Subject: Re: [PATCH v4 03/10] ARM: sun8i: dt: Add DT bindings documentation for Allwinner sun8i-emac

From: Rob Herring <[email-masked]>
Date: Mon, 10 Oct 2016 10:13:35 -0500

On Fri, Oct 07, 2016 at 10:25:50AM +0200, Corentin Labbe wrote:
> This patch adds documentation for Device-Tree bindings for the
> Allwinner sun8i-emac driver.
> 
> Signed-off-by: Corentin Labbe <[email-masked]>
> ---
>  .../bindings/net/allwinner,sun8i-emac.txt          | 70 ++++++++++++++++++++++
>  1 file changed, 70 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> new file mode 100644
> index 0000000..92e4ef3b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-emac.txt
> @@ -0,0 +1,70 @@
> +* Allwinner sun8i EMAC ethernet controller
> +
> +Required properties:
> +- compatible: should be one of the following string:
> +		"allwinner,sun8i-a83t-emac"
> +		"allwinner,sun8i-h3-emac"
> +		"allwinner,sun50i-a64-emac"
> +- reg: address and length of the register for the device.
> +- syscon: A phandle to the syscon of the SoC
> +- interrupts: interrupt for the device
> +- clocks: A phandle to the reference clock for this device
> +- clock-names: should be "ahb"
> +- resets: A phandle to the reset control for this device
> +- reset-names: should be "ahb"
> +- phy-mode: See ethernet.txt
> +- phy-handle: See ethernet.txt
> +- #address-cells: shall be 1
> +- #size-cells: shall be 0
> +
> +Optional properties:
> +- allwinner,tx-delay: TX clock delay chain value. Range value is 0-0x07. Default is 0)
> +- allwinner,rx-delay: RX clock delay chain value. Range value is 0-0x1F. Default is 0)
> +Both delay properties does not have units, there are arbitrary value.

They have to have some sort of units. Some number of clocks perhaps. Or 
just say what register field they correspond to.

> +The TX/RX clock delay chain settings are board specific and could be found
> +in vendor FEX files.
> +
> +Optional properties for "allwinner,sun8i-h3-emac":
> +- allwinner,leds-active-low: EPHY LEDs are active low
> +
> +Required child node of emac:
> +- mdio bus node: should be named mdio
> +
> +Required properties of the mdio node:
> +- #address-cells: shall be 1
> +- #size-cells: shall be 0
> +
> +The device node referenced by "phy" or "phy-handle" should be a child node
> +of the mdio node. See phy.txt for the generic PHY bindings.
> +
> +Required properties of the phy node with "allwinner,sun8i-h3-emac":
> +- clocks: an extra phandle to the reference clock for the EPHY
> +- resets: an extra phandle to the reset control for the EPHY
> +
> +Example:
> +
> +emac: ethernet@01c0b000 {

Drop leading 0.

> +	compatible = "allwinner,sun8i-h3-emac";
> +	syscon = <&syscon>;
> +	reg = <0x01c0b000 0x104>;
> +	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> +	resets = <&ccu RST_BUS_EMAC>;
> +	reset-names = "ahb";
> +	clocks = <&ccu CLK_BUS_EMAC>;
> +	clock-names = "ahb";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	phy = <&int_mii_phy>;
> +	phy-mode = "mii";
> +	allwinner,leds-active-low;
> +	mdio: mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		int_mii_phy: ethernet-phy@1 {
> +			reg = <1>;
> +			clocks = <&ccu CLK_BUS_EPHY>;
> +			resets = <&ccu RST_BUS_EPHY>;
> +		};
> +	};
> +};
> -- 
> 2.7.3
>