Subject: Re: [RFC 1/4] Documentation: devicetree: add multiple cpu port DSA binding

From: Andrew Lunn <[email-masked]>
Date: Wed, 4 Jan 2017 13:58:37 +0100

On Wed, Jan 04, 2017 at 08:38:01AM +0100, John Crispin wrote:
> From: Andrew Lunn <[email-masked]>
> 
> Extend the DSA binding documentation, adding the new properties required
> when there is more than one CPU port attached to the switch.

Hi John

Thanks for picking up my old patches.

> Cc: Rob Herring <[email-masked]>
> Cc: [email-masked]
> Signed-off-by: Andrew Lunn <[email-masked]>
> ---
>  Documentation/devicetree/bindings/net/dsa/dsa.txt |   67 ++++++++++++++++++++-
>  1 file changed, 66 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
> index a4a570f..fc901cf 100644
> --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt
> +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
> @@ -337,13 +337,25 @@ Optional property:
>  			  This mii-bus will be used in preference to the
>  			  global dsa,mii-bus defined above, for this switch.
>  
> +- ethernet		: Optional for "cpu" ports. A phandle to an ethernet
> +                          device which will be used by this CPU port for
> +			  passing packets to/from the host. If not present,
> +			  the port will use the "dsa,ethernet" property
> +			  defined above.

This appears to be for the old binding. The new binding has this
already.  I only want to support multiple CPU ports with the new
binding, since Florian is in the process of removing the old one.

> +
> +- cpu			: Option for non "cpu"/"dsa" ports. A phandle to a
> +			  "cpu" port, which will be used for passing packets
> +			  from this port to the host. If not present, the first
> +			  "cpu" port will be used.
> +
> +
>  Optional subnodes:
>  - fixed-link		: Fixed-link subnode describing a link to a non-MDIO
>  			  managed entity. See
>  			  Documentation/devicetree/bindings/net/fixed-link.txt
>  			  for details.
>  
> -Example:
> +Examples:
>  
>  	dsa@0 {
>  		compatible = "marvell,dsa";
> @@ -416,3 +428,56 @@ Example:
>  			};
>  		};
>  	};
> +
> +	dsa@1 {
> +		compatible = "marvell,dsa";
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		dsa,ethernet = <&eth0port>;
> +		dsa,mii-bus = <&mdio>;
> +
> +		switch@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0 0>;	/* MDIO address 0, switch 0 in tree */
> +
> +			port@0 {
> +				reg = <0>;
> +				label = "lan4";
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				label = "lan3";
> +				cpu = <&cpu1>;
> +			};

Again, this is the old binding. The example should use the new
binding.

Thanks
	Andrew