From: Kishore Devireddy <kishorekrd@gmail•com>
To: linuxppc-embedded@ozlabs•org
Subject: MPC8245 custom board, Linux 2.4 kernel hangs after uncompressing
Date: Wed, 20 Apr 2005 18:00:46 -0700 [thread overview]
Message-ID: <2cf2641f0504201800556805d2@mail.gmail.com> (raw)
Hi
I am trying to run Embedded linux (ELDK) (2.4 kerenl) on a custom powerpc b=
oard,
which is similar to Artis A3000 board. This board has
mpc8245(XPC8245LZY266B), natsemi 83815 ethernet, 4MB intel e28f320
flash, 16MB winbond w986432DH-6 SDRAM. So I configured and compiled
U-boot for A3000 borad. U-boot worked on my board also. Next I
compiled ELDK 3.0 for Sandpoint 8245 board and copied to flash. But
linux hangs after uncompressing
U-Boot 1.1.2 (Apr 14 2005 - 00:02:29)
CPU: MPC8245 Revision 1.2 at 249.999 MHz: 16 kB I-Cache 16 kB D-Cache
Board: A3000 Local Bus at 99.999 MHz
I2C: ready
DRAM: 16 MB
FLASH: Get flash bank 0 @ 0xffc00000
Manuf. ID @ 0xff800000: 0x00000089
Device ID @ 0xff800001: 0x00000016
## Flash bank 0 at 0xffc00000 sizes: 0x00400000
protect monitor fff00000 @ 40000
protect environtment fffc0000 @ 20000
## Final Flash bank sizes: 00400000
4 MB
00 13 100b 0020 0200 ff
In: serial
Out: serial
Err: serial
Net: natsemi: EEPROM contents:
ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff ffff
dp83815#0
Warning: dp83815#0 MAC addresses don't match:
Address in SROM is FF:FF:FF:FF:FF:FF
Address in environment is 00:40:05:B0:F1:BA
A3000> tftpboot 400000 uImage.eldk
Using dp83815#0 device
TFTP from server 192.168.1.124; our IP address is 192.168.1.54
Filename 'uImage.eldk'.
Load address: 0x400000
Loading: #################################################################
#################################################################
###################
done
Bytes transferred =3D 757926 (b90a6 hex)
A3000> bootm
## Booting image at 00400000 ...
Image Name: Linux-2.4.25
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 757862 Bytes =3D 740.1 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
nothing happens after this until I reboot the board. I read u-boot FAQ
and configured bd_info structure same for both u-boot and Linux. I
found that CFG_IMMR is not applicable to MPC8245. I also used
clocks_in_mhz variable also before loading Linux. I am stuck here.
Could you please let me know what should I do next?
Thanks
Kishore
next reply other threads:[~2005-04-21 1:07 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-04-21 1:00 Kishore Devireddy [this message]
2005-04-22 14:03 ` MPC8245 custom board, Linux 2.4 kernel hangs after uncompressing Grant Likely
-- strict thread matches above, loose matches on Subject: below --
2005-04-21 5:52 Linuxppc-embedded Digest, Vol 8, Issue 56 Atit_Shah
2005-04-21 7:19 ` MPC8245 custom board, Linux 2.4 kernel hangs after uncompressing Sam Song
2005-04-21 7:46 ` Eugene Surovegin
2005-04-21 10:23 ` Wolfgang Denk
2005-04-21 22:53 ` Kishore Devireddy
2005-04-21 8:45 Atit_Shah
2005-04-21 9:58 Sam Song
2005-04-21 10:03 Sam Song
2005-04-22 2:30 Sam Song
2005-04-22 15:36 ` Mark A. Greer
2005-04-22 4:28 Atit_Shah
2005-04-22 5:35 ` Sam Song
2005-04-29 20:54 ` Kishore Devireddy
2005-04-22 6:20 Atit_Shah
2005-04-22 6:49 Sam Song
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2cf2641f0504201800556805d2@mail.gmail.com \
--to=kishorekrd@gmail$(echo .)com \
--cc=linuxppc-embedded@ozlabs$(echo .)org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox