Subject: Re: [RFC PATCH v7 6/8] ptp_ocp: implement DPLL ops

From: Vadim Fedorenko <[email-masked]>
Date: Fri, 5 May 2023 14:43:08 +0100

On 04/05/2023 10:27, Jiri Pirko wrote:
> Fri, Apr 28, 2023 at 02:20:07AM CEST, [email-masked] wrote:
>> From: Vadim Fedorenko <[email-masked]>
>>
>> Implement basic DPLL operations in ptp_ocp driver as the
>> simplest example of using new subsystem.
>>
>> Signed-off-by: Vadim Fedorenko <[email-masked]>
>> ---
>> drivers/ptp/Kconfig   |   1 +
>> drivers/ptp/ptp_ocp.c | 327 +++++++++++++++++++++++++++++++++++-------
>> 2 files changed, 276 insertions(+), 52 deletions(-)
>>
>> diff --git a/drivers/ptp/Kconfig b/drivers/ptp/Kconfig
>> index b00201d81313..e3575c2e34dc 100644
>> --- a/drivers/ptp/Kconfig
>> +++ b/drivers/ptp/Kconfig
>> @@ -177,6 +177,7 @@ config PTP_1588_CLOCK_OCP
>> 	depends on COMMON_CLK
>> 	select NET_DEVLINK
>> 	select CRC16
>> +	select DPLL
>> 	help
>> 	  This driver adds support for an OpenCompute time card.
>>
>> diff --git a/drivers/ptp/ptp_ocp.c b/drivers/ptp/ptp_ocp.c
>> index 2b63f3487645..100e5da0aeb3 100644
>> --- a/drivers/ptp/ptp_ocp.c
>> +++ b/drivers/ptp/ptp_ocp.c
>> @@ -23,6 +23,7 @@
>> #include <linux/mtd/mtd.h>
>> #include <linux/nvmem-consumer.h>
>> #include <linux/crc16.h>
>> +#include <linux/dpll.h>
>>
>> #define PCI_VENDOR_ID_FACEBOOK			0x1d9b
>> #define PCI_DEVICE_ID_FACEBOOK_TIMECARD		0x0400
>> @@ -261,12 +262,21 @@ enum ptp_ocp_sma_mode {
>> 	SMA_MODE_OUT,
>> };
>>
>> +static struct dpll_pin_frequency ptp_ocp_sma_freq[] = {
> 
> const

Forgot about this one, will change it.

> 
>> +	DPLL_PIN_FREQUENCY_1PPS,
>> +	DPLL_PIN_FREQUENCY_10MHZ,
>> +	DPLL_PIN_FREQUENCY_IRIG_B,
>> +	DPLL_PIN_FREQUENCY_DCF77,
>> +};
>> +
>> struct ptp_ocp_sma_connector {
>> 	enum	ptp_ocp_sma_mode mode;
>> 	bool	fixed_fcn;
>> 	bool	fixed_dir;
>> 	bool	disabled;
>> 	u8	default_fcn;
>> +	struct dpll_pin		   *dpll_pin;
>> +	struct dpll_pin_properties dpll_prop;
>> };
>>
>> struct ocp_attr_group {
>> @@ -295,6 +305,7 @@ struct ptp_ocp_serial_port {
>>
>> #define OCP_BOARD_ID_LEN		13
>> #define OCP_SERIAL_LEN			6
>> +#define OCP_SMA_NUM			4
>>
>> struct ptp_ocp {
>> 	struct pci_dev		*pdev;
>> @@ -351,8 +362,9 @@ struct ptp_ocp {
>> 	u32			ts_window_adjust;
>> 	u64			fw_cap;
>> 	struct ptp_ocp_signal	signal[4];
>> -	struct ptp_ocp_sma_connector sma[4];
>> +	struct ptp_ocp_sma_connector sma[OCP_SMA_NUM];
>> 	const struct ocp_sma_op *sma_op;
>> +	struct dpll_device *dpll;
>> };
>>
>> #define OCP_REQ_TIMESTAMP	BIT(0)
>> @@ -836,6 +848,7 @@ static DEFINE_IDR(ptp_ocp_idr);
>> struct ocp_selector {
>> 	const char *name;
>> 	int value;
>> +	u64 frequency;
>> };
>>
>> static const struct ocp_selector ptp_ocp_clock[] = {
>> @@ -856,31 +869,31 @@ static const struct ocp_selector ptp_ocp_clock[] = {
>> #define SMA_SELECT_MASK		GENMASK(14, 0)
>>
>> static const struct ocp_selector ptp_ocp_sma_in[] = {
>> -	{ .name = "10Mhz",	.value = 0x0000 },
>> -	{ .name = "PPS1",	.value = 0x0001 },
>> -	{ .name = "PPS2",	.value = 0x0002 },
>> -	{ .name = "TS1",	.value = 0x0004 },
>> -	{ .name = "TS2",	.value = 0x0008 },
>> -	{ .name = "IRIG",	.value = 0x0010 },
>> -	{ .name = "DCF",	.value = 0x0020 },
>> -	{ .name = "TS3",	.value = 0x0040 },
>> -	{ .name = "TS4",	.value = 0x0080 },
>> -	{ .name = "FREQ1",	.value = 0x0100 },
>> -	{ .name = "FREQ2",	.value = 0x0200 },
>> -	{ .name = "FREQ3",	.value = 0x0400 },
>> -	{ .name = "FREQ4",	.value = 0x0800 },
>> -	{ .name = "None",	.value = SMA_DISABLE },
>> +	{ .name = "10Mhz",  .value = 0x0000,      .frequency = 10000000 },
>> +	{ .name = "PPS1",   .value = 0x0001,      .frequency = 1 },
>> +	{ .name = "PPS2",   .value = 0x0002,      .frequency = 1 },
>> +	{ .name = "TS1",    .value = 0x0004,      .frequency = 0 },
>> +	{ .name = "TS2",    .value = 0x0008,      .frequency = 0 },
>> +	{ .name = "IRIG",   .value = 0x0010,      .frequency = 10000 },
>> +	{ .name = "DCF",    .value = 0x0020,      .frequency = 77500 },
>> +	{ .name = "TS3",    .value = 0x0040,      .frequency = 0 },
>> +	{ .name = "TS4",    .value = 0x0080,      .frequency = 0 },
>> +	{ .name = "FREQ1",  .value = 0x0100,      .frequency = 0 },
>> +	{ .name = "FREQ2",  .value = 0x0200,      .frequency = 0 },
>> +	{ .name = "FREQ3",  .value = 0x0400,      .frequency = 0 },
>> +	{ .name = "FREQ4",  .value = 0x0800,      .frequency = 0 },
>> +	{ .name = "None",   .value = SMA_DISABLE, .frequency = 0 },
>> 	{ }
>> };
>>
>> static const struct ocp_selector ptp_ocp_sma_out[] = {
>> -	{ .name = "10Mhz",	.value = 0x0000 },
>> -	{ .name = "PHC",	.value = 0x0001 },
>> -	{ .name = "MAC",	.value = 0x0002 },
>> -	{ .name = "GNSS1",	.value = 0x0004 },
>> -	{ .name = "GNSS2",	.value = 0x0008 },
>> -	{ .name = "IRIG",	.value = 0x0010 },
>> -	{ .name = "DCF",	.value = 0x0020 },
>> +	{ .name = "10Mhz",	.value = 0x0000,  .frequency = 10000000 },
>> +	{ .name = "PHC",	.value = 0x0001,  .frequency = 1 },
>> +	{ .name = "MAC",	.value = 0x0002,  .frequency = 1 },
>> +	{ .name = "GNSS1",	.value = 0x0004,  .frequency = 1 },
>> +	{ .name = "GNSS2",	.value = 0x0008,  .frequency = 1 },
>> +	{ .name = "IRIG",	.value = 0x0010,  .frequency = 10000 },
>> +	{ .name = "DCF",	.value = 0x0020,  .frequency = 77000 },
>> 	{ .name = "GEN1",	.value = 0x0040 },
>> 	{ .name = "GEN2",	.value = 0x0080 },
>> 	{ .name = "GEN3",	.value = 0x0100 },
>> @@ -891,15 +904,15 @@ static const struct ocp_selector ptp_ocp_sma_out[] = {
>> };
>>
>> static const struct ocp_selector ptp_ocp_art_sma_in[] = {
>> -	{ .name = "PPS1",	.value = 0x0001 },
>> -	{ .name = "10Mhz",	.value = 0x0008 },
>> +	{ .name = "PPS1",	.value = 0x0001,  .frequency = 1 },
>> +	{ .name = "10Mhz",	.value = 0x0008,  .frequency = 1000000 },
>> 	{ }
>> };
>>
>> static const struct ocp_selector ptp_ocp_art_sma_out[] = {
>> -	{ .name = "PHC",	.value = 0x0002 },
>> -	{ .name = "GNSS",	.value = 0x0004 },
>> -	{ .name = "10Mhz",	.value = 0x0010 },
>> +	{ .name = "PHC",	.value = 0x0002,  .frequency = 1 },
>> +	{ .name = "GNSS",	.value = 0x0004,  .frequency = 1 },
>> +	{ .name = "10Mhz",	.value = 0x0010,  .frequency = 10000000 },
>> 	{ }
>> };
>>
>> @@ -2283,22 +2296,34 @@ ptp_ocp_sma_fb_set_inputs(struct ptp_ocp *bp, int sma_nr, u32 val)
>> static void
>> ptp_ocp_sma_fb_init(struct ptp_ocp *bp)
>> {
>> +	struct dpll_pin_properties prop = {
> 
> Why don't you have this as static const outside the function?
> 

Because I'm changing label string for every pin. I cannot change it in
the const object.

>> +		.label = NULL,
> Pointless init.

Agree

>> +		.type = DPLL_PIN_TYPE_EXT,
>> +		.capabilities = DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE,
>> +		.freq_supported_num = ARRAY_SIZE(ptp_ocp_sma_freq),
>> +		.freq_supported = ptp_ocp_sma_freq,
>> +
>> +	};
>> 	u32 reg;
>> 	int i;
>>
>> 	/* defaults */
>> +	for (i = 0; i < OCP_SMA_NUM; i++) {
>> +		bp->sma[i].default_fcn = i & 1;
>> +		bp->sma[i].dpll_prop = prop;
>> +		bp->sma[i].dpll_prop.label = bp->ptp_info.pin_config[i].name;
>> +	}
>> 	bp->sma[0].mode = SMA_MODE_IN;
>> 	bp->sma[1].mode = SMA_MODE_IN;
>> 	bp->sma[2].mode = SMA_MODE_OUT;
>> 	bp->sma[3].mode = SMA_MODE_OUT;
>> -	for (i = 0; i < 4; i++)
>> -		bp->sma[i].default_fcn = i & 1;
>> -
>> 	/* If no SMA1 map, the pin functions and directions are fixed. */
>> 	if (!bp->sma_map1) {
>> -		for (i = 0; i < 4; i++) {
>> +		for (i = 0; i < OCP_SMA_NUM; i++) {
>> 			bp->sma[i].fixed_fcn = true;
>> 			bp->sma[i].fixed_dir = true;
>> +			bp->sma[1].dpll_prop.capabilities &=
>> +				~DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE;
>> 		}
>> 		return;
>> 	}
>> @@ -2308,7 +2333,7 @@ ptp_ocp_sma_fb_init(struct ptp_ocp *bp)
>> 	 */
>> 	reg = ioread32(&bp->sma_map2->gpio2);
>> 	if (reg == 0xffffffff) {
>> -		for (i = 0; i < 4; i++)
>> +		for (i = 0; i < OCP_SMA_NUM; i++)
>> 			bp->sma[i].fixed_dir = true;
>> 	} else {
>> 		reg = ioread32(&bp->sma_map1->gpio1);
>> @@ -2330,7 +2355,7 @@ static const struct ocp_sma_op ocp_fb_sma_op = {
>> };
>>
>> static int
>> -ptp_ocp_fb_set_pins(struct ptp_ocp *bp)
>> +ptp_ocp_set_pins(struct ptp_ocp *bp)
>> {
>> 	struct ptp_pin_desc *config;
>> 	int i;
>> @@ -2397,16 +2422,16 @@ ptp_ocp_fb_board_init(struct ptp_ocp *bp, struct ocp_resource *r)
>>
>> 	ptp_ocp_tod_init(bp);
>> 	ptp_ocp_nmea_out_init(bp);
>> -	ptp_ocp_sma_init(bp);
>> 	ptp_ocp_signal_init(bp);
>>
>> 	err = ptp_ocp_attr_group_add(bp, fb_timecard_groups);
>> 	if (err)
>> 		return err;
>>
>> -	err = ptp_ocp_fb_set_pins(bp);
>> +	err = ptp_ocp_set_pins(bp);
>> 	if (err)
>> 		return err;
>> +	ptp_ocp_sma_init(bp);
>>
>> 	return ptp_ocp_init_clock(bp);
>> }
>> @@ -2446,6 +2471,14 @@ ptp_ocp_register_resources(struct ptp_ocp *bp, kernel_ulong_t driver_data)
>> static void
>> ptp_ocp_art_sma_init(struct ptp_ocp *bp)
>> {
>> +	struct dpll_pin_properties prop = {
>> +		.label = NULL,
>> +		.type = DPLL_PIN_TYPE_EXT,
>> +		.capabilities = 0,
> 
> Same comment as to the similar prop struct above. Plus another pointless
> init here.
> 

Will remove pointless init.

> 
>> +		.freq_supported_num = ARRAY_SIZE(ptp_ocp_sma_freq),
>> +		.freq_supported = ptp_ocp_sma_freq,
>> +
>> +	};
>> 	u32 reg;
>> 	int i;
>>
>> @@ -2460,16 +2493,16 @@ ptp_ocp_art_sma_init(struct ptp_ocp *bp)
>> 	bp->sma[2].default_fcn = 0x10;	/* OUT: 10Mhz */
>> 	bp->sma[3].default_fcn = 0x02;	/* OUT: PHC */
>>
>> -	/* If no SMA map, the pin functions and directions are fixed. */
>> -	if (!bp->art_sma) {
>> -		for (i = 0; i < 4; i++) {
>> +
>> +	for (i = 0; i < OCP_SMA_NUM; i++) {
>> +		/* If no SMA map, the pin functions and directions are fixed. */
>> +		bp->sma[i].dpll_prop = prop;
>> +		bp->sma[i].dpll_prop.label = bp->ptp_info.pin_config[i].name;
>> +		if (!bp->art_sma) {
>> 			bp->sma[i].fixed_fcn = true;
>> 			bp->sma[i].fixed_dir = true;
>> +			continue;
>> 		}
>> -		return;
>> -	}
>> -
>> -	for (i = 0; i < 4; i++) {
>> 		reg = ioread32(&bp->art_sma->map[i].gpio);
>>
>> 		switch (reg & 0xff) {
>> @@ -2480,9 +2513,13 @@ ptp_ocp_art_sma_init(struct ptp_ocp *bp)
>> 		case 1:
>> 		case 8:
>> 			bp->sma[i].mode = SMA_MODE_IN;
>> +			bp->sma[i].dpll_prop.capabilities =
>> +				DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE;
>> 			break;
>> 		default:
>> 			bp->sma[i].mode = SMA_MODE_OUT;
>> +			bp->sma[i].dpll_prop.capabilities =
>> +				DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE;
>> 			break;
>> 		}
>> 	}
>> @@ -2549,6 +2586,9 @@ ptp_ocp_art_board_init(struct ptp_ocp *bp, struct ocp_resource *r)
>> 	/* Enable MAC serial port during initialisation */
>> 	iowrite32(1, &bp->board_config->mro50_serial_activate);
>>
>> +	err = ptp_ocp_set_pins(bp);
>> +	if (err)
>> +		return err;
>> 	ptp_ocp_sma_init(bp);
>>
>> 	err = ptp_ocp_attr_group_add(bp, art_timecard_groups);
>> @@ -2690,16 +2730,9 @@ sma4_show(struct device *dev, struct device_attribute *attr, char *buf)
>> }
>>
>> static int
>> -ptp_ocp_sma_store(struct ptp_ocp *bp, const char *buf, int sma_nr)
>> +ptp_ocp_sma_store_val(struct ptp_ocp *bp, int val, enum ptp_ocp_sma_mode mode, int sma_nr)
>> {
>> 	struct ptp_ocp_sma_connector *sma = &bp->sma[sma_nr - 1];
>> -	enum ptp_ocp_sma_mode mode;
>> -	int val;
>> -
>> -	mode = sma->mode;
>> -	val = sma_parse_inputs(bp->sma_op->tbl, buf, &mode);
>> -	if (val < 0)
>> -		return val;
>>
>> 	if (sma->fixed_dir && (mode != sma->mode || val & SMA_DISABLE))
>> 		return -EOPNOTSUPP;
>> @@ -2734,6 +2767,20 @@ ptp_ocp_sma_store(struct ptp_ocp *bp, const char *buf, int sma_nr)
>> 	return val;
>> }
>>
>> +static int
>> +ptp_ocp_sma_store(struct ptp_ocp *bp, const char *buf, int sma_nr)
>> +{
>> +	struct ptp_ocp_sma_connector *sma = &bp->sma[sma_nr - 1];
>> +	enum ptp_ocp_sma_mode mode;
>> +	int val;
>> +
>> +	mode = sma->mode;
>> +	val = sma_parse_inputs(bp->sma_op->tbl, buf, &mode);
>> +	if (val < 0)
>> +		return val;
>> +	return ptp_ocp_sma_store_val(bp, val, mode, sma_nr);
>> +}
>> +
>> static ssize_t
>> sma1_store(struct device *dev, struct device_attribute *attr,
>> 	   const char *buf, size_t count)
>> @@ -4172,12 +4219,148 @@ ptp_ocp_detach(struct ptp_ocp *bp)
>> 	device_unregister(&bp->dev);
>> }
>>
>> +static int ptp_ocp_dpll_lock_status_get(const struct dpll_device *dpll,
>> +					void *priv,
>> +					enum dpll_lock_status *status,
>> +					struct netlink_ext_ack *extack)
>> +{
>> +	struct ptp_ocp *bp = priv;
>> +	int sync;
>> +
>> +	sync = ioread32(&bp->reg->status) & OCP_STATUS_IN_SYNC;
>> +	*status = sync ? DPLL_LOCK_STATUS_LOCKED : DPLL_LOCK_STATUS_UNLOCKED;
> 
> Does your device support event delivery in case of the status change?
> ice and mlx5 drivers do poll for changes in this area anyway. It's a
> part of this patchset. You should do the same if your device does
> not support events.
> 
> Could you please implement notifications using
> dpll_device_notify() for status change and dpll_pin_notify() for pin
> state change?
> 

