Subject: Re: [PATCH NET V5 2/2] net: hns: Use phy_driver to setup Phy loopback

From: Andrew Lunn <[email-masked]>
Date: Mon, 26 Jun 2017 15:42:35 +0200

On Mon, Jun 26, 2017 at 10:10:39AM +0800, Lin Yun Sheng wrote:
> Use function set_loopback in phy_driver to setup phy loopback
> when doing ethtool self test.
> 
> Signed-off-by: Lin Yun Sheng <[email-masked]>
> ---
>  drivers/net/ethernet/hisilicon/hns/hnae.h        |  1 +
>  drivers/net/ethernet/hisilicon/hns/hns_ethtool.c | 92 +++++++-----------------
>  2 files changed, 26 insertions(+), 67 deletions(-)
> 
> diff --git a/drivers/net/ethernet/hisilicon/hns/hnae.h b/drivers/net/ethernet/hisilicon/hns/hnae.h
> index 04211ac..7ba653a 100644
> --- a/drivers/net/ethernet/hisilicon/hns/hnae.h
> +++ b/drivers/net/ethernet/hisilicon/hns/hnae.h
> @@ -360,6 +360,7 @@ enum hnae_loop {
>  	MAC_INTERNALLOOP_MAC = 0,
>  	MAC_INTERNALLOOP_SERDES,
>  	MAC_INTERNALLOOP_PHY,
> +	MAC_LOOP_PHY_NONE,
>  	MAC_LOOP_NONE,
>  };
>  
> diff --git a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
> index e95795b..10d82df 100644
> --- a/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
> +++ b/drivers/net/ethernet/hisilicon/hns/hns_ethtool.c
> @@ -259,67 +259,24 @@ static int hns_nic_set_link_ksettings(struct net_device *net_dev,
>  
>  static int hns_nic_config_phy_loopback(struct phy_device *phy_dev, u8 en)
>  {
> -#define COPPER_CONTROL_REG 0
> -#define PHY_POWER_DOWN BIT(11)
> -#define PHY_LOOP_BACK BIT(14)
> -	u16 val = 0;
> -
> -	if (phy_dev->is_c45) /* c45 branch adding for XGE PHY */
> -		return -ENOTSUPP;
> +	int err;
>  
>  	if (en) {
> -		/* speed : 1000M */
> -		phy_write(phy_dev, HNS_PHY_PAGE_REG, 2);
> -		phy_write(phy_dev, 21, 0x1046);
> -
> -		phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
> -		/* Force Master */
> -		phy_write(phy_dev, 9, 0x1F00);
> -
> -		/* Soft-reset */
> -		phy_write(phy_dev, 0, 0x9140);
> -		/* If autoneg disabled,two soft-reset operations */
> -		phy_write(phy_dev, 0, 0x9140);
> -
> -		phy_write(phy_dev, HNS_PHY_PAGE_REG, 0xFA);
> -
> -		/* Default is 0x0400 */
> -		phy_write(phy_dev, 1, 0x418);
> -
> -		/* Force 1000M Link, Default is 0x0200 */
> -		phy_write(phy_dev, 7, 0x20C);
> -
> -		/* Powerup Fiber */
> -		phy_write(phy_dev, HNS_PHY_PAGE_REG, 1);
> -		val = phy_read(phy_dev, COPPER_CONTROL_REG);
> -		val &= ~PHY_POWER_DOWN;
> -		phy_write(phy_dev, COPPER_CONTROL_REG, val);
> -
> -		/* Enable Phy Loopback */
> -		phy_write(phy_dev, HNS_PHY_PAGE_REG, 0);
> -		val = phy_read(phy_dev, COPPER_CONTROL_REG);
> -		val |= PHY_LOOP_BACK;
> -		val &= ~PHY_POWER_DOWN;
> -		phy_write(phy_dev, COPPER_CONTROL_REG, val);
> +		err = phy_resume(phy_dev);

Maybe this was discussed with an earlier version of these patches. Why
are using phy_resume() and phy_suspend()?

>  static int __lb_setup(struct net_device *ndev,
> @@ -332,10 +289,8 @@ static int __lb_setup(struct net_device *ndev,
>  
>  	switch (loop) {
>  	case MAC_INTERNALLOOP_PHY:
> -		if ((phy_dev) && (!phy_dev->is_c45)) {
> -			ret = hns_nic_config_phy_loopback(phy_dev, 0x1);
> -			ret |= h->dev->ops->set_loopback(h, loop, 0x1);
> -		}
> +		ret = hns_nic_config_phy_loopback(phy_dev, 0x1);
> +		ret |= h->dev->ops->set_loopback(h, loop, 0x1);

Or'ing together two errno values does not make much sense:

> +	if (loop == MAC_INTERNALLOOP_PHY)
> +		ret = __lb_setup(ndev, MAC_LOOP_PHY_NONE);
> +	else
> +		ret = __lb_setup(ndev, MAC_LOOP_NONE);
>  	if (ret)
>  		netdev_err(ndev, "%s: __lb_setup return error(%d)!\n",
>  			   __func__,

And it looks like you even print the OR'ed version here!

    Andrew