From: Stephen Hemminger <shemminger@linux-foundation•org>
To: Jeff Garzik <jgarzik@pobox•com>
Cc: netdev@vger•kernel.org
Cc: Greg KH <greg@kroah•com>
Subject: [PATCH 11/17] sky2: use MII defines
Date: Tue, 08 May 2007 20:50:00 -0700 [thread overview]
Message-ID: <20070509035030.079175041@linux-foundation.org> (raw)
In-Reply-To: 20070509034949.624934448@linux-foundation.org
[-- Attachment #1: use-mii-defines.patch --]
[-- Type: text/plain, Size: 14967 bytes --]
To make driver easier to understand, use the PHY register definitions
from standard mii.h include file rather than those inherited from sk98lin.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation•org>
---
drivers/net/sky2.c | 62 +++++++++----------
drivers/net/sky2.h | 166 ++++-------------------------------------------------
2 files changed, 43 insertions(+), 185 deletions(-)
--- sky2-2.6.21.orig/drivers/net/sky2.c 2007-05-08 10:29:17.000000000 -0700
+++ sky2-2.6.21/drivers/net/sky2.c 2007-05-08 10:29:21.000000000 -0700
@@ -268,17 +268,17 @@ static void sky2_gmac_reset(struct sky2_
/* flow control to advertise bits */
static const u16 copper_fc_adv[] = {
[FC_NONE] = 0,
- [FC_TX] = PHY_M_AN_ASP,
- [FC_RX] = PHY_M_AN_PC,
- [FC_BOTH] = PHY_M_AN_PC | PHY_M_AN_ASP,
+ [FC_TX] = ADVERTISE_PAUSE_ASYM,
+ [FC_RX] = ADVERTISE_PAUSE_CAP,
+ [FC_BOTH] = ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM,
};
/* flow control to advertise bits when using 1000BaseX */
static const u16 fiber_fc_adv[] = {
- [FC_BOTH] = PHY_M_P_BOTH_MD_X,
- [FC_TX] = PHY_M_P_ASYM_MD_X,
- [FC_RX] = PHY_M_P_SYM_MD_X,
- [FC_NONE] = PHY_M_P_NO_PAUSE_X,
+ [FC_NONE] = 0,
+ [FC_TX] = ADVERTISE_1000XPAUSE,
+ [FC_RX] = ADVERTISE_1000XPSE_ASYM,
+ [FC_BOTH] = ADVERTISE_1000XPAUSE | ADVERTISE_1000XPSE_ASYM,
};
/* flow control to GMA disable bits */
@@ -360,69 +360,67 @@ static void sky2_phy_init(struct sky2_hw
/* for SFP-module set SIGDET polarity to low */
ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
ctrl |= PHY_M_FIB_SIGD_POL;
- gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+ gm_phy_write(hw, port, MII_BMCR, ctrl);
}
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
- ctrl = PHY_CT_RESET;
+ ctrl = BMCR_RESET;
ct1000 = 0;
- adv = PHY_AN_CSMA;
+ adv = ADVERTISE_CSMA;
reg = 0;
if (sky2->autoneg == AUTONEG_ENABLE) {
if (sky2_is_copper(hw)) {
if (sky2->advertising & ADVERTISED_1000baseT_Full)
- ct1000 |= PHY_M_1000C_AFD;
+ ct1000 |= ADVERTISE_1000FULL;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
- ct1000 |= PHY_M_1000C_AHD;
+ ct1000 |= ADVERTISE_1000HALF;
if (sky2->advertising & ADVERTISED_100baseT_Full)
- adv |= PHY_M_AN_100_FD;
+ adv |= ADVERTISE_100FULL;
if (sky2->advertising & ADVERTISED_100baseT_Half)
- adv |= PHY_M_AN_100_HD;
+ adv |= ADVERTISE_100HALF;
if (sky2->advertising & ADVERTISED_10baseT_Full)
- adv |= PHY_M_AN_10_FD;
+ adv |= ADVERTISE_10FULL;
if (sky2->advertising & ADVERTISED_10baseT_Half)
- adv |= PHY_M_AN_10_HD;
+ adv |= ADVERTISE_10HALF;
adv |= copper_fc_adv[sky2->flow_mode];
} else { /* special defines for FIBER (88E1040S only) */
if (sky2->advertising & ADVERTISED_1000baseT_Full)
- adv |= PHY_M_AN_1000X_AFD;
+ adv |= ADVERTISE_1000XFULL;
if (sky2->advertising & ADVERTISED_1000baseT_Half)
- adv |= PHY_M_AN_1000X_AHD;
+ adv |= ADVERTISE_1000XHALF;
adv |= fiber_fc_adv[sky2->flow_mode];
}
/* Restart Auto-negotiation */
- ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;
+ ctrl |= BMCR_ANRESTART | BMCR_ANENABLE;
} else {
/* forced speed/duplex settings */
- ct1000 = PHY_M_1000C_MSE;
/* Disable auto update for duplex flow control and speed */
reg |= GM_GPCR_AU_ALL_DIS;
switch (sky2->speed) {
case SPEED_1000:
- ctrl |= PHY_CT_SP1000;
+ ctrl |= BMCR_SPEED1000;
reg |= GM_GPCR_SPEED_1000;
break;
case SPEED_100:
- ctrl |= PHY_CT_SP100;
+ ctrl |= BMCR_SPEED100;
reg |= GM_GPCR_SPEED_100;
break;
}
if (sky2->duplex == DUPLEX_FULL) {
reg |= GM_GPCR_DUP_FULL;
- ctrl |= PHY_CT_DUP_MD;
+ ctrl |= BMCR_FULLDPLX;
} else if (sky2->speed < SPEED_1000)
sky2->flow_mode = FC_NONE;
-
reg |= gm_fc_disable[sky2->flow_mode];
/* Forward pause packets to GMAC? */
@@ -435,10 +433,10 @@ static void sky2_phy_init(struct sky2_hw
gma_write16(hw, port, GM_GP_CTRL, reg);
if (hw->chip_id != CHIP_ID_YUKON_FE)
- gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000);
+ gm_phy_write(hw, port, MII_CTRL1000, ct1000);
- gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv);
- gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
+ gm_phy_write(hw, port, MII_ADVERTISE, adv);
+ gm_phy_write(hw, port, MII_BMCR, ctrl);
/* Setup Phy LED's */
ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS);
@@ -661,8 +659,8 @@ static void sky2_mac_init(struct sky2_hw
do {
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR);
- } while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL ||
- gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 ||
+ } while (gm_phy_read(hw, 1, MII_PHYSID1) != ID1_MARVELL ||
+ gm_phy_read(hw, 1, MII_PHYSID2) != ID2_Y2 ||
gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0);
}
@@ -1762,9 +1760,9 @@ static int sky2_autoneg_done(struct sky2
unsigned port = sky2->port;
u16 advert, lpa;
- advert = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
- lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP);
- if (lpa & PHY_M_AN_RF) {
+ advert = gm_phy_read(hw, port, MII_ADVERTISE);
+ lpa = gm_phy_read(hw, port, MII_LPA);
+ if (lpa & LPA_RFAULT) {
printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name);
return -1;
}
--- sky2-2.6.21.orig/drivers/net/sky2.h 2007-05-08 10:29:05.000000000 -0700
+++ sky2-2.6.21/drivers/net/sky2.h 2007-05-08 10:29:21.000000000 -0700
@@ -851,32 +851,18 @@ enum {
* Marvel-PHY Registers, indirect addressed over GMAC
