000
> 9c00 00f7 00166800
> 9c00 00e2 00165000
> 9c00 00ee 00165800
> 9c00 00f7 00164000
> 9c00 0040 00164800
> 9c00 00f7 00163000
> bc00 00e2 00163800
> eth0: tx queue full!.
> .eth0: transmit timed out.
>  Ring data dump: cur_tx 030028d0 (full) cur_rx 03002890.
> 9c00 0196 0015fe02
> 9c00 0196 0015fc02
> 9c00 0196 0015fa02
> 9c00 0196 0015f602
> 9c00 0196 0015f802
> 9c00 0196 0015f402
> 9c00 0196 0015f202
> bc00 0196 0015f002
> 9c00 00ee 00166000
> 9c00 00f7 00166800
> 9c00 00e2 00165000
> 9c00 00ee 00165800
> 9c00 00f7 00164000
> 9c00 00f7 00164800
> 9c00 0076 00163000
> bc00 0060 00163800
>
>
>

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/