We are working on implementation of interrupt-based notifications, 
that's why I didn't implement polling code. Hopefully it will be ready 
before the non-RFC patchset submission.

> 
>> +
>> +	return 0;
>> +}
>> +
>> +static int ptp_ocp_dpll_source_idx_get(const struct dpll_device *dpll,
>> +				       void *priv, u32 *idx,
>> +				       struct netlink_ext_ack *extack)
>> +{
>> +	struct ptp_ocp *bp = priv;
>> +
>> +	if (bp->pps_select) {
>> +		*idx = ioread32(&bp->pps_select->gpio1);
>> +		return 0;
>> +	}
>> +	return -EINVAL;
>> +}
>> +
>> +static int ptp_ocp_dpll_mode_get(const struct dpll_device *dpll, void *priv,
>> +				 u32 *mode, struct netlink_ext_ack *extack)
>> +{
>> +	*mode = DPLL_MODE_AUTOMATIC;
>> +	return 0;
>> +}
>> +
>> +static bool ptp_ocp_dpll_mode_supported(const struct dpll_device *dpll,
>> +					void *priv, const enum dpll_mode mode,
>> +					struct netlink_ext_ack *extack)
>> +{
>> +	return mode == DPLL_MODE_AUTOMATIC;
>> +}
>> +
>> +static int ptp_ocp_dpll_direction_get(const struct dpll_pin *pin,
>> +				      void *pin_priv,
>> +				      const struct dpll_device *dpll,
>> +				      void *priv,
>> +				      enum dpll_pin_direction *direction,
>> +				      struct netlink_ext_ack *extack)
>> +{
>> +	struct ptp_ocp_sma_connector *sma = pin_priv;
>> +
>> +	*direction = sma->mode == SMA_MODE_IN ?
>> +				  DPLL_PIN_DIRECTION_SOURCE :
>> +				  DPLL_PIN_DIRECTION_OUTPUT;
>> +	return 0;
>> +}
>> +
>> +static int ptp_ocp_dpll_direction_set(const struct dpll_pin *pin,
>> +				      void *pin_priv,
>> +				      const struct dpll_device *dpll,
>> +				      void *dpll_priv,
>> +				      enum dpll_pin_direction direction,
>> +				      struct netlink_ext_ack *extack)
>> +{
>> +	struct ptp_ocp_sma_connector *sma = pin_priv;
>> +	struct ptp_ocp *bp = dpll_priv;
>> +	enum ptp_ocp_sma_mode mode;
>> +	int sma_nr = (sma - bp->sma);
>> +
>> +	if (sma->fixed_dir)
> 
> I believe that this is a pointless check as DPLL_PIN_CAPS_DIRECTION_CAN_CHANGE
> is not set and therefore the check in dpll_pin_direction_set() will be
> true and -EOPNOTSUPP will be returned from there.
> Remove this.

Yep, will do it.

> 
>> +		return -EOPNOTSUPP;
>> +	mode = direction == DPLL_PIN_DIRECTION_SOURCE ?
>> +			    SMA_MODE_IN : SMA_MODE_OUT;
>> +	return ptp_ocp_sma_store_val(bp, 0, mode, sma_nr);
> 
> You need sma_nr just here. Why can't you change ptp_ocp_sma_store_val()
> to accept struct ptp_ocp_sma_connector * instead avoiding the need for
> tne sma_nr completely?
>

I wanted to add minimal changes to the driver, I will consider changing 
this as a separate net-next patch.

> 
>> +}
>> +
>> +static int ptp_ocp_dpll_frequency_set(const struct dpll_pin *pin,
>> +				      void *pin_priv,
>> +				      const struct dpll_device *dpll,
>> +				      void *dpll_priv, u64 frequency,
>> +				      struct netlink_ext_ack *extack)
>> +{
>> +	struct ptp_ocp_sma_connector *sma = pin_priv;
>> +	struct ptp_ocp *bp = dpll_priv;
>> +	const struct ocp_selector *tbl;
>> +	int sma_nr = (sma - bp->sma);
>> +	int val, i;
>> +
>> +	if (sma->fixed_fcn)
> 
> In that case, just fill up a single frequency in the properties,
> avoid this check-fail and let the dpll core handle it.
> 

Makes sense.

> 
>> +		return -EOPNOTSUPP;
>> +
>> +	tbl = bp->sma_op->tbl[sma->mode];
>> +	for (i = 0; tbl[i].name; i++)
>> +		if (tbl[i].frequency == frequency)
>> +			return ptp_ocp_sma_store_val(bp, val, sma->mode, sma_nr);
>> +	return -EINVAL;
>> +}
>> +
>> +static int ptp_ocp_dpll_frequency_get(const struct dpll_pin *pin,
>> +				      void *pin_priv,
>> +				      const struct dpll_device *dpll,
>> +				      void *dpll_priv, u64 *frequency,
>> +				      struct netlink_ext_ack *extack)
>> +{
>> +	struct ptp_ocp_sma_connector *sma = pin_priv;
>> +	struct ptp_ocp *bp = dpll_priv;
>> +	const struct ocp_selector *tbl;
>> +	int sma_nr = (sma - bp->sma);
> 
> 1) void "()"s here.
> 2) why don't you fill the sma_nr in struct ptp_ocp_sma_connector to make
>     this easier to follow? IDK, just a suggestion, take or leave.
> 
> Same applies to the the rest of similar occurances above.
>

Will do it, yes.

> 
>> +	u32 val;
>> +	int i;
>> +
>> +	val = bp->sma_op->get(bp, sma_nr);
>> +	tbl = bp->sma_op->tbl[sma->mode];
>> +	for (i = 0; tbl[i].name; i++)
>> +		if (val == tbl[i].value) {
>> +			*frequency = tbl[i].frequency;
>> +			return 0;
>> +		}
>> +
>> +	return -EINVAL;
>> +}
>> +
>> +static const struct dpll_device_ops dpll_ops = {
>> +	.lock_status_get = ptp_ocp_dpll_lock_status_get,
>> +	.source_pin_idx_get = ptp_ocp_dpll_source_idx_get,
> 
> This op is a leftover, in dpll core it is not called. This was removed
> and agreed that drivers should implement state_on_dpll_get() op for pins
> to see which one is connected.
> 
> Please fix here and remove the leftover from DPLL patch #2 as well.
> 
> 
>> +	.mode_get = ptp_ocp_dpll_mode_get,
>> +	.mode_supported = ptp_ocp_dpll_mode_supported,
>> +};
>> +
>> +static const struct dpll_pin_ops dpll_pins_ops = {
>> +	.frequency_get = ptp_ocp_dpll_frequency_get,
>> +	.frequency_set = ptp_ocp_dpll_frequency_set,
>> +	.direction_get = ptp_ocp_dpll_direction_get,
>> +	.direction_set = ptp_ocp_dpll_direction_set,
>> +};
>> +
>> static int
>> ptp_ocp_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>> {
>> 	struct devlink *devlink;
>> 	struct ptp_ocp *bp;
>> -	int err;
>> +	int err, i;
>> +	u64 clkid;
>>
>> 	devlink = devlink_alloc(&ptp_ocp_devlink_ops, sizeof(*bp), &pdev->dev);
>> 	if (!devlink) {
>> @@ -4227,8 +4410,39 @@ ptp_ocp_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>>
>> 	ptp_ocp_info(bp);
>> 	devlink_register(devlink);
>> -	return 0;
>>
>> +	clkid = pci_get_dsn(pdev);
>> +	bp->dpll = dpll_device_get(clkid, 0, THIS_MODULE);
> 
> I suggested this the last time, but again: Could you please:
> 1) rename dpll_device_get to __dpll_device_get
> 2) introduce dpll_device_get as a macro filling up THIS_MODULE
> 
> Then drivers will just call always:
> bp->dpll = dpll_device_get(clkid, 0);
> and the macro will fillup the module automatically.
> 
> Please do the same for dpll_pin_get()
> 

Not sure why I have missed this part, but sure will do it.

> 
>> +	if (IS_ERR(bp->dpll)) {
>> +		dev_err(&pdev->dev, "dpll_device_alloc failed\n");
> 
> You need to fix your error path to call devlink_unregister() in this
> case.
> 
> 
>> +		goto out;
>> +	}
>> +
>> +	err = dpll_device_register(bp->dpll, DPLL_TYPE_PPS, &dpll_ops, bp, &pdev->dev);
>> +	if (err)
> 
> You need to fix your error path to call dpll_device_put() in this
> case.
> 

Ok, I'll re-check and update the error path for the next version.

> 
>> +		goto out;
>> +
>> +	for (i = 0; i < OCP_SMA_NUM; i++) {
>> +		bp->sma[i].dpll_pin = dpll_pin_get(clkid, i, THIS_MODULE, &bp->sma[i].dpll_prop);
>> +		if (IS_ERR(bp->sma[i].dpll_pin))
>> +			goto out_dpll;
>> +
>> +		err = dpll_pin_register(bp->dpll, bp->sma[i].dpll_pin, &dpll_pins_ops,
>> +					&bp->sma[i], NULL);
>> +		if (err) {
>> +			dpll_pin_put(bp->sma[i].dpll_pin);
>> +			goto out_dpll;
>> +		}
>> +	}
>> +
>> +	return 0;
>> +out_dpll:
>> +	while (i) {
>> +		--i;
> 
> 	while (i--) {
> 	?
> 
>> +		dpll_pin_unregister(bp->dpll, bp->sma[i].dpll_pin, &dpll_pins_ops, &bp->sma[i]);
>> +		dpll_pin_put(bp->sma[i].dpll_pin);
>> +	}
>> +	dpll_device_put(bp->dpll);
>> out:
>> 	ptp_ocp_detach(bp);
>> out_disable:
>> @@ -4243,7 +4457,16 @@ ptp_ocp_remove(struct pci_dev *pdev)
>> {
>> 	struct ptp_ocp *bp = pci_get_drvdata(pdev);
>> 	struct devlink *devlink = priv_to_devlink(bp);
>> +	int i;
>>
>> +	for (i = 0; i < OCP_SMA_NUM; i++) {
>> +		if (bp->sma[i].dpll_pin) {
> 
> Remove this pointless check. It is always true.

Agree.

> 
> 
>> +			dpll_pin_unregister(bp->dpll, bp->sma[i].dpll_pin, &dpll_pins_ops, bp);
>> +			dpll_pin_put(bp->sma[i].dpll_pin);
>> +		}
>> +	}
>> +	dpll_device_unregister(bp->dpll, &dpll_ops, bp);
>> +	dpll_device_put(bp->dpll);
>> 	devlink_unregister(devlink);
>> 	ptp_ocp_detach(bp);
>> 	pci_disable_device(pdev);
>> -- 
>> 2.34.1
>>