*/
enum {
- PHY_MARV_CTRL = 0x00,/* 16 bit r/w PHY Control Register */
- PHY_MARV_STAT = 0x01,/* 16 bit r/o PHY Status Register */
- PHY_MARV_ID0 = 0x02,/* 16 bit r/o PHY ID0 Register */
- PHY_MARV_ID1 = 0x03,/* 16 bit r/o PHY ID1 Register */
- PHY_MARV_AUNE_ADV = 0x04,/* 16 bit r/w Auto-Neg. Advertisement */
- PHY_MARV_AUNE_LP = 0x05,/* 16 bit r/o Link Part Ability Reg */
- PHY_MARV_AUNE_EXP = 0x06,/* 16 bit r/o Auto-Neg. Expansion Reg */
- PHY_MARV_NEPG = 0x07,/* 16 bit r/w Next Page Register */
- PHY_MARV_NEPG_LP = 0x08,/* 16 bit r/o Next Page Link Partner */
/* Marvel-specific registers */
- PHY_MARV_1000T_CTRL = 0x09,/* 16 bit r/w 1000Base-T Control Reg */
- PHY_MARV_1000T_STAT = 0x0a,/* 16 bit r/o 1000Base-T Status Reg */
- PHY_MARV_EXT_STAT = 0x0f,/* 16 bit r/o Extended Status Reg */
PHY_MARV_PHY_CTRL = 0x10,/* 16 bit r/w PHY Specific Ctrl Reg */
PHY_MARV_PHY_STAT = 0x11,/* 16 bit r/o PHY Specific Stat Reg */
PHY_MARV_INT_MASK = 0x12,/* 16 bit r/w Interrupt Mask Reg */
PHY_MARV_INT_STAT = 0x13,/* 16 bit r/o Interrupt Status Reg */
PHY_MARV_EXT_CTRL = 0x14,/* 16 bit r/w Ext. PHY Specific Ctrl */
- PHY_MARV_RXE_CNT = 0x15,/* 16 bit r/w Receive Error Counter */
+
PHY_MARV_EXT_ADR = 0x16,/* 16 bit r/w Ext. Ad. for Cable Diag. */
- PHY_MARV_PORT_IRQ = 0x17,/* 16 bit r/o Port 0 IRQ (88E1111 only) */
+
PHY_MARV_LED_CTRL = 0x18,/* 16 bit r/w LED Control Reg */
PHY_MARV_LED_OVER = 0x19,/* 16 bit r/w Manual LED Override Reg */
- PHY_MARV_EXT_CTRL_2 = 0x1a,/* 16 bit r/w Ext. PHY Specific Ctrl 2 */
- PHY_MARV_EXT_P_STAT = 0x1b,/* 16 bit r/w Ext. PHY Spec. Stat Reg */
- PHY_MARV_CABLE_DIAG = 0x1c,/* 16 bit r/o Cable Diagnostic Reg */
+
PHY_MARV_PAGE_ADDR = 0x1d,/* 16 bit r/w Extended Page Address Reg */
PHY_MARV_PAGE_DATA = 0x1e,/* 16 bit r/w Extended Page Data Reg */
@@ -888,133 +874,16 @@ enum {
PHY_MARV_FE_SPEC_2 = 0x1c,/* 16 bit r/w Specific Control Reg. 2 */
};
-enum {
- PHY_CT_RESET = 1<<15, /* Bit 15: (sc) clear all PHY related regs */
- PHY_CT_LOOP = 1<<14, /* Bit 14: enable Loopback over PHY */
- PHY_CT_SPS_LSB = 1<<13, /* Bit 13: Speed select, lower bit */
- PHY_CT_ANE = 1<<12, /* Bit 12: Auto-Negotiation Enabled */
- PHY_CT_PDOWN = 1<<11, /* Bit 11: Power Down Mode */
- PHY_CT_ISOL = 1<<10, /* Bit 10: Isolate Mode */
- PHY_CT_RE_CFG = 1<<9, /* Bit 9: (sc) Restart Auto-Negotiation */
- PHY_CT_DUP_MD = 1<<8, /* Bit 8: Duplex Mode */
- PHY_CT_COL_TST = 1<<7, /* Bit 7: Collision Test enabled */
- PHY_CT_SPS_MSB = 1<<6, /* Bit 6: Speed select, upper bit */
-};
-
-enum {
- PHY_CT_SP1000 = PHY_CT_SPS_MSB, /* enable speed of 1000 Mbps */
- PHY_CT_SP100 = PHY_CT_SPS_LSB, /* enable speed of 100 Mbps */
- PHY_CT_SP10 = 0, /* enable speed of 10 Mbps */
-};
-
-enum {
- PHY_ST_EXT_ST = 1<<8, /* Bit 8: Extended Status Present */
-
- PHY_ST_PRE_SUP = 1<<6, /* Bit 6: Preamble Suppression */
- PHY_ST_AN_OVER = 1<<5, /* Bit 5: Auto-Negotiation Over */
- PHY_ST_REM_FLT = 1<<4, /* Bit 4: Remote Fault Condition Occured */
- PHY_ST_AN_CAP = 1<<3, /* Bit 3: Auto-Negotiation Capability */
- PHY_ST_LSYNC = 1<<2, /* Bit 2: Link Synchronized */
- PHY_ST_JAB_DET = 1<<1, /* Bit 1: Jabber Detected */
- PHY_ST_EXT_REG = 1<<0, /* Bit 0: Extended Register available */
-};
-
-enum {
- PHY_I1_OUI_MSK = 0x3f<<10, /* Bit 15..10: Organization Unique ID */
- PHY_I1_MOD_NUM = 0x3f<<4, /* Bit 9.. 4: Model Number */
- PHY_I1_REV_MSK = 0xf, /* Bit 3.. 0: Revision Number */
-};
-
/* different Marvell PHY Ids */
enum {
- PHY_MARV_ID0_VAL= 0x0141, /* Marvell Unique Identifier */
+ ID1_MARVELL= 0x0141, /* Marvell Unique Identifier */
- PHY_BCOM_ID1_A1 = 0x6041,
- PHY_BCOM_ID1_B2 = 0x6043,
- PHY_BCOM_ID1_C0 = 0x6044,
- PHY_BCOM_ID1_C5 = 0x6047,
-
- PHY_MARV_ID1_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
- PHY_MARV_ID1_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
- PHY_MARV_ID1_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
- PHY_MARV_ID1_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
- PHY_MARV_ID1_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */
- PHY_MARV_ID1_ECU= 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */
-};
-
-/* Advertisement register bits */
-enum {
- PHY_AN_NXT_PG = 1<<15, /* Bit 15: Request Next Page */
- PHY_AN_ACK = 1<<14, /* Bit 14: (ro) Acknowledge Received */
- PHY_AN_RF = 1<<13, /* Bit 13: Remote Fault Bits */
-
- PHY_AN_PAUSE_ASYM = 1<<11,/* Bit 11: Try for asymmetric */
- PHY_AN_PAUSE_CAP = 1<<10, /* Bit 10: Try for pause */
- PHY_AN_100BASE4 = 1<<9, /* Bit 9: Try for 100mbps 4k packets */
- PHY_AN_100FULL = 1<<8, /* Bit 8: Try for 100mbps full-duplex */
- PHY_AN_100HALF = 1<<7, /* Bit 7: Try for 100mbps half-duplex */
- PHY_AN_10FULL = 1<<6, /* Bit 6: Try for 10mbps full-duplex */
- PHY_AN_10HALF = 1<<5, /* Bit 5: Try for 10mbps half-duplex */
- PHY_AN_CSMA = 1<<0, /* Bit 0: Only selector supported */
- PHY_AN_SEL = 0x1f, /* Bit 4..0: Selector Field, 00001=Ethernet*/
- PHY_AN_FULL = PHY_AN_100FULL | PHY_AN_10FULL | PHY_AN_CSMA,
- PHY_AN_ALL = PHY_AN_10HALF | PHY_AN_10FULL |
- PHY_AN_100HALF | PHY_AN_100FULL,
-};
-
-/***** PHY_BCOM_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
-/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
-enum {
- PHY_B_1000S_MSF = 1<<15, /* Bit 15: Master/Slave Fault */
- PHY_B_1000S_MSR = 1<<14, /* Bit 14: Master/Slave Result */
- PHY_B_1000S_LRS = 1<<13, /* Bit 13: Local Receiver Status */
- PHY_B_1000S_RRS = 1<<12, /* Bit 12: Remote Receiver Status */
- PHY_B_1000S_LP_FD = 1<<11, /* Bit 11: Link Partner can FD */
- PHY_B_1000S_LP_HD = 1<<10, /* Bit 10: Link Partner can HD */
- /* Bit 9..8: reserved */
- PHY_B_1000S_IEC = 0xff, /* Bit 7..0: Idle Error Count */
-};
-
-/** Marvell-Specific */
-enum {
- PHY_M_AN_NXT_PG = 1<<15, /* Request Next Page */
- PHY_M_AN_ACK = 1<<14, /* (ro) Acknowledge Received */
- PHY_M_AN_RF = 1<<13, /* Remote Fault */
-
- PHY_M_AN_ASP = 1<<11, /* Asymmetric Pause */
- PHY_M_AN_PC = 1<<10, /* MAC Pause implemented */
- PHY_M_AN_100_T4 = 1<<9, /* Not cap. 100Base-T4 (always 0) */
- PHY_M_AN_100_FD = 1<<8, /* Advertise 100Base-TX Full Duplex */
- PHY_M_AN_100_HD = 1<<7, /* Advertise 100Base-TX Half Duplex */
- PHY_M_AN_10_FD = 1<<6, /* Advertise 10Base-TX Full Duplex */
- PHY_M_AN_10_HD = 1<<5, /* Advertise 10Base-TX Half Duplex */
- PHY_M_AN_SEL_MSK =0x1f<<4, /* Bit 4.. 0: Selector Field Mask */
-};
-
-/* special defines for FIBER (88E1011S only) */
-enum {
- PHY_M_AN_ASP_X = 1<<8, /* Asymmetric Pause */
- PHY_M_AN_PC_X = 1<<7, /* MAC Pause implemented */
- PHY_M_AN_1000X_AHD = 1<<6, /* Advertise 10000Base-X Half Duplex */
- PHY_M_AN_1000X_AFD = 1<<5, /* Advertise 10000Base-X Full Duplex */
-};
-
-/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
-enum {
- PHY_M_P_NO_PAUSE_X = 0<<7,/* Bit 8.. 7: no Pause Mode */
- PHY_M_P_SYM_MD_X = 1<<7, /* Bit 8.. 7: symmetric Pause Mode */
- PHY_M_P_ASYM_MD_X = 2<<7,/* Bit 8.. 7: asymmetric Pause Mode */
- PHY_M_P_BOTH_MD_X = 3<<7,/* Bit 8.. 7: both Pause Mode */
-};
-
-/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
-enum {
- PHY_M_1000C_TEST = 7<<13,/* Bit 15..13: Test Modes */
- PHY_M_1000C_MSE = 1<<12, /* Manual Master/Slave Enable */
- PHY_M_1000C_MSC = 1<<11, /* M/S Configuration (1=Master) */
- PHY_M_1000C_MPD = 1<<10, /* Multi-Port Device */
- PHY_M_1000C_AFD = 1<<9, /* Advertise Full Duplex */
- PHY_M_1000C_AHD = 1<<8, /* Advertise Half Duplex */
+ ID2_B0 = 0x0C23, /* Yukon (PHY 88E1011) */
+ ID2_B2 = 0x0C25, /* Yukon-Plus (PHY 88E1011) */
+ ID2_C2 = 0x0CC2, /* Yukon-EC (PHY 88E1111) */
+ ID2_Y2 = 0x0C91, /* Yukon-2 (PHY 88E1112) */
+ ID2_FE = 0x0C83, /* Yukon-FE (PHY 88E3082 Rev.A1) */
+ ID2_ECU = 0x0CB0, /* Yukon-ECU (PHY 88E1149 Rev.B2?) */
};
/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
@@ -1031,9 +900,7 @@ enum {
PHY_M_PC_SQE_T_ENA = 1<<2, /* SQE Test Enabled */
PHY_M_PC_POL_R_DIS = 1<<1, /* Polarity Reversal Disabled */
PHY_M_PC_DIS_JABBER = 1<<0, /* Disable Jabber */
-};
-enum {
PHY_M_PC_EN_DET = 2<<8, /* Energy Detect (Mode 1) */
PHY_M_PC_EN_DET_PLUS = 3<<8, /* Energy Detect Plus (Mode 2) */
};
@@ -1292,15 +1159,8 @@ enum {
LED_PAR_CTRL_INACT = 0x0f
};
-/*****,PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
-enum {
- PHY_M_FESC_DIS_WAIT = 1<<2, /* Disable TDR Waiting Period */
- PHY_M_FESC_ENA_MCLK = 1<<1, /* Enable MAC Rx Clock in sleep mode */
- PHY_M_FESC_SEL_CL_A = 1<<0, /* Select Class A driver (100B-TX) */
-};
-
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
-/***** PHY_MARV_PHY_CTRL (page 1) 16 bit r/w Fiber Specific Ctrl *****/
+/* PHY_MARV_PHY_CTRL (page 1) 16 bit r/w Fiber Specific Ctrl */
enum {
