From: Wolfgang Grandegger <wg@grandegger•com>
To: linux-mtd@lists•infradead.org, linuxppc-dev@ozlabs•org
Cc: devicetree-discuss@ozlabs•org
Subject: [PATCH v4 3/4] powerpc: NAND: FSL UPM: document new bindings
Date: Mon, 30 Mar 2009 12:02:44 +0200 [thread overview]
Message-ID: <20090330100555.282048633@denx.de> (raw)
In-Reply-To: 20090330100241.346785618@denx.de
This patch adds documentation for the new NAND FSL UPM bindings for:
NAND: FSL-UPM: add multi chip support
NAND: FSL-UPM: Add wait flags to support board/chip specific delays
It also documents the old binding for "chip-delay".
Signed-off-by: Wolfgang Grandegger <wg@grandegger•com>
---
Documentation/powerpc/dts-bindings/fsl/upm-nand.txt | 39 ++++++++++++++++++--
1 file changed, 37 insertions(+), 2 deletions(-)
Index: linux-2.6/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt
===================================================================
--- linux-2.6.orig/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt 2009-03-30 12:01:26.799721086 +0200
+++ linux-2.6/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt 2009-03-30 12:01:41.496969771 +0200
@@ -5,9 +5,21 @@
- reg : should specify localbus chip select and size used for the chip.
- fsl,upm-addr-offset : UPM pattern offset for the address latch.
- fsl,upm-cmd-offset : UPM pattern offset for the command latch.
-- gpios : may specify optional GPIO connected to the Ready-Not-Busy pin.
-Example:
+Optional properties:
+- fsl,upm-wait-flags : add chip-dependent short delays after running the
+ UPM pattern (0x1), after writing a data byte (0x2) or after
+ writing out a buffer (0x4).
+- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support.
+ The corresponding address lines are used to select the chip.
+- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
+ (R/B#). For multi-chip devices, "n" GPIO definitions are required
+ according to the number of chips.
+- chip-delay : chip dependent delay for transfering data from array to
+ read registers (tR). Required if property "gpios" is not used
+ (R/B# pins not connected).
+
+Examples:
upm@1,0 {
compatible = "fsl,upm-nand";
@@ -26,3 +38,26 @@
};
};
};
+
+upm@3,0 {
+ #address-cells = <0>;
+ #size-cells = <0>;
+ compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand";
+ reg = <3 0x0 0x800>;
+ fsl,upm-addr-offset = <0x10>;
+ fsl,upm-cmd-offset = <0x08>;
+ /* Multi-chip NAND device */
+ fsl,upm-addr-line-cs-offsets = <0x0 0x200>;
+ fsl,upm-wait-flags = <0x5>;
+ chip-delay = <25>; // in micro-seconds
+
+ nand@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "fs";
+ reg = <0x00000000 0x10000000>;
+ };
+ };
+};
next prev parent reply other threads:[~2009-03-30 10:05 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-03-30 10:02 [PATCH v4 0/4] NAND: Multi-chip support for FSL-UPM for TQM8548 modules Wolfgang Grandegger
2009-03-30 10:02 ` [PATCH v4 1/4] NAND: FSL-UPM: add multi chip support Wolfgang Grandegger
2009-03-31 19:05 ` Anton Vorontsov
2009-03-30 10:02 ` [PATCH v4 2/4] NAND: FSL-UPM: Add wait flags to support board/chip specific delays Wolfgang Grandegger
2009-03-31 19:05 ` Anton Vorontsov
2009-03-30 10:02 ` Wolfgang Grandegger [this message]
2009-03-31 19:06 ` [PATCH v4 3/4] powerpc: NAND: FSL UPM: document new bindings Anton Vorontsov
2009-03-30 10:02 ` [PATCH v4 4/4] powerpc/85xx: TQM8548: Update DTS file for multi-chip support Wolfgang Grandegger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090330100555.282048633@denx.de \
--to=wg@grandegger$(echo .)com \
--cc=devicetree-discuss@ozlabs$(echo .)org \
--cc=linux-mtd@lists$(echo .)infradead.org \
--cc=linuxppc-dev@ozlabs$(echo .)org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox