Subject: [PATCH] smsc911x: add fifo byteswap support V2

From: Magnus Damm <[email-masked]>
Date: Tue, 28 Apr 2009 16:32:16 +0900

From: Magnus Damm <[email-masked]>

This is V2 of the smsc911x fifo byteswap patch.

The smsc911x hardware supports both big and little and endian
hardware configurations, and the linux smsc911x driver currently
detects word order.

For correct operation on big endian platforms lacking swapped
byte lanes the following patch is needed. Only fifo data is
swapped, register data does not require any swapping. 

Signed-off-by: Magnus Damm <[email-masked]>
---

 Changes since V1:
 - Added SMSC911X_SWAP_FIFO comment to header file, thanks Steve!

 Platform data for the rsk7203 board will be posted separately
 to the linux-sh list in the near future.

 drivers/net/smsc911x.c   |   13 +++++++++++++
 include/linux/smsc911x.h |   10 ++++++++++
 2 files changed, 23 insertions(+)

--- 0001/drivers/net/smsc911x.c
+++ work/drivers/net/smsc911x.c	2009-04-28 15:34:56.000000000 +0900
@@ -47,6 +47,7 @@
 #include <linux/bitops.h>
 #include <linux/irq.h>
 #include <linux/io.h>
+#include <linux/swab.h>
 #include <linux/phy.h>
 #include <linux/smsc911x.h>
 #include "smsc911x.h"
@@ -175,6 +176,12 @@ static inline void
 smsc911x_tx_writefifo(struct smsc911x_data *pdata, unsigned int *buf,
 		      unsigned int wordcount)
 {
+	if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
+		while (wordcount--)
+			smsc911x_reg_write(pdata, TX_DATA_FIFO, swab32(*buf++));
+		return;
+	}
+
 	if (pdata->config.flags & SMSC911X_USE_32BIT) {
 		writesl(pdata->ioaddr + TX_DATA_FIFO, buf, wordcount);
 		return;
@@ -194,6 +201,12 @@ static inline void
 smsc911x_rx_readfifo(struct smsc911x_data *pdata, unsigned int *buf,
 		     unsigned int wordcount)
 {
+	if (pdata->config.flags & SMSC911X_SWAP_FIFO) {
+		while (wordcount--)
+			*buf++ = swab32(smsc911x_reg_read(pdata, RX_DATA_FIFO));
+		return;
+	}
+
 	if (pdata->config.flags & SMSC911X_USE_32BIT) {
 		readsl(pdata->ioaddr + RX_DATA_FIFO, buf, wordcount);
 		return;
--- 0001/include/linux/smsc911x.h
+++ work/include/linux/smsc911x.h	2009-04-28 15:31:07.000000000 +0900
@@ -47,4 +47,14 @@ struct smsc911x_platform_config {
 #define SMSC911X_FORCE_EXTERNAL_PHY 		(BIT(3))
 #define SMSC911X_SAVE_MAC_ADDRESS		(BIT(4))
 
+/*
+ * SMSC911X_SWAP_FIFO:
+ * Enables software byte swap for fifo data. Should only be used as a
+ * "last resort" in the case of big endian mode on boards with incorrectly
+ * routed data bus to older devices such as LAN9118. Newer devices such as
+ * LAN9221 can handle this in hardware, there are registers to control
+ * this swapping but the driver doesn't currently use them.
+ */
+#define SMSC911X_SWAP_FIFO			(BIT(5))
+
 #endif /* __LINUX_SMSC911X_H__ */