PHY_M_FIB_FORCE_LNK = 1<<10,/* Force Link Good */
PHY_M_FIB_SIGD_POL = 1<<9, /* SIGDET Polarity */
@@ -1308,7 +1168,7 @@ enum {
};
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
-/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
+/* PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl */
enum {
PHY_M_MAC_MD_MSK = 7<<7, /* Bit 9.. 7: Mode Select Mask */
PHY_M_MAC_MD_AUTO = 3,/* Auto Copper/1000Base-X */
@@ -1317,7 +1177,7 @@ enum {
};
#define PHY_M_MAC_MODE_SEL(x) (((x)<<7) & PHY_M_MAC_MD_MSK)
-/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
+/* PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. */
enum {
PHY_M_LEDC_LOS_MSK = 0xf<<12,/* Bit 15..12: LOS LED Ctrl. Mask */
PHY_M_LEDC_INIT_MSK = 0xf<<8, /* Bit 11.. 8: INIT LED Ctrl. Mask */
--
next prev parent reply other threads:[~2007-05-09 4:04 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-05-09 3:49 [PATCH 00/17] sky2 update for 2.6.22 Stephen Hemminger
2007-05-09 3:49 ` [PATCH 01/17] sky2: fix oops on shutdown Stephen Hemminger
2007-05-09 3:49 ` [PATCH 02/17] sky2: dont restrict config space access Stephen Hemminger
2007-05-09 3:49 ` [PATCH 03/17] sky2: keep track of receive alloc failures Stephen Hemminger
2007-05-09 3:49 ` [PATCH 04/17] sky2: remove dual port workaround Stephen Hemminger
2007-05-09 3:49 ` [PATCH 05/17] pci: advanced error reporting stub return values Stephen Hemminger
2007-05-10 15:48 ` Stephen Hemminger
2007-05-09 3:49 ` [PATCH 06/17] sky2: advanced error reporting Stephen Hemminger
2007-05-09 17:05 ` Linas Vepstas
2007-05-09 22:35 ` Stephen Hemminger
2007-05-09 3:49 ` [PATCH 07/17] sky2: use pci_config access functions Stephen Hemminger
2007-05-09 3:49 ` [PATCH 08/17] sky2: MIB counter overflow handling Stephen Hemminger
2007-05-09 3:49 ` [PATCH 09/17] sky2: memory barriers change Stephen Hemminger
2007-05-09 3:49 ` [PATCH 10/17] sky2: add prefetch for next skb on receive Stephen Hemminger
2007-05-09 3:50 ` Stephen Hemminger [this message]
2007-05-09 3:50 ` [PATCH 12/17] sky2: chip id enum Stephen Hemminger
2007-05-09 3:50 ` [PATCH 13/17] sky2: whitespace cleanups Stephen Hemminger
2007-05-09 3:50 ` [PATCH 14/17] pci_wake_enabled function Stephen Hemminger
2007-05-09 3:50 ` [PATCH 15/17] sky2: only disable 88e8056 on some boards Stephen Hemminger
2007-05-09 3:50 ` [PATCH 16/17] sky2: make sure high DMA bits set Stephen Hemminger
2007-05-09 3:50 ` [PATCH 17/17] sky2: version 1.15 Stephen Hemminger
2007-05-09 4:16 ` [PATCH 00/17] sky2 update for 2.6.22 Jeff Garzik
2007-05-09 14:48 ` Stephen Hemminger
2007-05-09 23:27 ` Jeff Garzik
2007-05-10 5:08 ` Stephen Hemminger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070509035030.079175041@linux-foundation.org \
--to=shemminger@linux-foundation$(echo .)org \
--cc=jgarzik@pobox$(echo .)com \
--cc=netdev@vger$(echo .)kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox