Subject: Re: [PATCH] net: add support for STMicroelectronics Ethernet controllers.

From: Giuseppe CAVALLARO <[email-masked]>
Date: Wed, 14 Oct 2009 08:58:27 +0200

Eric Dumazet wrote:
> I reviewed your code and found no obvious issues
> 
> Could you please avoid defining this
> 
> #define STMMAC_IP_ALIGN NET_IP_ALIGN
> 
> (I see tg3.c uses a similar TG3_RAW_IP_ALIGN, this is probably why you felt it was necessary :
> In case of tg3, TG3_RAW_IP_ALIGN is used in cases where we always want to align the
> IP/network header on dword boundaries, even on platforms where NET_IP_ALIGN)
> 
> I am not sure this is what you want for STM.
> 
> In that case, please check new netdev_alloc_skb_ip_align() helper

Hi Eric,

Yep, I like that. I've both removed the STMMAC_IP_ALIGN and used the
netdev_alloc_skb_ip_align in the new patch attached.

Regards,
Peppe
>>From d370c0d34c2cfe20de94c05e243ab761e316ab4d Mon Sep 17 00:00:00 2001
From: Giuseppe Cavallaro <[email-masked]>
Date: Mon, 12 Oct 2009 11:11:06 +0200
Subject: [PATCH] net: add support for STMicroelectronics Ethernet controllers.

This is the driver for the ST MAC 10/100/1000 on-chip Ethernet
controllers (Synopsys IP blocks).

Driver documentation:
 o http://stlinux.com/drupal/kernel/network/stmmac
Revisions:
 o http://stlinux.com/drupal/kernel/network/stmmac-driver-revisions
Performances:
 o http://stlinux.com/drupal/benchmarks/networking/stmmac

Signed-off-by: Giuseppe Cavallaro <[email-masked]>
---
 drivers/net/Kconfig                 |    2 +
 drivers/net/Makefile                |    1 +
 drivers/net/stmmac/Kconfig          |   53 +
 drivers/net/stmmac/Makefile         |    4 +
 drivers/net/stmmac/common.h         |  330 ++++++
 drivers/net/stmmac/descs.h          |  163 +++
 drivers/net/stmmac/gmac.c           |  693 +++++++++++
 drivers/net/stmmac/gmac.h           |  204 ++++
 drivers/net/stmmac/mac100.c         |  517 ++++++++
 drivers/net/stmmac/mac100.h         |  116 ++
 drivers/net/stmmac/stmmac.h         |   98 ++
 drivers/net/stmmac/stmmac_ethtool.c |  395 +++++++
 drivers/net/stmmac/stmmac_main.c    | 2204 +++++++++++++++++++++++++++++++++++
 drivers/net/stmmac/stmmac_mdio.c    |  217 ++++
 drivers/net/stmmac/stmmac_timer.c   |  140 +++
 drivers/net/stmmac/stmmac_timer.h   |   41 +
 16 files changed, 5178 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/stmmac/Kconfig
 create mode 100644 drivers/net/stmmac/Makefile
 create mode 100644 drivers/net/stmmac/common.h
 create mode 100644 drivers/net/stmmac/descs.h
 create mode 100644 drivers/net/stmmac/gmac.c
 create mode 100644 drivers/net/stmmac/gmac.h
 create mode 100644 drivers/net/stmmac/mac100.c
 create mode 100644 drivers/net/stmmac/mac100.h
 create mode 100644 drivers/net/stmmac/stmmac.h
 create mode 100644 drivers/net/stmmac/stmmac_ethtool.c
 create mode 100644 drivers/net/stmmac/stmmac_main.c
 create mode 100644 drivers/net/stmmac/stmmac_mdio.c
 create mode 100644 drivers/net/stmmac/stmmac_timer.c
 create mode 100644 drivers/net/stmmac/stmmac_timer.h

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 7127760..e86c95b 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2482,6 +2482,8 @@ config S6GMAC
 	  To compile this driver as a module, choose M here. The module
 	  will be called s6gmac.
 
+source "drivers/net/stmmac/Kconfig"
+
 endif # NETDEV_1000
 
 #
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index d866b8c..e41c553 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -95,6 +95,7 @@ obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
 obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
 obj-$(CONFIG_RIONET) += rionet.o
 obj-$(CONFIG_SH_ETH) += sh_eth.o
+obj-$(CONFIG_STMMAC_ETH) += stmmac/
 
 #
 # end link order section
diff --git a/drivers/net/stmmac/Kconfig b/drivers/net/stmmac/Kconfig
new file mode 100644
index 0000000..35eaa52
--- /dev/null
+++ b/drivers/net/stmmac/Kconfig
@@ -0,0 +1,53 @@
+config STMMAC_ETH
+	tristate "STMicroelectronics 10/100/1000 Ethernet driver"
+	select MII
+	select PHYLIB
+	depends on NETDEVICES && CPU_SUBTYPE_ST40
+	help
+	  This is the driver for the ST MAC 10/100/1000 on-chip Ethernet
+	  controllers. ST Ethernet IPs are built around a Synopsys IP Core.
+
+if STMMAC_ETH
+
+config STMMAC_DA
+	bool "STMMAC DMA arbitration scheme"
+	default n
+	help
+	  Selecting this option, rx has priority over Tx (only for Giga
+	  Ethernet device).
+	  By default, the DMA arbitration scheme is based on Round-robin
+	  (rx:tx priority is 1:1).
+
+config STMMAC_DUAL_MAC
+	bool "STMMAC: dual mac support (EXPERIMENTAL)"
+	default n
+        depends on EXPERIMENTAL && STMMAC_ETH && !STMMAC_TIMER
+	help
+	  Some ST SoCs (for example the stx7141 and stx7200c2) have two
+	  Ethernet Controllers. This option turns on the second Ethernet
+	  device on this kind of platforms.
+
+config STMMAC_TIMER
+	bool "STMMAC Timer optimisation"
+	default n
+	help
+	  Use an external timer for mitigating the number of network
+	  interrupts.
+
+choice
+        prompt "Select Timer device"
+        depends on STMMAC_TIMER
+
+config STMMAC_TMU_TIMER
+        bool "TMU channel 2"
+        depends on CPU_SH4
+	help
+
+config STMMAC_RTC_TIMER
+        bool "Real time clock"
+        depends on RTC_CLASS
+	help
+
+endchoice
+
+endif
diff --git a/drivers/net/stmmac/Makefile b/drivers/net/stmmac/Makefile
new file mode 100644
index 0000000..b2d7a55
--- /dev/null
+++ b/drivers/net/stmmac/Makefile
@@ -0,0 +1,4 @@
+obj-$(CONFIG_STMMAC_ETH) += stmmac.o
+stmmac-$(CONFIG_STMMAC_TIMER) += stmmac_timer.o
+stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o \
+		mac100.o  gmac.o $(stmmac-y)
diff --git a/drivers/net/stmmac/common.h b/drivers/net/stmmac/common.h
new file mode 100644
index 0000000..e49e518
--- /dev/null
+++ b/drivers/net/stmmac/common.h
@@ -0,0 +1,330 @@
+/*******************************************************************************
+  STMMAC Common Header File
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#include "descs.h"
+#include <linux/io.h>
+
+/* *********************************************
+   DMA CRS Control and Status Register Mapping
+ * *********************************************/
+#define DMA_BUS_MODE		0x00001000	/* Bus Mode */
+#define DMA_XMT_POLL_DEMAND	0x00001004	/* Transmit Poll Demand */
+#define DMA_RCV_POLL_DEMAND	0x00001008	/* Received Poll Demand */
+#define DMA_RCV_BASE_ADDR	0x0000100c	/* Receive List Base */
+#define DMA_TX_BASE_ADDR	0x00001010	/* Transmit List Base */
+#define DMA_STATUS		0x00001014	/* Status Register */
+#define DMA_CONTROL		0x00001018	/* Ctrl (Operational Mode) */
+#define DMA_INTR_ENA		0x0000101c	/* Interrupt Enable */
+#define DMA_MISSED_FRAME_CTR	0x00001020	/* Missed Frame Counter */
+#define DMA_CUR_TX_BUF_ADDR	0x00001050	/* Current Host Tx Buffer */
+#define DMA_CUR_RX_BUF_ADDR	0x00001054	/* Current Host Rx Buffer */
+
+/* ********************************
+   DMA Control register defines
+ * ********************************/
+#define DMA_CONTROL_ST		0x00002000	/* Start/Stop Transmission */
+#define DMA_CONTROL_SR		0x00000002	/* Start/Stop Receive */
+
+/* **************************************
+   DMA Interrupt Enable register defines
+ * **************************************/
+/**** NORMAL INTERRUPT ****/
+#define DMA_INTR_ENA_NIE 0x00010000	/* Normal Summary */
+#define DMA_INTR_ENA_TIE 0x00000001	/* Transmit Interrupt */
+#define DMA_INTR_ENA_TUE 0x00000004	/* Transmit Buffer Unavailable */
+#define DMA_INTR_ENA_RIE 0x00000040	/* Receive Interrupt */
+#define DMA_INTR_ENA_ERE 0x00004000	/* Early Receive */
+
+#define DMA_INTR_NORMAL	(DMA_INTR_ENA_NIE | DMA_INTR_ENA_RIE | \
+			DMA_INTR_ENA_TIE)
+
+/**** ABNORMAL INTERRUPT ****/
+#define DMA_INTR_ENA_AIE 0x00008000	/* Abnormal Summary */
+#define DMA_INTR_ENA_FBE 0x00002000	/* Fatal Bus Error */
+#define DMA_INTR_ENA_ETE 0x00000400	/* Early Transmit */
+#define DMA_INTR_ENA_RWE 0x00000200	/* Receive Watchdog */
+#define DMA_INTR_ENA_RSE 0x00000100	/* Receive Stopped */
+#define DMA_INTR_ENA_RUE 0x00000080	/* Receive Buffer Unavailable */
+#define DMA_INTR_ENA_UNE 0x00000020	/* Tx Underflow */
+#define DMA_INTR_ENA_OVE 0x00000010	/* Receive Overflow */
+#define DMA_INTR_ENA_TJE 0x00000008	/* Transmit Jabber */
+#define DMA_INTR_ENA_TSE 0x00000002	/* Transmit Stopped */
+
+#define DMA_INTR_ABNORMAL	(DMA_INTR_ENA_AIE | DMA_INTR_ENA_FBE | \
+				DMA_INTR_ENA_UNE)
+
+/* DMA default interrupt mask */
+#define DMA_INTR_DEFAULT_MASK	(DMA_INTR_NORMAL | DMA_INTR_ABNORMAL)
+
+/* ****************************
+ *  DMA Status register defines
+ * ****************************/
+#define DMA_STATUS_GPI		0x10000000	/* PMT interrupt */
+#define DMA_STATUS_GMI		0x08000000	/* MMC interrupt */
+#define DMA_STATUS_GLI		0x04000000	/* GMAC Line interface int. */
+#define DMA_STATUS_GMI		0x08000000
+#define DMA_STATUS_GLI		0x04000000
+#define DMA_STATUS_EB_MASK	0x00380000	/* Error Bits Mask */
+#define DMA_STATUS_EB_TX_ABORT	0x00080000	/* Error Bits - TX Abort */
+#define DMA_STATUS_EB_RX_ABORT	0x00100000	/* Error Bits - RX Abort */
+#define DMA_STATUS_TS_MASK	0x00700000	/* Transmit Process State */
+#define DMA_STATUS_TS_SHIFT	20
+#define DMA_STATUS_RS_MASK	0x000e0000	/* Receive Process State */
+#define DMA_STATUS_RS_SHIFT	17
+#define DMA_STATUS_NIS	0x00010000	/* Normal Interrupt Summary */
+#define DMA_STATUS_AIS	0x00008000	/* Abnormal Interrupt Summary */
+#define DMA_STATUS_ERI	0x00004000	/* Early Receive Interrupt */
+#define DMA_STATUS_FBI	0x00002000	/* Fatal Bus Error Interrupt */
+#define DMA_STATUS_ETI	0x00000400	/* Early Transmit Interrupt */
+#define DMA_STATUS_RWT	0x00000200	/* Receive Watchdog Timeout */
+#define DMA_STATUS_RPS	0x00000100	/* Receive Process Stopped */
+#define DMA_STATUS_RU	0x00000080	/* Receive Buffer Unavailable */
+#define DMA_STATUS_RI	0x00000040	/* Receive Interrupt */
+#define DMA_STATUS_UNF	0x00000020	/* Transmit Underflow */
+#define DMA_STATUS_OVF	0x00000010	/* Receive Overflow */
+#define DMA_STATUS_TJT	0x00000008	/* Transmit Jabber Timeout */
+#define DMA_STATUS_TU	0x00000004	/* Transmit Buffer Unavailable */
+#define DMA_STATUS_TPS	0x00000002	/* Transmit Process Stopped */
+#define DMA_STATUS_TI	0x00000001	/* Transmit Interrupt */
+
+/* Other defines */
+#define HASH_TABLE_SIZE 64
+#define PAUSE_TIME 0x200
+
+/* Flow Control defines */
+#define FLOW_OFF	0
+#define FLOW_RX		1
+#define FLOW_TX		2
+#define FLOW_AUTO	(FLOW_TX | FLOW_RX)
+
+/* DMA STORE-AND-FORWARD Operation Mode */
+#define SF_DMA_MODE 1
+
+#define HW_CSUM 1
+#define NO_HW_CSUM 0
+
+/* GMAC TX FIFO is 8K, Rx FIFO is 16K */
+#define BUF_SIZE_16KiB 16384
+#define BUF_SIZE_8KiB 8192
+#define BUF_SIZE_4KiB 4096
+#define BUF_SIZE_2KiB 2048
+
+/* Power Down and WOL */
+#define PMT_NOT_SUPPORTED 0
+#define PMT_SUPPORTED 1
+
+/* Common MAC defines */
+#define MAC_CTRL_REG		0x00000000	/* MAC Control */
+#define MAC_ENABLE_TX		0x00000008	/* Transmitter Enable */
+#define MAC_RNABLE_RX		0x00000004	/* Receiver Enable */
+
+/* MAC Management Counters register */
+#define MMC_CONTROL		0x00000100	/* MMC Control */
+#define MMC_HIGH_INTR		0x00000104	/* MMC High Interrupt */
+#define MMC_LOW_INTR		0x00000108	/* MMC Low Interrupt */
+#define MMC_HIGH_INTR_MASK	0x0000010c	/* MMC High Interrupt Mask */
+#define MMC_LOW_INTR_MASK	0x00000110	/* MMC Low Interrupt Mask */
+
+#define MMC_CONTROL_MAX_FRM_MASK	0x0003ff8	/* Maximum Frame Size */
+#define MMC_CONTROL_MAX_FRM_SHIFT	3
+#define MMC_CONTROL_MAX_FRAME		0x7FF
+
+struct stmmac_extra_stats {
+	/* Transmit errors */
+	unsigned long tx_underflow ____cacheline_aligned;
+	unsigned long tx_carrier;
+	unsigned long tx_losscarrier;
+	unsigned long tx_heartbeat;
+	unsigned long tx_deferred;
+	unsigned long tx_vlan;
+	unsigned long tx_jabber;
+	unsigned long tx_frame_flushed;
+	unsigned long tx_payload_error;
+	unsigned long tx_ip_header_error;
+	/* Receive errors */
+	unsigned long rx_desc;
+	unsigned long rx_partial;
+	unsigned long rx_runt;
+	unsigned long rx_toolong;
+	unsigned long rx_collision;
+	unsigned long rx_crc;
+	unsigned long rx_lenght;
+	unsigned long rx_mii;
+	unsigned long rx_multicast;
+	unsigned long rx_gmac_overflow;
+	unsigned long rx_watchdog;
+	unsigned long da_rx_filter_fail;
+	unsigned long sa_rx_filter_fail;
+	unsigned long rx_missed_cntr;
+	unsigned long rx_overflow_cntr;
+	unsigned long rx_vlan;
+	/* Tx/Rx IRQ errors */
+	unsigned long tx_undeflow_irq;
+	unsigned long tx_process_stopped_irq;
+	unsigned long tx_jabber_irq;
+	unsigned long rx_overflow_irq;
+	unsigned long rx_buf_unav_irq;
+	unsigned long rx_process_stopped_irq;
+	unsigned long rx_watchdog_irq;
+	unsigned long tx_early_irq;
+	unsigned long fatal_bus_error_irq;
+	/* Extra info */
+	unsigned long threshold;
+	unsigned long tx_pkt_n;
+	unsigned long rx_pkt_n;
+	unsigned long poll_n;
+	unsigned long sched_timer_n;
+	unsigned long normal_irq_n;
+};
+
+/* GMAC core can compute the checksums in HW. */
+enum rx_frame_status {
+	good_frame = 0,
+	discard_frame = 1,
+	csum_none = 2,
+};
+
+static inline void stmmac_set_mac_addr(unsigned long ioaddr, u8 addr[6],
+			 unsigned int high, unsigned int low)
+{
+	unsigned long data;
+
+	data = (addr[5] << 8) | addr[4];
+	writel(data, ioaddr + high);
+	data = (addr[3] << 24) | (addr[2] << 16) | (addr[1] << 8) | addr[0];
+	writel(data, ioaddr + low);
+
+	return;
+}
+
+static inline void stmmac_get_mac_addr(unsigned long ioaddr,
+				unsigned char *addr, unsigned int high,
+				unsigned int low)
+{
+	unsigned int hi_addr, lo_addr;
+
+	/* Read the MAC address from the hardware */
+	hi_addr = readl(ioaddr + high);
+	lo_addr = readl(ioaddr + low);
+
+	/* Extract the MAC address from the high and low words */
+	addr[0] = lo_addr & 0xff;
+	addr[1] = (lo_addr >> 8) & 0xff;
+	addr[2] = (lo_addr >> 16) & 0xff;
+	addr[3] = (lo_addr >> 24) & 0xff;
+	addr[4] = hi_addr & 0xff;
+	addr[5] = (hi_addr >> 8) & 0xff;
+
+	return;
+}
+
+struct stmmac_ops {
+	/* MAC core initialization */
+	void (*core_init) (unsigned long ioaddr) ____cacheline_aligned;
+	/* DMA core initialization */
+	int (*dma_init) (unsigned long ioaddr, int pbl, u32 dma_tx, u32 dma_rx);
+	/* Dump MAC registers */
+	void (*dump_mac_regs) (unsigned long ioaddr);
+	/* Dump DMA registers */
+	void (*dump_dma_regs) (unsigned long ioaddr);
+	/* Set tx/rx threshold in the csr6 register
+	 * An invalid value enables the store-and-forward mode */
+	void (*dma_mode) (unsigned long ioaddr, int txmode, int rxmode);
+	/* To track extra statistic (if supported) */
+	void (*dma_diagnostic_fr) (void *data, struct stmmac_extra_stats *x,
+				   unsigned long ioaddr);
+	/* RX descriptor ring initialization */
+	void (*init_rx_desc) (struct dma_desc *p, unsigned int ring_size,
+				int disable_rx_ic);
+	/* TX descriptor ring initialization */
+	void (*init_tx_desc) (struct dma_desc *p, unsigned int ring_size);
+
+	/* Invoked by the xmit function to prepare the tx descriptor */
+	void (*prepare_tx_desc) (struct dma_desc *p, int is_fs, int len,
+				 int csum_flag);
+	/* Set/get the owner of the descriptor */
+	void (*set_tx_owner) (struct dma_desc *p);
+	int (*get_tx_owner) (struct dma_desc *p);
+	/* Invoked by the xmit function to close the tx descriptor */
+	void (*close_tx_desc) (struct dma_desc *p);
+	/* Clean the tx descriptor as soon as the tx irq is received */
+	void (*release_tx_desc) (struct dma_desc *p);
+	/* Clear interrupt on tx frame completion. When this bit is
+	 * set an interrupt happens as soon as the frame is transmitted */
+	void (*clear_tx_ic) (struct dma_desc *p);
+	/* Last tx segment reports the transmit status */
+	int (*get_tx_ls) (struct dma_desc *p);
+	/* Return the transmit status looking at the TDES1 */
+	int (*tx_status) (void *data, struct stmmac_extra_stats *x,
+			  struct dma_desc *p, unsigned long ioaddr);
+	/* Get the buffer size from the descriptor */
+	int (*get_tx_len) (struct dma_desc *p);
+	/* Handle extra events on specific interrupts hw dependent */
+	void (*host_irq_status) (unsigned long ioaddr);
+	int (*get_rx_owner) (struct dma_desc *p);
+	void (*set_rx_owner) (struct dma_desc *p);
+	/* Get the receive frame size */
+	int (*get_rx_frame_len) (struct dma_desc *p);
+	/* Return the reception status looking at the RDES1 */
+	int (*rx_status) (void *data, struct stmmac_extra_stats *x,
+			  struct dma_desc *p);
+	/* Multicast filter setting */
+	void (*set_filter) (struct net_device *dev);
+	/* Flow control setting */
+	void (*flow_ctrl) (unsigned long ioaddr, unsigned int duplex,
+			   unsigned int fc, unsigned int pause_time);
+	/* Set power management mode (e.g. magic frame) */
+	void (*pmt) (unsigned long ioaddr, unsigned long mode);
+	/* Set/Get Unicast MAC addresses */
+	void (*set_umac_addr) (unsigned long ioaddr, unsigned char *addr,
+			     unsigned int reg_n);
+	void (*get_umac_addr) (unsigned long ioaddr, unsigned char *addr,
+			     unsigned int reg_n);
+};
+
+struct mac_link {
+	int port;
+	int duplex;
+	int speed;
+};
+
+struct mii_regs {
+	unsigned int addr;	/* MII Address */
+	unsigned int data;	/* MII Data */
+};
+
+struct hw_cap {
+	unsigned int version;	/* Core Version register (GMAC) */
+	unsigned int pmt;	/* Power-Down mode (GMAC) */
+	struct mac_link link;
+	struct mii_regs mii;
+};
+
+struct mac_device_info {
+	struct hw_cap hw;
+	struct stmmac_ops *ops;
+};
+
+struct mac_device_info *gmac_setup(unsigned long addr);
+struct mac_device_info *mac100_setup(unsigned long addr);
diff --git a/drivers/net/stmmac/descs.h b/drivers/net/stmmac/descs.h
new file mode 100644
index 0000000..6d2a0b2
--- /dev/null
+++ b/drivers/net/stmmac/descs.h
@@ -0,0 +1,163 @@
+/*******************************************************************************
+  Header File to describe the DMA descriptors
+  Use enhanced descriptors in case of GMAC Cores.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+struct dma_desc {
+	/* Receive descriptor */
+	union {
+		struct {
+			/* RDES0 */
+			u32 reserved1:1;
+			u32 crc_error:1;
+			u32 dribbling:1;
+			u32 mii_error:1;
+			u32 receive_watchdog:1;
+			u32 frame_type:1;
+			u32 collision:1;
+			u32 frame_too_long:1;
+			u32 last_descriptor:1;
+			u32 first_descriptor:1;
+			u32 multicast_frame:1;
+			u32 run_frame:1;
+			u32 length_error:1;
+			u32 partial_frame_error:1;
+			u32 descriptor_error:1;
+			u32 error_summary:1;
+			u32 frame_length:14;
+			u32 filtering_fail:1;
+			u32 own:1;
+			/* RDES1 */
+			u32 buffer1_size:11;
+			u32 buffer2_size:11;
+			u32 reserved2:2;
+			u32 second_address_chained:1;
+			u32 end_ring:1;
+			u32 reserved3:5;
+			u32 disable_ic:1;
+		} rx;
+		struct {
+			/* RDES0 */
+			u32 payload_csum_error:1;
+			u32 crc_error:1;
+			u32 dribbling:1;
+			u32 error_gmii:1;
+			u32 receive_watchdog:1;
+			u32 frame_type:1;
+			u32 late_collision:1;
+			u32 ipc_csum_error:1;
+			u32 last_descriptor:1;
+			u32 first_descriptor:1;
+			u32 vlan_tag:1;
+			u32 overflow_error:1;
+			u32 length_error:1;
+			u32 sa_filter_fail:1;
+			u32 descriptor_error:1;
+			u32 error_summary:1;
+			u32 frame_length:14;
+			u32 da_filter_fail:1;
+			u32 own:1;
+			/* RDES1 */
+			u32 buffer1_size:13;
+			u32 reserved1:1;
+			u32 second_address_chained:1;
+			u32 end_ring:1;
+			u32 buffer2_size:13;
+			u32 reserved2:2;
+			u32 disable_ic:1;
+		} erx;		/* -- enhanced -- */
+
+		/* Transmit descriptor */
+		struct {
+			/* TDES0 */
+			u32 deferred:1;
+			u32 underflow_error:1;
+			u32 excessive_deferral:1;
+			u32 collision_count:4;
+			u32 heartbeat_fail:1;
+			u32 excessive_collisions:1;
+			u32 late_collision:1;
+			u32 no_carrier:1;
+			u32 loss_carrier:1;
+			u32 reserved1:3;
+			u32 error_summary:1;
+			u32 reserved2:15;
+			u32 own:1;
+			/* TDES1 */
+			u32 buffer1_size:11;
+			u32 buffer2_size:11;
+			u32 reserved3:1;
+			u32 disable_padding:1;
+			u32 second_address_chained:1;
+			u32 end_ring:1;
+			u32 crc_disable:1;
+			u32 reserved4:2;
+			u32 first_segment:1;
+			u32 last_segment:1;
+			u32 interrupt:1;
+		} tx;
+		struct {
+			/* TDES0 */
+			u32 deferred:1;
+			u32 underflow_error:1;
+			u32 excessive_deferral:1;
+			u32 collision_count:4;
+			u32 vlan_frame:1;
+			u32 excessive_collisions:1;
+			u32 late_collision:1;
+			u32 no_carrier:1;
+			u32 loss_carrier:1;
+			u32 payload_error:1;
+			u32 frame_flushed:1;
+			u32 jabber_timeout:1;
+			u32 error_summary:1;
+			u32 ip_header_error:1;
+			u32 time_stamp_status:1;
+			u32 reserved1:2;
+			u32 second_address_chained:1;
+			u32 end_ring:1;
+			u32 checksum_insertion:2;
+			u32 reserved2:1;
+			u32 time_stamp_enable:1;
+			u32 disable_padding:1;
+			u32 crc_disable:1;
+			u32 first_segment:1;
+			u32 last_segment:1;
+			u32 interrupt:1;
+			u32 own:1;
+			/* TDES1 */
+			u32 buffer1_size:13;
+			u32 reserved3:3;
+			u32 buffer2_size:13;
+			u32 reserved4:3;
+		} etx;		/* -- enhanced -- */
+	} des01;
+	unsigned int des2;
+	unsigned int des3;
+};
+
+/* Transmit checksum insertion control */
+enum tdes_csum_insertion {
+	cic_disabled = 0,	/* Checksum Insertion Control */
+	cic_only_ip = 1,	/* Only IP header */
+	cic_no_pseudoheader = 2,	/* IP header but pseudoheader
+					 * is not calculated */
+	cic_full = 3,		/* IP header and pseudoheader */
+};
diff --git a/drivers/net/stmmac/gmac.c b/drivers/net/stmmac/gmac.c
new file mode 100644
index 0000000..b624bb5
--- /dev/null
+++ b/drivers/net/stmmac/gmac.c
@@ -0,0 +1,693 @@
+/*******************************************************************************
+  This is the driver for the GMAC on-chip Ethernet controller for ST SoCs.
+  DWC Ether MAC 10/100/1000 Universal version 3.41a  has been used for
+  developing this code.
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#include <linux/netdevice.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include "stmmac.h"
+#include "gmac.h"
+
+#undef GMAC_DEBUG
+/*#define GMAC_DEBUG*/
+#undef FRAME_FILTER_DEBUG
+/*#define FRAME_FILTER_DEBUG*/
+#ifdef GMAC_DEBUG
+#define DBG(fmt, args...)  printk(fmt, ## args)
+#else
+#define DBG(fmt, args...)  do { } while (0)
+#endif
+
+static void gmac_dump_regs(unsigned long ioaddr)
+{
+	int i;
+	pr_info("\t----------------------------------------------\n"
+	       "\t  GMAC registers (base addr = 0x%8x)\n"
+	       "\t----------------------------------------------\n",
+	       (unsigned int)ioaddr);
+
+	for (i = 0; i < 55; i++) {
+		int offset = i * 4;
+		pr_info("\tReg No. %d (offset 0x%x): 0x%08x\n", i,
+		       offset, readl(ioaddr + offset));
+	}
+	return;
+}
+
+static int gmac_dma_init(unsigned long ioaddr, int pbl, u32 dma_tx, u32 dma_rx)
+{
+	u32 value = readl(ioaddr + DMA_BUS_MODE);
+	/* DMA SW reset */
+	value |= DMA_BUS_MODE_SFT_RESET;
+	writel(value, ioaddr + DMA_BUS_MODE);
+	do {} while ((readl(ioaddr + DMA_BUS_MODE) & DMA_BUS_MODE_SFT_RESET));
+
+	value = /* DMA_BUS_MODE_FB | */ DMA_BUS_MODE_4PBL |
+	    ((pbl << DMA_BUS_MODE_PBL_SHIFT) |
+	     (pbl << DMA_BUS_MODE_RPBL_SHIFT));
+
+#ifdef CONFIG_STMMAC_DA
+	value |= DMA_BUS_MODE_DA;	/* Rx has priority over tx */
+#endif
+	writel(value, ioaddr + DMA_BUS_MODE);
+
+	/* Mask interrupts by writing to CSR7 */
+	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
+
+	/* The base address of the RX/TX descriptor lists must be written into
+	 * DMA CSR3 and CSR4, respectively. */
+	writel(dma_tx, ioaddr + DMA_TX_BASE_ADDR);
+	writel(dma_rx, ioaddr + DMA_RCV_BASE_ADDR);
+
+	return 0;
+}
+
+/* Transmit FIFO flush operation */
+static void gmac_flush_tx_fifo(unsigned long ioaddr)
+{
+	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+	writel((csr6 | DMA_CONTROL_FTF), ioaddr + DMA_CONTROL);
+
+	do {} while ((readl(ioaddr + DMA_CONTROL) & DMA_CONTROL_FTF));
+}
+
+static void gmac_dma_operation_mode(unsigned long ioaddr, int txmode,
+				    int rxmode)
+{
+	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+
+	if (txmode == SF_DMA_MODE) {
+		DBG(KERN_DEBUG "GMAC: enabling TX store and forward mode\n");
+		/* Transmit COE type 2 cannot be done in cut-through mode. */
+		csr6 |= DMA_CONTROL_TSF;
+		/* Operating on second frame increase the performance
+		 * especially when transmit store-and-forward is used.*/
+		csr6 |= DMA_CONTROL_OSF;
+	} else {
+		DBG(KERN_DEBUG "GMAC: disabling TX store and forward mode"
+			      " (threshold = %d)\n", txmode);
+		csr6 &= ~DMA_CONTROL_TSF;
+		csr6 &= DMA_CONTROL_TC_TX_MASK;
+		/* Set the transmit threashold */
+		if (txmode <= 32)
+			csr6 |= DMA_CONTROL_TTC_32;
+		else if (txmode <= 64)
+			csr6 |= DMA_CONTROL_TTC_64;
+		else if (txmode <= 128)
+			csr6 |= DMA_CONTROL_TTC_128;
+		else if (txmode <= 192)
+			csr6 |= DMA_CONTROL_TTC_192;
+		else
+			csr6 |= DMA_CONTROL_TTC_256;
+	}
+
+	if (rxmode == SF_DMA_MODE) {
+		DBG(KERN_DEBUG "GMAC: enabling RX store and forward mode\n");
+		csr6 |= DMA_CONTROL_RSF;
+	} else {
+		DBG(KERN_DEBUG "GMAC: disabling RX store and forward mode"
+			      " (threshold = %d)\n", rxmode);
+		csr6 &= ~DMA_CONTROL_RSF;
+		csr6 &= DMA_CONTROL_TC_RX_MASK;
+		if (rxmode <= 32)
+			csr6 |= DMA_CONTROL_RTC_32;
+		else if (rxmode <= 64)
+			csr6 |= DMA_CONTROL_RTC_64;
+		else if (rxmode <= 96)
+			csr6 |= DMA_CONTROL_RTC_96;
+		else
+			csr6 |= DMA_CONTROL_RTC_128;
+	}
+
+	writel(csr6, ioaddr + DMA_CONTROL);
+	return;
+}
+
+/* Not yet implemented --- no RMON module */
+static void gmac_dma_diagnostic_fr(void *data, struct stmmac_extra_stats *x,
+				   unsigned long ioaddr)
+{
+	return;
+}
+
+static void gmac_dump_dma_regs(unsigned long ioaddr)
+{
+	int i;
+	pr_info(" DMA registers\n");
+	for (i = 0; i < 22; i++) {
+		if ((i < 9) || (i > 17)) {
+			int offset = i * 4;
+			pr_err("\t Reg No. %d (offset 0x%x): 0x%08x\n", i,
+			       (DMA_BUS_MODE + offset),
+			       readl(ioaddr + DMA_BUS_MODE + offset));
+		}
+	}
+	return;
+}
+
+static int gmac_get_tx_frame_status(void *data, struct stmmac_extra_stats *x,
+				    struct dma_desc *p, unsigned long ioaddr)
+{
+	int ret = 0;
+	struct net_device_stats *stats = (struct net_device_stats *)data;
+
+	if (unlikely(p->des01.etx.error_summary)) {
+		DBG(KERN_ERR "GMAC TX error... 0x%08x\n", p->des01.etx);
+		if (unlikely(p->des01.etx.jabber_timeout)) {
+			DBG(KERN_ERR "\tjabber_timeout error\n");
+			x->tx_jabber++;
+		}
+
+		if (unlikely(p->des01.etx.frame_flushed)) {
+			DBG(KERN_ERR "\tframe_flushed error\n");
+			x->tx_frame_flushed++;
+			gmac_flush_tx_fifo(ioaddr);
+		}
+
+		if (unlikely(p->des01.etx.loss_carrier)) {
+			DBG(KERN_ERR "\tloss_carrier error\n");
+			x->tx_losscarrier++;
+			stats->tx_carrier_errors++;
+		}
+		if (unlikely(p->des01.etx.no_carrier)) {
+			DBG(KERN_ERR "\tno_carrier error\n");
+			x->tx_carrier++;
+			stats->tx_carrier_errors++;
+		}
+		if (unlikely(p->des01.etx.late_collision)) {
+			DBG(KERN_ERR "\tlate_collision error\n");
+			stats->collisions += p->des01.etx.collision_count;
+		}
+		if (unlikely(p->des01.etx.excessive_collisions)) {
+			DBG(KERN_ERR "\texcessive_collisions\n");
+			stats->collisions += p->des01.etx.collision_count;
+		}
+		if (unlikely(p->des01.etx.excessive_deferral)) {
+			DBG(KERN_INFO "\texcessive tx_deferral\n");
+			x->tx_deferred++;
+		}
+
+		if (unlikely(p->des01.etx.underflow_error)) {
+			DBG(KERN_ERR "\tunderflow error\n");
+			gmac_flush_tx_fifo(ioaddr);
+			x->tx_underflow++;
+		}
+
+		if (unlikely(p->des01.etx.ip_header_error)) {
+			DBG(KERN_ERR "\tTX IP header csum error\n");
+			x->tx_ip_header_error++;
+		}
+
+		if (unlikely(p->des01.etx.payload_error)) {
+			DBG(KERN_ERR "\tAddr/Payload csum error\n");
+			x->tx_payload_error++;
+			gmac_flush_tx_fifo(ioaddr);
+		}
+
+		ret = -1;
+	}
+
+	if (unlikely(p->des01.etx.deferred)) {
+		DBG(KERN_INFO "GMAC TX status: tx deferred\n");
+		x->tx_deferred++;
+	}
+#ifdef STMMAC_VLAN_TAG_USED
+	if (p->des01.etx.vlan_frame) {
+		DBG(KERN_INFO "GMAC TX status: VLAN frame\n");
+		x->tx_vlan++;
+	}
+#endif
+
+	return ret;
+}
+
+static int gmac_get_tx_len(struct dma_desc *p)
+{
+	return p->des01.etx.buffer1_size;
+}
+
+static int gmac_coe_rdes0(int ipc_err, int type, int payload_err)
+{
+	int ret = good_frame;
+	u32 status = (type << 2 | ipc_err << 1 | payload_err) & 0x7;
+
+	/* bits 5 7 0 | Frame status
+	 * ----------------------------------------------------------
+	 *      0 0 0 | IEEE 802.3 Type frame (lenght < 1536 octects)
+	 *      1 0 0 | IPv4/6 No CSUM errorS.
+	 *      1 0 1 | IPv4/6 CSUM PAYLOAD error
+	 *      1 1 0 | IPv4/6 CSUM IP HR error
+	 *      1 1 1 | IPv4/6 IP PAYLOAD AND HEADER errorS
+	 *      0 0 1 | IPv4/6 unsupported IP PAYLOAD
+	 *      0 1 1 | COE bypassed.. no IPv4/6 frame
+	 *      0 1 0 | Reserved.
+	 */
+	if (status == 0x0) {
+		DBG(KERN_INFO "RX Des0 status: IEEE 802.3 Type frame.\n");
+		ret = good_frame;
+	} else if (status == 0x4) {
+		DBG(KERN_INFO "RX Des0 status: IPv4/6 No CSUM errorS.\n");
+		ret = good_frame;
+	} else if (status == 0x5) {
+		DBG(KERN_ERR "RX Des0 status: IPv4/6 Payload Error.\n");
+		ret = csum_none;
+	} else if (status == 0x6) {
+		DBG(KERN_ERR "RX Des0 status: IPv4/6 Header Error.\n");
+		ret = csum_none;
+	} else if (status == 0x7) {
+		DBG(KERN_ERR
+		    "RX Des0 status: IPv4/6 Header and Payload Error.\n");
+		ret = csum_none;
+	} else if (status == 0x1) {
+		DBG(KERN_ERR
+		    "RX Des0 status: IPv4/6 unsupported IP PAYLOAD.\n");
+		ret = discard_frame;
+	} else if (status == 0x3) {
+		DBG(KERN_ERR "RX Des0 status: No IPv4, IPv6 frame.\n");
+		ret = discard_frame;
+	}
+	return ret;
+}
+
+static int gmac_get_rx_frame_status(void *data, struct stmmac_extra_stats *x,
+				    struct dma_desc *p)
+{
+	int ret = good_frame;
+	struct net_device_stats *stats = (struct net_device_stats *)data;
+
+	if (unlikely(p->des01.erx.error_summary)) {
+		DBG(KERN_ERR "GMAC RX Error Summary... 0x%08x\n", p->des01.erx);
+		if (unlikely(p->des01.erx.descriptor_error)) {
+			DBG(KERN_ERR "\tdescriptor error\n");
+			x->rx_desc++;
+			stats->rx_length_errors++;
+		}
+		if (unlikely(p->des01.erx.overflow_error)) {
+			DBG(KERN_ERR "\toverflow error\n");
+			x->rx_gmac_overflow++;
+		}
+
+		if (unlikely(p->des01.erx.ipc_csum_error))
+			DBG(KERN_ERR "\tIPC Csum Error/Giant frame\n");
+
+		if (unlikely(p->des01.erx.late_collision)) {
+			DBG(KERN_ERR "\tlate_collision error\n");
+			stats->collisions++;
+			stats->collisions++;
+		}
+		if (unlikely(p->des01.erx.receive_watchdog)) {
+			DBG(KERN_ERR "\treceive_watchdog error\n");
+			x->rx_watchdog++;
+		}
+		if (unlikely(p->des01.erx.error_gmii)) {
+			DBG(KERN_ERR "\tReceive Error\n");
+			x->rx_mii++;
+		}
+		if (unlikely(p->des01.erx.crc_error)) {
+			DBG(KERN_ERR "\tCRC error\n");
+			x->rx_crc++;
+			stats->rx_crc_errors++;
+		}
+		ret = discard_frame;
+	}
+
+	/* After a payload csum error, the ES bit is set.
+	 * It doesn't match with the information reported into the databook.
+	 * At any rate, we need to understand if the CSUM hw computation is ok
+	 * and report this info to the upper layers. */
+	ret = gmac_coe_rdes0(p->des01.erx.ipc_csum_error,
+		p->des01.erx.frame_type, p->des01.erx.payload_csum_error);
+
+	if (unlikely(p->des01.erx.dribbling)) {
+		DBG(KERN_ERR "GMAC RX: dribbling error\n");
+		ret = discard_frame;
+	}
+	if (unlikely(p->des01.erx.sa_filter_fail)) {
+		DBG(KERN_ERR "GMAC RX : Source Address filter fail\n");
+		x->sa_rx_filter_fail++;
+		ret = discard_frame;
+	}
+	if (unlikely(p->des01.erx.da_filter_fail)) {
+		DBG(KERN_ERR "GMAC RX : Destination Address filter fail\n");
+		x->da_rx_filter_fail++;
+		ret = discard_frame;
+	}
+	if (unlikely(p->des01.erx.length_error)) {
+		DBG(KERN_ERR "GMAC RX: length_error error\n");
+		x->rx_lenght++;
+		ret = discard_frame;
+	}
+#ifdef STMMAC_VLAN_TAG_USED
+	if (p->des01.erx.vlan_tag) {
+		DBG(KERN_INFO "GMAC RX: VLAN frame tagged\n");
+		x->rx_vlan++;
+	}
+#endif
+	return ret;
+}
+
+static void gmac_irq_status(unsigned long ioaddr)
+{
+	u32 intr_status = readl(ioaddr + GMAC_INT_STATUS);
+
+	/* Not used events (e.g. MMC interrupts) are not handled. */
+	if ((intr_status & mmc_tx_irq))
+		DBG(KERN_DEBUG "GMAC: MMC tx interrupt: 0x%08x\n",
+		    readl(ioaddr + GMAC_MMC_TX_INTR));
+	if (unlikely(intr_status & mmc_rx_irq))
+		DBG(KERN_DEBUG "GMAC: MMC rx interrupt: 0x%08x\n",
+		    readl(ioaddr + GMAC_MMC_RX_INTR));
+	if (unlikely(intr_status & mmc_rx_csum_offload_irq))
+		DBG(KERN_DEBUG "GMAC: MMC rx csum offload: 0x%08x\n",
+		    readl(ioaddr + GMAC_MMC_RX_CSUM_OFFLOAD));
+	if (unlikely(intr_status & pmt_irq)) {
+		DBG(KERN_DEBUG "GMAC: received Magic frame\n");
+		/* clear the PMT bits 5 and 6 by reading the PMT
+		 * status register. */
+		readl(ioaddr + GMAC_PMT);
+	}
+
+	return;
+}
+
+static void gmac_core_init(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + GMAC_CONTROL);
+	value |= GMAC_CORE_INIT;
+	writel(value, ioaddr + GMAC_CONTROL);
+
+	/* STBus Bridge Configuration */
+	/*writel(0xc5608, ioaddr + 0x00007000);*/
+
+	/* Freeze MMC counters */
+	writel(0x8, ioaddr + GMAC_MMC_CTRL);
+	/* Mask GMAC interrupts */
+	writel(0x207, ioaddr + GMAC_INT_MASK);
+
+#ifdef STMMAC_VLAN_TAG_USED
+	/* Tag detection without filtering */
+	writel(0x0, ioaddr + GMAC_VLAN_TAG);
+#endif
+	return;
+}
+
+static void gmac_set_umac_addr(unsigned long ioaddr, unsigned char *addr,
+				unsigned int reg_n)
+{
+	stmmac_set_mac_addr(ioaddr, addr, GMAC_ADDR_HIGH(reg_n),
+				GMAC_ADDR_LOW(reg_n));
+}
+
+static void gmac_get_umac_addr(unsigned long ioaddr, unsigned char *addr,
+				unsigned int reg_n)
+{
+	stmmac_get_mac_addr(ioaddr, addr, GMAC_ADDR_HIGH(reg_n),
+				GMAC_ADDR_LOW(reg_n));
+}
+
+static void gmac_set_filter(struct net_device *dev)
+{
+	unsigned long ioaddr = dev->base_addr;
+	unsigned int value = 0;
+
+	DBG(KERN_INFO "%s: # mcasts %d, # unicast %d\n",
+	    __func__, dev->mc_count, dev->uc_count);
+
+	if (dev->flags & IFF_PROMISC)
+		value = GMAC_FRAME_FILTER_PR;
+	else if ((dev->mc_count > HASH_TABLE_SIZE)
+		   || (dev->flags & IFF_ALLMULTI)) {
+		value = GMAC_FRAME_FILTER_PM;	/* pass all multi */
+		writel(0xffffffff, ioaddr + GMAC_HASH_HIGH);
+		writel(0xffffffff, ioaddr + GMAC_HASH_LOW);
+	} else if (dev->mc_count > 0) {
+		int i;
+		u32 mc_filter[2];
+		struct dev_mc_list *mclist;
+
+		/* Hash filter for multicast */
+		value = GMAC_FRAME_FILTER_HMC;
+
+		memset(mc_filter, 0, sizeof(mc_filter));
+		for (i = 0, mclist = dev->mc_list;
+		     mclist && i < dev->mc_count; i++, mclist = mclist->next) {
+			/* The upper 6 bits of the calculated CRC are used to
+			   index the contens of the hash table */
+			int bit_nr =
+			    bitrev32(~crc32_le(~0, mclist->dmi_addr, 6)) >> 26;
+			/* The most significant bit determines the register to
+			 * use (H/L) while the other 5 bits determine the bit
+			 * within the register. */
+			mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
+		}
+		writel(mc_filter[0], ioaddr + GMAC_HASH_LOW);
+		writel(mc_filter[1], ioaddr + GMAC_HASH_HIGH);
+	}
+
+	/* Handle multiple unicast addresses (perfect filtering)*/
+	if (dev->uc_count > GMAC_MAX_UNICAST_ADDRESSES)
+		/* Switch to promiscuous mode is more than 16 addrs
+		   are required */
+		value |= GMAC_FRAME_FILTER_PR;
+	else {
+		int i;
+		struct dev_addr_list *uc_ptr = dev->uc_list;
+
+			for (i = 0; i < dev->uc_count; i++) {
+				gmac_set_umac_addr(ioaddr, uc_ptr->da_addr,
+						i + 1);
+
+				DBG(KERN_INFO "\t%d "
+				"- Unicast addr %02x:%02x:%02x:%02x:%02x:"
+				"%02x\n", i + 1,
+				uc_ptr->da_addr[0], uc_ptr->da_addr[1],
+				uc_ptr->da_addr[2], uc_ptr->da_addr[3],
+				uc_ptr->da_addr[4], uc_ptr->da_addr[5]);
+				uc_ptr = uc_ptr->next;
+		}
+	}
+
+#ifdef FRAME_FILTER_DEBUG
+	/* Enable Receive all mode (to debug filtering_fail errors) */
+	value |= GMAC_FRAME_FILTER_RA;
+#endif
+	writel(value, ioaddr + GMAC_FRAME_FILTER);
+
+	DBG(KERN_INFO "\tFrame Filter reg: 0x%08x\n\tHash regs: "
+	    "HI 0x%08x, LO 0x%08x\n", readl(ioaddr + GMAC_FRAME_FILTER),
+	    readl(ioaddr + GMAC_HASH_HIGH), readl(ioaddr + GMAC_HASH_LOW));
+
+	return;
+}
+
+static void gmac_flow_ctrl(unsigned long ioaddr, unsigned int duplex,
+			   unsigned int fc, unsigned int pause_time)
+{
+	unsigned int flow = 0;
+
+	DBG(KERN_DEBUG "GMAC Flow-Control:\n");
+	if (fc & FLOW_RX) {
+		DBG(KERN_DEBUG "\tReceive Flow-Control ON\n");
+		flow |= GMAC_FLOW_CTRL_RFE;
+	}
+	if (fc & FLOW_TX) {
+		DBG(KERN_DEBUG "\tTransmit Flow-Control ON\n");
+		flow |= GMAC_FLOW_CTRL_TFE;
+	}
+
+	if (duplex) {
+		DBG(KERN_DEBUG "\tduplex mode: pause time: %d\n", pause_time);
+		flow |= (pause_time << GMAC_FLOW_CTRL_PT_SHIFT);
+	}
+
+	writel(flow, ioaddr + GMAC_FLOW_CTRL);
+	return;
+}
+
+static void gmac_pmt(unsigned long ioaddr, unsigned long mode)
+{
+	unsigned int pmt = 0;
+
+	if (mode == WAKE_MAGIC) {
+		DBG(KERN_DEBUG "GMAC: WOL Magic frame\n");
+		pmt |= power_down | magic_pkt_en;
+	} else if (mode == WAKE_UCAST) {
+		DBG(KERN_DEBUG "GMAC: WOL on global unicast\n");
+		pmt |= global_unicast;
+	}
+
+	writel(pmt, ioaddr + GMAC_PMT);
+	return;
+}
+
+static void gmac_init_rx_desc(struct dma_desc *p, unsigned int ring_size,
+				int disable_rx_ic)
+{
+	int i;
+	for (i = 0; i < ring_size; i++) {
+		p->des01.erx.own = 1;
+		p->des01.erx.buffer1_size = BUF_SIZE_8KiB - 1;
+		/* To support jumbo frames */
+		p->des01.erx.buffer2_size = BUF_SIZE_8KiB - 1;
+		if (i == ring_size - 1)
+			p->des01.erx.end_ring = 1;
+		if (disable_rx_ic)
+			p->des01.erx.disable_ic = 1;
+		p++;
+	}
+	return;
+}
+
+static void gmac_init_tx_desc(struct dma_desc *p, unsigned int ring_size)
+{
+	int i;
+
+	for (i = 0; i < ring_size; i++) {
+		p->des01.etx.own = 0;
+		if (i == ring_size - 1)
+			p->des01.etx.end_ring = 1;
+		p++;
+	}
+
+	return;
+}
+
+static int gmac_get_tx_owner(struct dma_desc *p)
+{
+	return p->des01.etx.own;
+}
+
+static int gmac_get_rx_owner(struct dma_desc *p)
+{
+	return p->des01.erx.own;
+}
+
+static void gmac_set_tx_owner(struct dma_desc *p)
+{
+	p->des01.etx.own = 1;
+}
+
+static void gmac_set_rx_owner(struct dma_desc *p)
+{
+	p->des01.erx.own = 1;
+}
+
+static int gmac_get_tx_ls(struct dma_desc *p)
+{
+	return p->des01.etx.last_segment;
+}
+
+static void gmac_release_tx_desc(struct dma_desc *p)
+{
+	int ter = p->des01.etx.end_ring;
+
+	memset(p, 0, sizeof(struct dma_desc));
+	p->des01.etx.end_ring = ter;
+
+	return;
+}
+
+static void gmac_prepare_tx_desc(struct dma_desc *p, int is_fs, int len,
+				 int csum_flag)
+{
+	p->des01.etx.first_segment = is_fs;
+	if (unlikely(len > BUF_SIZE_4KiB)) {
+		p->des01.etx.buffer1_size = BUF_SIZE_4KiB;
+		p->des01.etx.buffer2_size = len - BUF_SIZE_4KiB;
+	} else {
+		p->des01.etx.buffer1_size = len;
+	}
+	if (likely(csum_flag))
+		p->des01.etx.checksum_insertion = cic_full;
+}
+
+static void gmac_clear_tx_ic(struct dma_desc *p)
+{
+	p->des01.etx.interrupt = 0;
+}
+
+static void gmac_close_tx_desc(struct dma_desc *p)
+{
+	p->des01.etx.last_segment = 1;
+	p->des01.etx.interrupt = 1;
+}
+
+static int gmac_get_rx_frame_len(struct dma_desc *p)
+{
+	return p->des01.erx.frame_length;
+}
+
+struct stmmac_ops gmac_driver = {
+	.core_init = gmac_core_init,
+	.dump_mac_regs = gmac_dump_regs,
+	.dma_init = gmac_dma_init,
+	.dump_dma_regs = gmac_dump_dma_regs,
+	.dma_mode = gmac_dma_operation_mode,
+	.dma_diagnostic_fr = gmac_dma_diagnostic_fr,
+	.tx_status = gmac_get_tx_frame_status,
+	.rx_status = gmac_get_rx_frame_status,
+	.get_tx_len = gmac_get_tx_len,
+	.set_filter = gmac_set_filter,
+	.flow_ctrl = gmac_flow_ctrl,
+	.pmt = gmac_pmt,
+	.init_rx_desc = gmac_init_rx_desc,
+	.init_tx_desc = gmac_init_tx_desc,
+	.get_tx_owner = gmac_get_tx_owner,
+	.get_rx_owner = gmac_get_rx_owner,
+	.release_tx_desc = gmac_release_tx_desc,
+	.prepare_tx_desc = gmac_prepare_tx_desc,
+	.clear_tx_ic = gmac_clear_tx_ic,
+	.close_tx_desc = gmac_close_tx_desc,
+	.get_tx_ls = gmac_get_tx_ls,
+	.set_tx_owner = gmac_set_tx_owner,
+	.set_rx_owner = gmac_set_rx_owner,
+	.get_rx_frame_len = gmac_get_rx_frame_len,
+	.host_irq_status = gmac_irq_status,
+	.set_umac_addr = gmac_set_umac_addr,
+	.get_umac_addr = gmac_get_umac_addr,
+};
+
+struct mac_device_info *gmac_setup(unsigned long ioaddr)
+{
+	struct mac_device_info *mac;
+	u32 uid = readl(ioaddr + GMAC_VERSION);
+
+	pr_info("\tGMAC - user ID: 0x%x, Synopsys ID: 0x%x\n",
+	       ((uid & 0x0000ff00) >> 8), (uid & 0x000000ff));
+
+	mac = kzalloc(sizeof(const struct mac_device_info), GFP_KERNEL);
+
+	mac->ops = &gmac_driver;
+	mac->hw.pmt = PMT_SUPPORTED;
+	mac->hw.link.port = GMAC_CONTROL_PS;
+	mac->hw.link.duplex = GMAC_CONTROL_DM;
+	mac->hw.link.speed = GMAC_CONTROL_FES;
+	mac->hw.mii.addr = GMAC_MII_ADDR;
+	mac->hw.mii.data = GMAC_MII_DATA;
+
+	return mac;
+}
diff --git a/drivers/net/stmmac/gmac.h b/drivers/net/stmmac/gmac.h
new file mode 100644
index 0000000..684a363
--- /dev/null
+++ b/drivers/net/stmmac/gmac.h
@@ -0,0 +1,204 @@
+/*******************************************************************************
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#define GMAC_CONTROL		0x00000000	/* Configuration */
+#define GMAC_FRAME_FILTER	0x00000004	/* Frame Filter */
+#define GMAC_HASH_HIGH		0x00000008	/* Multicast Hash Table High */
+#define GMAC_HASH_LOW		0x0000000c	/* Multicast Hash Table Low */
+#define GMAC_MII_ADDR		0x00000010	/* MII Address */
+#define GMAC_MII_DATA		0x00000014	/* MII Data */
+#define GMAC_FLOW_CTRL		0x00000018	/* Flow Control */
+#define GMAC_VLAN_TAG		0x0000001c	/* VLAN Tag */
+#define GMAC_VERSION		0x00000020	/* GMAC CORE Version */
+#define GMAC_WAKEUP_FILTER	0x00000028	/* Wake-up Frame Filter */
+
+#define GMAC_INT_STATUS		0x00000038	/* interrupt status register */
+enum gmac_irq_status {
+	time_stamp_irq = 0x0200,
+	mmc_rx_csum_offload_irq = 0x0080,
+	mmc_tx_irq = 0x0040,
+	mmc_rx_irq = 0x0020,
+	mmc_irq = 0x0010,
+	pmt_irq = 0x0008,
+	pcs_ane_irq = 0x0004,
+	pcs_link_irq = 0x0002,
+	rgmii_irq = 0x0001,
+};
+#define GMAC_INT_MASK		0x0000003c	/* interrupt mask register */
+
+/* PMT Control and Status */
+#define GMAC_PMT		0x0000002c
+enum power_event {
+	pointer_reset = 0x80000000,
+	global_unicast = 0x00000200,
+	wake_up_rx_frame = 0x00000040,
+	magic_frame = 0x00000020,
+	wake_up_frame_en = 0x00000004,
+	magic_pkt_en = 0x00000002,
+	power_down = 0x00000001,
+};
+
+/* GMAC HW ADDR regs */
+#define GMAC_ADDR_HIGH(reg)		(0x00000040+(reg * 8))
+#define GMAC_ADDR_LOW(reg)		(0x00000044+(reg * 8))
+#define GMAC_MAX_UNICAST_ADDRESSES	16
+
+#define GMAC_AN_CTRL	0x000000c0	/* AN control */
+#define GMAC_AN_STATUS	0x000000c4	/* AN status */
+#define GMAC_ANE_ADV	0x000000c8	/* Auto-Neg. Advertisement */
+#define GMAC_ANE_LINK	0x000000cc	/* Auto-Neg. link partener ability */
+#define GMAC_ANE_EXP	0x000000d0	/* ANE expansion */
+#define GMAC_TBI	0x000000d4	/* TBI extend status */
+#define GMAC_GMII_STATUS 0x000000d8	/* S/R-GMII status */
+
+/* GMAC Configuration defines */
+#define GMAC_CONTROL_TC	0x01000000	/* Transmit Conf. in RGMII/SGMII */
+#define GMAC_CONTROL_WD	0x00800000	/* Disable Watchdog on receive */
+#define GMAC_CONTROL_JD	0x00400000	/* Jabber disable */
+#define GMAC_CONTROL_BE	0x00200000	/* Frame Burst Enable */
+#define GMAC_CONTROL_JE	0x00100000	/* Jumbo frame */
+enum inter_frame_gap {
+	GMAC_CONTROL_IFG_88 = 0x00040000,
+	GMAC_CONTROL_IFG_80 = 0x00020000,
+	GMAC_CONTROL_IFG_40 = 0x000e0000,
+};
+#define GMAC_CONTROL_DCRS	0x00010000 /* Disable carrier sense during tx */
+#define GMAC_CONTROL_PS		0x00008000 /* Port Select 0:GMI 1:MII */
+#define GMAC_CONTROL_FES	0x00004000 /* Speed 0:10 1:100 */
+#define GMAC_CONTROL_DO		0x00002000 /* Disable Rx Own */
+#define GMAC_CONTROL_LM		0x00001000 /* Loop-back mode */
+#define GMAC_CONTROL_DM		0x00000800 /* Duplex Mode */
+#define GMAC_CONTROL_IPC	0x00000400 /* Checksum Offload */
+#define GMAC_CONTROL_DR		0x00000200 /* Disable Retry */
+#define GMAC_CONTROL_LUD	0x00000100 /* Link up/down */
+#define GMAC_CONTROL_ACS	0x00000080 /* Automatic Pad Stripping */
+#define GMAC_CONTROL_DC		0x00000010 /* Deferral Check */
+#define GMAC_CONTROL_TE		0x00000008 /* Transmitter Enable */
+#define GMAC_CONTROL_RE		0x00000004 /* Receiver Enable */
+
+#define GMAC_CORE_INIT (GMAC_CONTROL_JD | GMAC_CONTROL_PS | GMAC_CONTROL_ACS | \
+			GMAC_CONTROL_IPC | GMAC_CONTROL_JE | GMAC_CONTROL_BE)
+
+/* GMAC Frame Filter defines */
+#define GMAC_FRAME_FILTER_PR	0x00000001	/* Promiscuous Mode */
+#define GMAC_FRAME_FILTER_HUC	0x00000002	/* Hash Unicast */
+#define GMAC_FRAME_FILTER_HMC	0x00000004	/* Hash Multicast */
+#define GMAC_FRAME_FILTER_DAIF	0x00000008	/* DA Inverse Filtering */
+#define GMAC_FRAME_FILTER_PM	0x00000010	/* Pass all multicast */
+#define GMAC_FRAME_FILTER_DBF	0x00000020	/* Disable Broadcast frames */
+#define GMAC_FRAME_FILTER_SAIF	0x00000100	/* Inverse Filtering */
+#define GMAC_FRAME_FILTER_SAF	0x00000200	/* Source Address Filter */
+#define GMAC_FRAME_FILTER_HPF	0x00000400	/* Hash or perfect Filter */
+#define GMAC_FRAME_FILTER_RA	0x80000000	/* Receive all mode */
+/* GMII ADDR  defines */
+#define GMAC_MII_ADDR_WRITE	0x00000002	/* MII Write */
+#define GMAC_MII_ADDR_BUSY	0x00000001	/* MII Busy */
+/* GMAC FLOW CTRL defines */
+#define GMAC_FLOW_CTRL_PT_MASK	0xffff0000	/* Pause Time Mask */
+#define GMAC_FLOW_CTRL_PT_SHIFT	16
+#define GMAC_FLOW_CTRL_RFE	0x00000004	/* Rx Flow Control Enable */
+#define GMAC_FLOW_CTRL_TFE	0x00000002	/* Tx Flow Control Enable */
+#define GMAC_FLOW_CTRL_FCB_BPA	0x00000001	/* Flow Control Busy ... */
+
+/*--- DMA BLOCK defines ---*/
+/* DMA Bus Mode register defines */
+#define DMA_BUS_MODE_SFT_RESET	0x00000001	/* Software Reset */
+#define DMA_BUS_MODE_DA		0x00000002	/* Arbitration scheme */
+#define DMA_BUS_MODE_DSL_MASK	0x0000007c	/* Descriptor Skip Length */
+#define DMA_BUS_MODE_DSL_SHIFT	2	/*   (in DWORDS)      */
+/* Programmable burst length (passed thorugh platform)*/
+#define DMA_BUS_MODE_PBL_MASK	0x00003f00	/* Programmable Burst Len */
+#define DMA_BUS_MODE_PBL_SHIFT	8
+
+enum rx_tx_priority_ratio {
+	double_ratio = 0x00004000,	/*2:1 */
+	triple_ratio = 0x00008000,	/*3:1 */
+	quadruple_ratio = 0x0000c000,	/*4:1 */
+};
+
+#define DMA_BUS_MODE_FB		0x00010000	/* Fixed burst */
+#define DMA_BUS_MODE_RPBL_MASK	0x003e0000	/* Rx-Programmable Burst Len */
+#define DMA_BUS_MODE_RPBL_SHIFT	17
+#define DMA_BUS_MODE_USP	0x00800000
+#define DMA_BUS_MODE_4PBL	0x01000000
+#define DMA_BUS_MODE_AAL	0x02000000
+
+/* DMA CRS Control and Status Register Mapping */
+#define DMA_HOST_TX_DESC	  0x00001048	/* Current Host Tx descriptor */
+#define DMA_HOST_RX_DESC	  0x0000104c	/* Current Host Rx descriptor */
+/*  DMA Bus Mode register defines */
+#define DMA_BUS_PR_RATIO_MASK	  0x0000c000	/* Rx/Tx priority ratio */
+#define DMA_BUS_PR_RATIO_SHIFT	  14
+#define DMA_BUS_FB	  	  0x00010000	/* Fixed Burst */
+
+/* DMA operation mode defines (start/stop tx/rx are placed in common header)*/
+#define DMA_CONTROL_DT		0x04000000 /* Disable Drop TCP/IP csum error */
+#define DMA_CONTROL_RSF		0x02000000 /* Receive Store and Forward */
+#define DMA_CONTROL_DFF		0x01000000 /* Disaable flushing */
+/* Theshold for Activating the FC */
+enum rfa {
+	act_full_minus_1 = 0x00800000,
+	act_full_minus_2 = 0x00800200,
+	act_full_minus_3 = 0x00800400,
+	act_full_minus_4 = 0x00800600,
+};
+/* Theshold for Deactivating the FC */
+enum rfd {
+	deac_full_minus_1 = 0x00400000,
+	deac_full_minus_2 = 0x00400800,
+	deac_full_minus_3 = 0x00401000,
+	deac_full_minus_4 = 0x00401800,
+};
+#define DMA_CONTROL_TSF		0x00200000 /* Transmit  Store and Forward */
+#define DMA_CONTROL_FTF		0x00100000 /* Flush transmit FIFO */
+
+enum ttc_control {
+	DMA_CONTROL_TTC_64 = 0x00000000,
+	DMA_CONTROL_TTC_128 = 0x00004000,
+	DMA_CONTROL_TTC_192 = 0x00008000,
+	DMA_CONTROL_TTC_256 = 0x0000c000,
+	DMA_CONTROL_TTC_40 = 0x00010000,
+	DMA_CONTROL_TTC_32 = 0x00014000,
+	DMA_CONTROL_TTC_24 = 0x00018000,
+	DMA_CONTROL_TTC_16 = 0x0001c000,
+};
+#define DMA_CONTROL_TC_TX_MASK	0xfffe3fff
+
+#define DMA_CONTROL_EFC		0x00000100
+#define DMA_CONTROL_FEF		0x00000080
+#define DMA_CONTROL_FUF		0x00000040
+
+enum rtc_control {
+	DMA_CONTROL_RTC_64 = 0x00000000,
+	DMA_CONTROL_RTC_32 = 0x00000008,
+	DMA_CONTROL_RTC_96 = 0x00000010,
+	DMA_CONTROL_RTC_128 = 0x00000018,
+};
+#define DMA_CONTROL_TC_RX_MASK	0xffffffe7
+
+#define DMA_CONTROL_OSF	0x00000004	/* Operate on second frame */
+
+/* MMC registers offset */
+#define GMAC_MMC_CTRL      0x100
+#define GMAC_MMC_RX_INTR   0x104
+#define GMAC_MMC_TX_INTR   0x108
+#define GMAC_MMC_RX_CSUM_OFFLOAD   0x208
diff --git a/drivers/net/stmmac/mac100.c b/drivers/net/stmmac/mac100.c
new file mode 100644
index 0000000..625171b
--- /dev/null
+++ b/drivers/net/stmmac/mac100.c
@@ -0,0 +1,517 @@
+/*******************************************************************************
+  This is the driver for the MAC 10/100 on-chip Ethernet controller
+  currently tested on all the ST boards based on STb7109 and stx7200 SoCs.
+
+  DWC Ether MAC 10/100 Universal version 4.0 has been used for developing
+  this code.
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#include <linux/netdevice.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include "common.h"
+#include "mac100.h"
+
+#undef MAC100_DEBUG
+/*#define MAC100_DEBUG*/
+#ifdef MAC100_DEBUG
+#define DBG(fmt, args...)  printk(fmt, ## args)
+#else
+#define DBG(fmt, args...)  do { } while (0)
+#endif
+
+static void mac100_core_init(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + MAC_CONTROL);
+
+	writel((value | MAC_CORE_INIT), ioaddr + MAC_CONTROL);
+
+#ifdef STMMAC_VLAN_TAG_USED
+	writel(ETH_P_8021Q, ioaddr + MAC_VLAN1);
+#endif
+	return;
+}
+
+static void mac100_dump_mac_regs(unsigned long ioaddr)
+{
+	pr_info("\t----------------------------------------------\n"
+	       "\t  MAC100 CSR (base addr = 0x%8x)\n"
+	       "\t----------------------------------------------\n",
+	       (unsigned int)ioaddr);
+	pr_info("\tcontrol reg (offset 0x%x): 0x%08x\n", MAC_CONTROL,
+	       readl(ioaddr + MAC_CONTROL));
+	pr_info("\taddr HI (offset 0x%x): 0x%08x\n ", MAC_ADDR_HIGH,
+	       readl(ioaddr + MAC_ADDR_HIGH));
+	pr_info("\taddr LO (offset 0x%x): 0x%08x\n", MAC_ADDR_LOW,
+	       readl(ioaddr + MAC_ADDR_LOW));
+	pr_info("\tmulticast hash HI (offset 0x%x): 0x%08x\n",
+			MAC_HASH_HIGH, readl(ioaddr + MAC_HASH_HIGH));
+	pr_info("\tmulticast hash LO (offset 0x%x): 0x%08x\n",
+			MAC_HASH_LOW, readl(ioaddr + MAC_HASH_LOW));
+	pr_info("\tflow control (offset 0x%x): 0x%08x\n",
+		MAC_FLOW_CTRL, readl(ioaddr + MAC_FLOW_CTRL));
+	pr_info("\tVLAN1 tag (offset 0x%x): 0x%08x\n", MAC_VLAN1,
+	       readl(ioaddr + MAC_VLAN1));
+	pr_info("\tVLAN2 tag (offset 0x%x): 0x%08x\n", MAC_VLAN2,
+	       readl(ioaddr + MAC_VLAN2));
+	pr_info("\n\tMAC management counter registers\n");
+	pr_info("\t MMC crtl (offset 0x%x): 0x%08x\n",
+	       MMC_CONTROL, readl(ioaddr + MMC_CONTROL));
+	pr_info("\t MMC High Interrupt (offset 0x%x): 0x%08x\n",
+	       MMC_HIGH_INTR, readl(ioaddr + MMC_HIGH_INTR));
+	pr_info("\t MMC Low Interrupt (offset 0x%x): 0x%08x\n",
+	       MMC_LOW_INTR, readl(ioaddr + MMC_LOW_INTR));
+	pr_info("\t MMC High Interrupt Mask (offset 0x%x): 0x%08x\n",
+	       MMC_HIGH_INTR_MASK, readl(ioaddr + MMC_HIGH_INTR_MASK));
+	pr_info("\t MMC Low Interrupt Mask (offset 0x%x): 0x%08x\n",
+	       MMC_LOW_INTR_MASK, readl(ioaddr + MMC_LOW_INTR_MASK));
+	return;
+}
+
+static int mac100_dma_init(unsigned long ioaddr, int pbl, u32 dma_tx,
+			   u32 dma_rx)
+{
+	u32 value = readl(ioaddr + DMA_BUS_MODE);
+	/* DMA SW reset */
+	value |= DMA_BUS_MODE_SFT_RESET;
+	writel(value, ioaddr + DMA_BUS_MODE);
+	do {} while ((readl(ioaddr + DMA_BUS_MODE) & DMA_BUS_MODE_SFT_RESET));
+
+	/* Enable Application Access by writing to DMA CSR0 */
+	writel(DMA_BUS_MODE_DEFAULT | (pbl << DMA_BUS_MODE_PBL_SHIFT),
+	       ioaddr + DMA_BUS_MODE);
+
+	/* Mask interrupts by writing to CSR7 */
+	writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA);
+
+	/* The base address of the RX/TX descriptor lists must be written into
+	 * DMA CSR3 and CSR4, respectively. */
+	writel(dma_tx, ioaddr + DMA_TX_BASE_ADDR);
+	writel(dma_rx, ioaddr + DMA_RCV_BASE_ADDR);
+
+	return 0;
+}
+
+/* Store and Forward capability is not used at all..
+ * The transmit threshold can be programmed by
+ * setting the TTC bits in the DMA control register.*/
+static void mac100_dma_operation_mode(unsigned long ioaddr, int txmode,
+				      int rxmode)
+{
+	u32 csr6 = readl(ioaddr + DMA_CONTROL);
+
+	if (txmode <= 32)
+		csr6 |= DMA_CONTROL_TTC_32;
+	else if (txmode <= 64)
+		csr6 |= DMA_CONTROL_TTC_64;
+	else
+		csr6 |= DMA_CONTROL_TTC_128;
+
+	writel(csr6, ioaddr + DMA_CONTROL);
+
+	return;
+}
+
+static void mac100_dump_dma_regs(unsigned long ioaddr)
+{
+	int i;
+
+	DBG(KERN_DEBUG "MAC100 DMA CSR \n");
+	for (i = 0; i < 9; i++)
+		pr_debug("\t CSR%d (offset 0x%x): 0x%08x\n", i,
+		       (DMA_BUS_MODE + i * 4),
+		       readl(ioaddr + DMA_BUS_MODE + i * 4));
+	DBG(KERN_DEBUG "\t CSR20 (offset 0x%x): 0x%08x\n",
+	    DMA_CUR_TX_BUF_ADDR, readl(ioaddr + DMA_CUR_TX_BUF_ADDR));
+	DBG(KERN_DEBUG "\t CSR21 (offset 0x%x): 0x%08x\n",
+	    DMA_CUR_RX_BUF_ADDR, readl(ioaddr + DMA_CUR_RX_BUF_ADDR));
+	return;
+}
+
+/* DMA controller has two counters to track the number of
+   the receive missed frames. */
+static void mac100_dma_diagnostic_fr(void *data, struct stmmac_extra_stats *x,
+				     unsigned long ioaddr)
+{
+	struct net_device_stats *stats = (struct net_device_stats *)data;
+	u32 csr8 = readl(ioaddr + DMA_MISSED_FRAME_CTR);
+
+	if (unlikely(csr8)) {
+		if (csr8 & DMA_MISSED_FRAME_OVE) {
+			stats->rx_over_errors += 0x800;
+			x->rx_overflow_cntr += 0x800;
+		} else {
+			unsigned int ove_cntr;
+			ove_cntr = ((csr8 & DMA_MISSED_FRAME_OVE_CNTR) >> 17);
+			stats->rx_over_errors += ove_cntr;
+			x->rx_overflow_cntr += ove_cntr;
+		}
+
+		if (csr8 & DMA_MISSED_FRAME_OVE_M) {
+			stats->rx_missed_errors += 0xffff;
+			x->rx_missed_cntr += 0xffff;
+		} else {
+			unsigned int miss_f = (csr8 & DMA_MISSED_FRAME_M_CNTR);
+			stats->rx_missed_errors += miss_f;
+			x->rx_missed_cntr += miss_f;
+		}
+	}
+	return;
+}
+
+static int mac100_get_tx_frame_status(void *data, struct stmmac_extra_stats *x,
+				      struct dma_desc *p, unsigned long ioaddr)
+{
+	int ret = 0;
+	struct net_device_stats *stats = (struct net_device_stats *)data;
+
+	if (unlikely(p->des01.tx.error_summary)) {
+		if (unlikely(p->des01.tx.underflow_error)) {
+			x->tx_underflow++;
+			stats->tx_fifo_errors++;
+		}
+		if (unlikely(p->des01.tx.no_carrier)) {
+			x->tx_carrier++;
+			stats->tx_carrier_errors++;
+		}
+		if (unlikely(p->des01.tx.loss_carrier)) {
+			x->tx_losscarrier++;
+			stats->tx_carrier_errors++;
+		}
+		if (unlikely((p->des01.tx.excessive_deferral) ||
+			     (p->des01.tx.excessive_collisions) ||
+			     (p->des01.tx.late_collision)))
+			stats->collisions += p->des01.tx.collision_count;
+		ret = -1;
+	}
+	if (unlikely(p->des01.tx.heartbeat_fail)) {
+		x->tx_heartbeat++;
+		stats->tx_heartbeat_errors++;
+		ret = -1;
+	}
+	if (unlikely(p->des01.tx.deferred))
+		x->tx_deferred++;
+
+	return ret;
+}
+
+static int mac100_get_tx_len(struct dma_desc *p)
+{
+	return p->des01.tx.buffer1_size;
+}
+
+/* This function verifies if each incoming frame has some errors
+ * and, if required, updates the multicast statistics.
+ * In case of success, it returns csum_none becasue the device
+ * is not able to compute the csum in HW. */
+static int mac100_get_rx_frame_status(void *data, struct stmmac_extra_stats *x,
+				      struct dma_desc *p)
+{
+	int ret = csum_none;
+	struct net_device_stats *stats = (struct net_device_stats *)data;
+
+	if (unlikely(p->des01.rx.last_descriptor == 0)) {
+		pr_warning("mac100 Error: Oversized Ethernet "
+			   "frame spanned multiple buffers\n");
+		stats->rx_length_errors++;
+		return discard_frame;
+	}
+
+	if (unlikely(p->des01.rx.error_summary)) {
+		if (unlikely(p->des01.rx.descriptor_error))
+			x->rx_desc++;
+		if (unlikely(p->des01.rx.partial_frame_error))
+			x->rx_partial++;
+		if (unlikely(p->des01.rx.run_frame))
+			x->rx_runt++;
+		if (unlikely(p->des01.rx.frame_too_long))
+			x->rx_toolong++;
+		if (unlikely(p->des01.rx.collision)) {
+			x->rx_collision++;
+			stats->collisions++;
+		}
+		if (unlikely(p->des01.rx.crc_error)) {
+			x->rx_crc++;
+			stats->rx_crc_errors++;
+		}
+		ret = discard_frame;
+	}
+	if (unlikely(p->des01.rx.dribbling))
+		ret = discard_frame;
+
+	if (unlikely(p->des01.rx.length_error)) {
+		x->rx_lenght++;
+		ret = discard_frame;
+	}
+	if (unlikely(p->des01.rx.mii_error)) {
+		x->rx_mii++;
+		ret = discard_frame;
+	}
+	if (p->des01.rx.multicast_frame) {
+		x->rx_multicast++;
+		stats->multicast++;
+	}
+	return ret;
+}
+
+static void mac100_irq_status(unsigned long ioaddr)
+{
+	return;
+}
+
+static void mac100_set_umac_addr(unsigned long ioaddr, unsigned char *addr,
+			  unsigned int reg_n)
+{
+	stmmac_set_mac_addr(ioaddr, addr, MAC_ADDR_HIGH, MAC_ADDR_LOW);
+}
+
+static void mac100_get_umac_addr(unsigned long ioaddr, unsigned char *addr,
+			  unsigned int reg_n)
+{
+	stmmac_get_mac_addr(ioaddr, addr, MAC_ADDR_HIGH, MAC_ADDR_LOW);
+}
+
+static void mac100_set_filter(struct net_device *dev)
+{
+	unsigned long ioaddr = dev->base_addr;
+	u32 value = readl(ioaddr + MAC_CONTROL);
+
+	if (dev->flags & IFF_PROMISC) {
+		value |= MAC_CONTROL_PR;
+		value &= ~(MAC_CONTROL_PM | MAC_CONTROL_IF | MAC_CONTROL_HO |
+			   MAC_CONTROL_HP);
+	} else if ((dev->mc_count > HASH_TABLE_SIZE)
+		   || (dev->flags & IFF_ALLMULTI)) {
+		value |= MAC_CONTROL_PM;
+		value &= ~(MAC_CONTROL_PR | MAC_CONTROL_IF | MAC_CONTROL_HO);
+		writel(0xffffffff, ioaddr + MAC_HASH_HIGH);
+		writel(0xffffffff, ioaddr + MAC_HASH_LOW);
+	} else if (dev->mc_count == 0) {	/* no multicast */
+		value &= ~(MAC_CONTROL_PM | MAC_CONTROL_PR | MAC_CONTROL_IF |
+			   MAC_CONTROL_HO | MAC_CONTROL_HP);
+	} else {
+		int i;
+		u32 mc_filter[2];
+		struct dev_mc_list *mclist;
+
+		/* Perfect filter mode for physical address and Hash
+		   filter for multicast */
+		value |= MAC_CONTROL_HP;
+		value &= ~(MAC_CONTROL_PM | MAC_CONTROL_PR | MAC_CONTROL_IF
+			   | MAC_CONTROL_HO);
+
+		memset(mc_filter, 0, sizeof(mc_filter));
+		for (i = 0, mclist = dev->mc_list;
+		     mclist && i < dev->mc_count; i++, mclist = mclist->next) {
+			/* The upper 6 bits of the calculated CRC are used to
+			 * index the contens of the hash table */
+			int bit_nr =
+			    ether_crc(ETH_ALEN, mclist->dmi_addr) >> 26;
+			/* The most significant bit determines the register to
+			 * use (H/L) while the other 5 bits determine the bit
+			 * within the register. */
+			mc_filter[bit_nr >> 5] |= 1 << (bit_nr & 31);
+		}
+		writel(mc_filter[0], ioaddr + MAC_HASH_LOW);
+		writel(mc_filter[1], ioaddr + MAC_HASH_HIGH);
+	}
+
+	writel(value, ioaddr + MAC_CONTROL);
+
+	DBG(KERN_INFO "%s: CTRL reg: 0x%08x Hash regs: "
+	    "HI 0x%08x, LO 0x%08x\n",
+	    __func__, readl(ioaddr + MAC_CONTROL),
+	    readl(ioaddr + MAC_HASH_HIGH), readl(ioaddr + MAC_HASH_LOW));
+	return;
+}
+
+static void mac100_flow_ctrl(unsigned long ioaddr, unsigned int duplex,
+			     unsigned int fc, unsigned int pause_time)
+{
+	unsigned int flow = MAC_FLOW_CTRL_ENABLE;
+
+	if (duplex)
+		flow |= (pause_time << MAC_FLOW_CTRL_PT_SHIFT);
+	writel(flow, ioaddr + MAC_FLOW_CTRL);
+
+	return;
+}
+
+/* No PMT module supported in our SoC  for the Ethernet Controller. */
+static void mac100_pmt(unsigned long ioaddr, unsigned long mode)
+{
+	return;
+}
+
+static void mac100_init_rx_desc(struct dma_desc *p, unsigned int ring_size,
+				int disable_rx_ic)
+{
+	int i;
+	for (i = 0; i < ring_size; i++) {
+		p->des01.rx.own = 1;
+		p->des01.rx.buffer1_size = BUF_SIZE_2KiB - 1;
+		if (i == ring_size - 1)
+			p->des01.rx.end_ring = 1;
+		if (disable_rx_ic)
+			p->des01.rx.disable_ic = 1;
+		p++;
+	}
+	return;
+}
+
+static void mac100_init_tx_desc(struct dma_desc *p, unsigned int ring_size)
+{
+	int i;
+	for (i = 0; i < ring_size; i++) {
+		p->des01.tx.own = 0;
+		if (i == ring_size - 1)
+			p->des01.tx.end_ring = 1;
+		p++;
+	}
+	return;
+}
+
+static int mac100_get_tx_owner(struct dma_desc *p)
+{
+	return p->des01.tx.own;
+}
+
+static int mac100_get_rx_owner(struct dma_desc *p)
+{
+	return p->des01.rx.own;
+}
+
+static void mac100_set_tx_owner(struct dma_desc *p)
+{
+	p->des01.tx.own = 1;
+}
+
+static void mac100_set_rx_owner(struct dma_desc *p)
+{
+	p->des01.rx.own = 1;
+}
+
+static int mac100_get_tx_ls(struct dma_desc *p)
+{
+	return p->des01.tx.last_segment;
+}
+
+static void mac100_release_tx_desc(struct dma_desc *p)
+{
+	int ter = p->des01.tx.end_ring;
+
+	/* clean field used within the xmit */
+	p->des01.tx.first_segment = 0;
+	p->des01.tx.last_segment = 0;
+	p->des01.tx.buffer1_size = 0;
+
+	/* clean status reported */
+	p->des01.tx.error_summary = 0;
+	p->des01.tx.underflow_error = 0;
+	p->des01.tx.no_carrier = 0;
+	p->des01.tx.loss_carrier = 0;
+	p->des01.tx.excessive_deferral = 0;
+	p->des01.tx.excessive_collisions = 0;
+	p->des01.tx.late_collision = 0;
+	p->des01.tx.heartbeat_fail = 0;
+	p->des01.tx.deferred = 0;
+
+	/* set termination field */
+	p->des01.tx.end_ring = ter;
+
+	return;
+}
+
+static void mac100_prepare_tx_desc(struct dma_desc *p, int is_fs, int len,
+				   int csum_flag)
+{
+	p->des01.tx.first_segment = is_fs;
+	p->des01.tx.buffer1_size = len;
+}
+
+static void mac100_clear_tx_ic(struct dma_desc *p)
+{
+	p->des01.tx.interrupt = 0;
+}
+
+static void mac100_close_tx_desc(struct dma_desc *p)
+{
+	p->des01.tx.last_segment = 1;
+	p->des01.tx.interrupt = 1;
+}
+
+static int mac100_get_rx_frame_len(struct dma_desc *p)
+{
+	return p->des01.rx.frame_length;
+}
+
+struct stmmac_ops mac100_driver = {
+	.core_init = mac100_core_init,
+	.dump_mac_regs = mac100_dump_mac_regs,
+	.dma_init = mac100_dma_init,
+	.dump_dma_regs = mac100_dump_dma_regs,
+	.dma_mode = mac100_dma_operation_mode,
+	.dma_diagnostic_fr = mac100_dma_diagnostic_fr,
+	.tx_status = mac100_get_tx_frame_status,
+	.rx_status = mac100_get_rx_frame_status,
+	.get_tx_len = mac100_get_tx_len,
+	.set_filter = mac100_set_filter,
+	.flow_ctrl = mac100_flow_ctrl,
+	.pmt = mac100_pmt,
+	.init_rx_desc = mac100_init_rx_desc,
+	.init_tx_desc = mac100_init_tx_desc,
+	.get_tx_owner = mac100_get_tx_owner,
+	.get_rx_owner = mac100_get_rx_owner,
+	.release_tx_desc = mac100_release_tx_desc,
+	.prepare_tx_desc = mac100_prepare_tx_desc,
+	.clear_tx_ic = mac100_clear_tx_ic,
+	.close_tx_desc = mac100_close_tx_desc,
+	.get_tx_ls = mac100_get_tx_ls,
+	.set_tx_owner = mac100_set_tx_owner,
+	.set_rx_owner = mac100_set_rx_owner,
+	.get_rx_frame_len = mac100_get_rx_frame_len,
+	.host_irq_status = mac100_irq_status,
+	.set_umac_addr = mac100_set_umac_addr,
+	.get_umac_addr = mac100_get_umac_addr,
+};
+
+struct mac_device_info *mac100_setup(unsigned long ioaddr)
+{
+	struct mac_device_info *mac;
+
+	mac = kzalloc(sizeof(const struct mac_device_info), GFP_KERNEL);
+
+	pr_info("\tMAC 10/100\n");
+
+	mac->ops = &mac100_driver;
+	mac->hw.pmt = PMT_NOT_SUPPORTED;
+	mac->hw.link.port = MAC_CONTROL_PS;
+	mac->hw.link.duplex = MAC_CONTROL_F;
+	mac->hw.link.speed = 0;
+	mac->hw.mii.addr = MAC_MII_ADDR;
+	mac->hw.mii.data = MAC_MII_DATA;
+
+	return mac;
+}
diff --git a/drivers/net/stmmac/mac100.h b/drivers/net/stmmac/mac100.h
new file mode 100644
index 0000000..0f8f110
--- /dev/null
+++ b/drivers/net/stmmac/mac100.h
@@ -0,0 +1,116 @@
+/*******************************************************************************
+  MAC 10/100 Header File
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+/*----------------------------------------------------------------------------
+ *	 			MAC BLOCK defines
+ *---------------------------------------------------------------------------*/
+/* MAC CSR offset */
+#define MAC_CONTROL	0x00000000	/* MAC Control */
+#define MAC_ADDR_HIGH	0x00000004	/* MAC Address High */
+#define MAC_ADDR_LOW	0x00000008	/* MAC Address Low */
+#define MAC_HASH_HIGH	0x0000000c	/* Multicast Hash Table High */
+#define MAC_HASH_LOW	0x00000010	/* Multicast Hash Table Low */
+#define MAC_MII_ADDR	0x00000014	/* MII Address */
+#define MAC_MII_DATA	0x00000018	/* MII Data */
+#define MAC_FLOW_CTRL	0x0000001c	/* Flow Control */
+#define MAC_VLAN1	0x00000020	/* VLAN1 Tag */
+#define MAC_VLAN2	0x00000024	/* VLAN2 Tag */
+
+/* MAC CTRL defines */
+#define MAC_CONTROL_RA	0x80000000	/* Receive All Mode */
+#define MAC_CONTROL_BLE	0x40000000	/* Endian Mode */
+#define MAC_CONTROL_HBD	0x10000000	/* Heartbeat Disable */
+#define MAC_CONTROL_PS	0x08000000	/* Port Select */
+#define MAC_CONTROL_DRO	0x00800000	/* Disable Receive Own */
+#define MAC_CONTROL_EXT_LOOPBACK 0x00400000	/* Reserved (ext loopback?) */
+#define MAC_CONTROL_OM	0x00200000	/* Loopback Operating Mode */
+#define MAC_CONTROL_F	0x00100000	/* Full Duplex Mode */
+#define MAC_CONTROL_PM	0x00080000	/* Pass All Multicast */
+#define MAC_CONTROL_PR	0x00040000	/* Promiscuous Mode */
+#define MAC_CONTROL_IF	0x00020000	/* Inverse Filtering */
+#define MAC_CONTROL_PB	0x00010000	/* Pass Bad Frames */
+#define MAC_CONTROL_HO	0x00008000	/* Hash Only Filtering Mode */
+#define MAC_CONTROL_HP	0x00002000	/* Hash/Perfect Filtering Mode */
+#define MAC_CONTROL_LCC	0x00001000	/* Late Collision Control */
+#define MAC_CONTROL_DBF	0x00000800	/* Disable Broadcast Frames */
+#define MAC_CONTROL_DRTY	0x00000400	/* Disable Retry */
+#define MAC_CONTROL_ASTP	0x00000100	/* Automatic Pad Stripping */
+#define MAC_CONTROL_BOLMT_10	0x00000000	/* Back Off Limit 10 */
+#define MAC_CONTROL_BOLMT_8	0x00000040	/* Back Off Limit 8 */
+#define MAC_CONTROL_BOLMT_4	0x00000080	/* Back Off Limit 4 */
+#define MAC_CONTROL_BOLMT_1	0x000000c0	/* Back Off Limit 1 */
+#define MAC_CONTROL_DC		0x00000020	/* Deferral Check */
+#define MAC_CONTROL_TE		0x00000008	/* Transmitter Enable */
+#define MAC_CONTROL_RE		0x00000004	/* Receiver Enable */
+
+#define MAC_CORE_INIT (MAC_CONTROL_HBD | MAC_CONTROL_ASTP)
+
+/* MAC FLOW CTRL defines */
+#define MAC_FLOW_CTRL_PT_MASK	0xffff0000	/* Pause Time Mask */
+#define MAC_FLOW_CTRL_PT_SHIFT	16
+#define MAC_FLOW_CTRL_PASS	0x00000004	/* Pass Control Frames */
+#define MAC_FLOW_CTRL_ENABLE	0x00000002	/* Flow Control Enable */
+#define MAC_FLOW_CTRL_PAUSE	0x00000001	/* Flow Control Busy ... */
+
+/* MII ADDR  defines */
+#define MAC_MII_ADDR_WRITE	0x00000002	/* MII Write */
+#define MAC_MII_ADDR_BUSY	0x00000001	/* MII Busy */
+
+/*----------------------------------------------------------------------------
+ * 				DMA BLOCK defines
+ *---------------------------------------------------------------------------*/
+
+/* DMA Bus Mode register defines */
+#define DMA_BUS_MODE_DBO	0x00100000	/* Descriptor Byte Ordering */
+#define DMA_BUS_MODE_BLE	0x00000080	/* Big Endian/Little Endian */
+#define DMA_BUS_MODE_PBL_MASK	0x00003f00	/* Programmable Burst Len */
+#define DMA_BUS_MODE_PBL_SHIFT	8
+#define DMA_BUS_MODE_DSL_MASK	0x0000007c	/* Descriptor Skip Length */
+#define DMA_BUS_MODE_DSL_SHIFT	2	/*   (in DWORDS)      */
+#define DMA_BUS_MODE_BAR_BUS	0x00000002	/* Bar-Bus Arbitration */
+#define DMA_BUS_MODE_SFT_RESET	0x00000001	/* Software Reset */
+#define DMA_BUS_MODE_DEFAULT	0x00000000
+
+/* DMA Control register defines */
+#define DMA_CONTROL_SF		0x00200000	/* Store And Forward */
+
+/* Transmit Threshold Control */
+enum ttc_control {
+	DMA_CONTROL_TTC_DEFAULT = 0x00000000,	/* Threshold is 32 DWORDS */
+	DMA_CONTROL_TTC_64 = 0x00004000,	/* Threshold is 64 DWORDS */
+	DMA_CONTROL_TTC_128 = 0x00008000,	/* Threshold is 128 DWORDS */
+	DMA_CONTROL_TTC_256 = 0x0000c000,	/* Threshold is 256 DWORDS */
+	DMA_CONTROL_TTC_18 = 0x00400000,	/* Threshold is 18 DWORDS */
+	DMA_CONTROL_TTC_24 = 0x00404000,	/* Threshold is 24 DWORDS */
+	DMA_CONTROL_TTC_32 = 0x00408000,	/* Threshold is 32 DWORDS */
+	DMA_CONTROL_TTC_40 = 0x0040c000,	/* Threshold is 40 DWORDS */
+	DMA_CONTROL_SE = 0x00000008,	/* Stop On Empty */
+	DMA_CONTROL_OSF = 0x00000004,	/* Operate On 2nd Frame */
+};
+
+/* STMAC110 DMA Missed Frame Counter register defines */
+#define DMA_MISSED_FRAME_OVE	0x10000000	/* FIFO Overflow Overflow */
+#define DMA_MISSED_FRAME_OVE_CNTR 0x0ffe0000	/* Overflow Frame Counter */
+#define DMA_MISSED_FRAME_OVE_M	0x00010000	/* Missed Frame Overflow */
+#define DMA_MISSED_FRAME_M_CNTR	0x0000ffff	/* Missed Frame Couinter */
diff --git a/drivers/net/stmmac/stmmac.h b/drivers/net/stmmac/stmmac.h
new file mode 100644
index 0000000..6d2eae3
--- /dev/null
+++ b/drivers/net/stmmac/stmmac.h
@@ -0,0 +1,98 @@
+/*******************************************************************************
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#define DRV_MODULE_VERSION	"Oct_09"
+
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#define STMMAC_VLAN_TAG_USED
+#include <linux/if_vlan.h>
+#endif
+
+#include "common.h"
+#ifdef CONFIG_STMMAC_TIMER
+#include "stmmac_timer.h"
+#endif
+
+struct stmmac_priv {
+	/* Frequently used values are kept adjacent for cache effect */
+	struct dma_desc *dma_tx ____cacheline_aligned;
+	dma_addr_t dma_tx_phy;
+	struct sk_buff **tx_skbuff;
+	unsigned int cur_tx;
+	unsigned int dirty_tx;
+	unsigned int dma_tx_size;
+	int tx_coe;
+	int tx_coalesce;
+
+	struct dma_desc *dma_rx ;
+	unsigned int cur_rx;
+	unsigned int dirty_rx;
+	struct sk_buff **rx_skbuff;
+	dma_addr_t *rx_skbuff_dma;
+	struct sk_buff_head rx_recycle;
+
+	struct net_device *dev;
+	int is_gmac;
+	dma_addr_t dma_rx_phy;
+	unsigned int dma_rx_size;
+	int rx_csum;
+	unsigned int dma_buf_sz;
+	struct device *device;
+	struct mac_device_info *mac_type;
+
+	struct stmmac_extra_stats xstats;
+	struct napi_struct napi;
+
+	phy_interface_t phy_interface;
+	int pbl;
+	int bus_id;
+	int phy_addr;
+	int phy_mask;
+	int (*phy_reset) (void *priv);
+	void (*fix_mac_speed) (void *priv, unsigned int speed);
+	void *bsp_priv;
+
+	int phy_irq;
+	struct phy_device *phydev;
+	int oldlink;
+	int speed;
+	int oldduplex;
+	unsigned int flow_ctrl;
+	unsigned int pause;
+	struct mii_bus *mii;
+
+	u32 msg_enable;
+	spinlock_t lock;
+	int wolopts;
+	int wolenabled;
+	int shutdown;
+#ifdef CONFIG_STMMAC_TIMER
+	struct stmmac_timer *tm;
+#endif
+#ifdef STMMAC_VLAN_TAG_USED
+	struct vlan_group *vlgrp;
+#endif
+};
+
+extern int stmmac_mdio_unregister(struct net_device *ndev);
+extern int stmmac_mdio_register(struct net_device *ndev);
+extern void stmmac_set_ethtool_ops(struct net_device *netdev);
diff --git a/drivers/net/stmmac/stmmac_ethtool.c b/drivers/net/stmmac/stmmac_ethtool.c
new file mode 100644
index 0000000..694ebe6
--- /dev/null
+++ b/drivers/net/stmmac/stmmac_ethtool.c
@@ -0,0 +1,395 @@
+/*******************************************************************************
+  STMMAC Ethtool support
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include "stmmac.h"
+
+#define REG_SPACE_SIZE	0x1054
+#define MAC100_ETHTOOL_NAME	"st_mac100"
+#define GMAC_ETHTOOL_NAME	"st_gmac"
+
+struct stmmac_stats {
+	char stat_string[ETH_GSTRING_LEN];
+	int sizeof_stat;
+	int stat_offset;
+};
+
+#define STMMAC_STAT(m)	\
+	{ #m, FIELD_SIZEOF(struct stmmac_extra_stats, m),	\
+	offsetof(struct stmmac_priv, xstats.m)}
+
+static const struct  stmmac_stats stmmac_gstrings_stats[] = {
+	STMMAC_STAT(tx_underflow),
+	STMMAC_STAT(tx_carrier),
+	STMMAC_STAT(tx_losscarrier),
+	STMMAC_STAT(tx_heartbeat),
+	STMMAC_STAT(tx_deferred),
+	STMMAC_STAT(tx_vlan),
+	STMMAC_STAT(rx_vlan),
+	STMMAC_STAT(tx_jabber),
+	STMMAC_STAT(tx_frame_flushed),
+	STMMAC_STAT(tx_payload_error),
+	STMMAC_STAT(tx_ip_header_error),
+	STMMAC_STAT(rx_desc),
+	STMMAC_STAT(rx_partial),
+	STMMAC_STAT(rx_runt),
+	STMMAC_STAT(rx_toolong),
+	STMMAC_STAT(rx_collision),
+	STMMAC_STAT(rx_crc),
+	STMMAC_STAT(rx_lenght),
+	STMMAC_STAT(rx_mii),
+	STMMAC_STAT(rx_multicast),
+	STMMAC_STAT(rx_gmac_overflow),
+	STMMAC_STAT(rx_watchdog),
+	STMMAC_STAT(da_rx_filter_fail),
+	STMMAC_STAT(sa_rx_filter_fail),
+	STMMAC_STAT(rx_missed_cntr),
+	STMMAC_STAT(rx_overflow_cntr),
+	STMMAC_STAT(tx_undeflow_irq),
+	STMMAC_STAT(tx_process_stopped_irq),
+	STMMAC_STAT(tx_jabber_irq),
+	STMMAC_STAT(rx_overflow_irq),
+	STMMAC_STAT(rx_buf_unav_irq),
+	STMMAC_STAT(rx_process_stopped_irq),
+	STMMAC_STAT(rx_watchdog_irq),
+	STMMAC_STAT(tx_early_irq),
+	STMMAC_STAT(fatal_bus_error_irq),
+	STMMAC_STAT(threshold),
+	STMMAC_STAT(tx_pkt_n),
+	STMMAC_STAT(rx_pkt_n),
+	STMMAC_STAT(poll_n),
+	STMMAC_STAT(sched_timer_n),
+	STMMAC_STAT(normal_irq_n),
+};
+#define STMMAC_STATS_LEN ARRAY_SIZE(stmmac_gstrings_stats)
+
+void stmmac_ethtool_getdrvinfo(struct net_device *dev,
+			       struct ethtool_drvinfo *info)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	if (!priv->is_gmac)
+		strcpy(info->driver, MAC100_ETHTOOL_NAME);
+	else
+		strcpy(info->driver, GMAC_ETHTOOL_NAME);
+
+	strcpy(info->version, DRV_MODULE_VERSION);
+	info->fw_version[0] = '\0';
+	info->n_stats = STMMAC_STATS_LEN;
+	return;
+}
+
+int stmmac_ethtool_getsettings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	struct phy_device *phy = priv->phydev;
+	int rc;
+	if (phy == NULL) {
+		pr_err("%s: %s: PHY is not registered\n",
+		       __func__, dev->name);
+		return -ENODEV;
+	}
+	if (!netif_running(dev)) {
+		pr_err("%s: interface is disabled: we cannot track "
+		"link speed / duplex setting\n", dev->name);
+		return -EBUSY;
+	}
+	cmd->transceiver = XCVR_INTERNAL;
+	spin_lock_irq(&priv->lock);
+	rc = phy_ethtool_gset(phy, cmd);
+	spin_unlock_irq(&priv->lock);
+	return rc;
+}
+
+int stmmac_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	struct phy_device *phy = priv->phydev;
+	int rc;
+
+	spin_lock(&priv->lock);
+	rc = phy_ethtool_sset(phy, cmd);
+	spin_unlock(&priv->lock);
+
+	return rc;
+}
+
+u32 stmmac_ethtool_getmsglevel(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	return priv->msg_enable;
+}
+
+void stmmac_ethtool_setmsglevel(struct net_device *dev, u32 level)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	priv->msg_enable = level;
+
+}
+
+int stmmac_check_if_running(struct net_device *dev)
+{
+	if (!netif_running(dev))
+		return -EBUSY;
+	return 0;
+}
+
+int stmmac_ethtool_get_regs_len(struct net_device *dev)
+{
+	return REG_SPACE_SIZE;
+}
+
+void stmmac_ethtool_gregs(struct net_device *dev,
+			  struct ethtool_regs *regs, void *space)
+{
+	int i;
+	u32 *reg_space = (u32 *) space;
+
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	memset(reg_space, 0x0, REG_SPACE_SIZE);
+
+	if (!priv->is_gmac) {
+		/* MAC registers */
+		for (i = 0; i < 12; i++)
+			reg_space[i] = readl(dev->base_addr + (i * 4));
+		/* DMA registers */
+		for (i = 0; i < 9; i++)
+			reg_space[i + 12] =
+			    readl(dev->base_addr + (DMA_BUS_MODE + (i * 4)));
+		reg_space[22] = readl(dev->base_addr + DMA_CUR_TX_BUF_ADDR);
+		reg_space[23] = readl(dev->base_addr + DMA_CUR_RX_BUF_ADDR);
+	} else {
+		/* MAC registers */
+		for (i = 0; i < 55; i++)
+			reg_space[i] = readl(dev->base_addr + (i * 4));
+		/* DMA registers */
+		for (i = 0; i < 22; i++)
+			reg_space[i + 55] =
+			    readl(dev->base_addr + (DMA_BUS_MODE + (i * 4)));
+	}
+
+	return;
+}
+
+int stmmac_ethtool_set_tx_csum(struct net_device *netdev, u32 data)
+{
+	if (data)
+		netdev->features |= NETIF_F_HW_CSUM;
+	else
+		netdev->features &= ~NETIF_F_HW_CSUM;
+
+	return 0;
+}
+
+u32 stmmac_ethtool_get_rx_csum(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	return priv->rx_csum;
+}
+
+static void
+stmmac_get_pauseparam(struct net_device *netdev,
+		      struct ethtool_pauseparam *pause)
+{
+	struct stmmac_priv *priv = netdev_priv(netdev);
+
+	spin_lock(&priv->lock);
+
+	pause->rx_pause = 0;
+	pause->tx_pause = 0;
+	pause->autoneg = priv->phydev->autoneg;
+
+	if (priv->flow_ctrl & FLOW_RX)
+		pause->rx_pause = 1;
+	if (priv->flow_ctrl & FLOW_TX)
+		pause->tx_pause = 1;
+
+	spin_unlock(&priv->lock);
+	return;
+}
+
+static int
+stmmac_set_pauseparam(struct net_device *netdev,
+		      struct ethtool_pauseparam *pause)
+{
+	struct stmmac_priv *priv = netdev_priv(netdev);
+	struct phy_device *phy = priv->phydev;
+	int new_pause = FLOW_OFF;
+	int ret = 0;
+
+	spin_lock(&priv->lock);
+
+	if (pause->rx_pause)
+		new_pause |= FLOW_RX;
+	if (pause->tx_pause)
+		new_pause |= FLOW_TX;
+
+	priv->flow_ctrl = new_pause;
+
+	if (phy->autoneg) {
+		if (netif_running(netdev)) {
+			struct ethtool_cmd cmd;
+			/* auto-negotiation automatically restarted */
+			cmd.cmd = ETHTOOL_NWAY_RST;
+			cmd.supported = phy->supported;
+			cmd.advertising = phy->advertising;
+			cmd.autoneg = phy->autoneg;
+			cmd.speed = phy->speed;
+			cmd.duplex = phy->duplex;
+			cmd.phy_address = phy->addr;
+			ret = phy_ethtool_sset(phy, &cmd);
+		}
+	} else {
+		unsigned long ioaddr = netdev->base_addr;
+		priv->mac_type->ops->flow_ctrl(ioaddr, phy->duplex,
+					       priv->flow_ctrl, priv->pause);
+	}
+	spin_unlock(&priv->lock);
+	return ret;
+}
+
+static void stmmac_get_ethtool_stats(struct net_device *dev,
+				 struct ethtool_stats *dummy, u64 *data)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	unsigned long ioaddr = dev->base_addr;
+	int i;
+
+	/* Update HW stats if supported */
+	priv->mac_type->ops->dma_diagnostic_fr(&dev->stats, &priv->xstats,
+					       ioaddr);
+
+	for (i = 0; i < STMMAC_STATS_LEN; i++) {
+		char *p = (char *)priv + stmmac_gstrings_stats[i].stat_offset;
+		data[i] = (stmmac_gstrings_stats[i].sizeof_stat ==
+		sizeof(u64)) ? (*(u64 *)p) : (*(u32 *)p);
+	}
+
+	return;
+}
+
+static int stmmac_get_sset_count(struct net_device *netdev, int sset)
+{
+	switch (sset) {
+	case ETH_SS_STATS:
+		return STMMAC_STATS_LEN;
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static void stmmac_get_strings(struct net_device *dev, u32 stringset, u8 *data)
+{
+	int i;
+	u8 *p = data;
+
+	switch (stringset) {
+	case ETH_SS_STATS:
+		for (i = 0; i < STMMAC_STATS_LEN; i++) {
+			memcpy(p, stmmac_gstrings_stats[i].stat_string,
+				ETH_GSTRING_LEN);
+			p += ETH_GSTRING_LEN;
+		}
+		break;
+	default:
+		WARN_ON(1);
+		break;
+	}
+	return;
+}
+
+/* Currently only support WOL through Magic packet. */
+static void stmmac_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	spin_lock_irq(&priv->lock);
+	if (priv->wolenabled == PMT_SUPPORTED) {
+		wol->supported = WAKE_MAGIC;
+		wol->wolopts = priv->wolopts;
+	}
+	spin_unlock_irq(&priv->lock);
+}
+
+static int stmmac_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	u32 support = WAKE_MAGIC;
+
+	if (priv->wolenabled == PMT_NOT_SUPPORTED)
+		return -EINVAL;
+
+	if (wol->wolopts & ~support)
+		return -EINVAL;
+
+	if (wol->wolopts == 0)
+		device_set_wakeup_enable(priv->device, 0);
+	else
+		device_set_wakeup_enable(priv->device, 1);
+
+	spin_lock_irq(&priv->lock);
+	priv->wolopts = wol->wolopts;
+	spin_unlock_irq(&priv->lock);
+
+	return 0;
+}
+
+static struct ethtool_ops stmmac_ethtool_ops = {
+	.begin = stmmac_check_if_running,
+	.get_drvinfo = stmmac_ethtool_getdrvinfo,
+	.get_settings = stmmac_ethtool_getsettings,
+	.set_settings = stmmac_ethtool_setsettings,
+	.get_msglevel = stmmac_ethtool_getmsglevel,
+	.set_msglevel = stmmac_ethtool_setmsglevel,
+	.get_regs = stmmac_ethtool_gregs,
+	.get_regs_len = stmmac_ethtool_get_regs_len,
+	.get_link = ethtool_op_get_link,
+	.get_rx_csum = stmmac_ethtool_get_rx_csum,
+	.get_tx_csum = ethtool_op_get_tx_csum,
+	.set_tx_csum = stmmac_ethtool_set_tx_csum,
+	.get_sg = ethtool_op_get_sg,
+	.set_sg = ethtool_op_set_sg,
+	.get_pauseparam = stmmac_get_pauseparam,
+	.set_pauseparam = stmmac_set_pauseparam,
+	.get_ethtool_stats = stmmac_get_ethtool_stats,
+	.get_strings = stmmac_get_strings,
+	.get_wol = stmmac_get_wol,
+	.set_wol = stmmac_set_wol,
+	.get_sset_count	= stmmac_get_sset_count,
+#ifdef NETIF_F_TSO
+	.get_tso = ethtool_op_get_tso,
+	.set_tso = ethtool_op_set_tso,
+#endif
+};
+
+void stmmac_set_ethtool_ops(struct net_device *netdev)
+{
+	SET_ETHTOOL_OPS(netdev, &stmmac_ethtool_ops);
+}
diff --git a/drivers/net/stmmac/stmmac_main.c b/drivers/net/stmmac/stmmac_main.c
new file mode 100644
index 0000000..c2f14dc
--- /dev/null
+++ b/drivers/net/stmmac/stmmac_main.c
@@ -0,0 +1,2204 @@
+/*******************************************************************************
+  This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers.
+  ST Ethernet IPs are built around a Synopsys IP Core.
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+
+  Documentation available at:
+	http://www.stlinux.com
+  Support available at:
+	https://bugzilla.stlinux.com/
+*******************************************************************************/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/ip.h>
+#include <linux/tcp.h>
+#include <linux/skbuff.h>
+#include <linux/ethtool.h>
+#include <linux/if_ether.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/if_vlan.h>
+#include <linux/dma-mapping.h>
+#include <linux/stm/soc.h>
+#include "stmmac.h"
+
+#define STMMAC_RESOURCE_NAME	"stmmaceth"
+#define PHY_RESOURCE_NAME	"stmmacphy"
+
+#undef STMMAC_DEBUG
+/*#define STMMAC_DEBUG*/
+#ifdef STMMAC_DEBUG
+#define DBG(nlevel, klevel, fmt, args...) \
+		((void)(netif_msg_##nlevel(priv) && \
+		printk(KERN_##klevel fmt, ## args)))
+#else
+#define DBG(nlevel, klevel, fmt, args...) do { } while (0)
+#endif
+
+#undef STMMAC_RX_DEBUG
+/*#define STMMAC_RX_DEBUG*/
+#ifdef STMMAC_RX_DEBUG
+#define RX_DBG(fmt, args...)  printk(fmt, ## args)
+#else
+#define RX_DBG(fmt, args...)  do { } while (0)
+#endif
+
+#undef STMMAC_XMIT_DEBUG
+/*#define STMMAC_XMIT_DEBUG*/
+#ifdef STMMAC_TX_DEBUG
+#define TX_DBG(fmt, args...)  printk(fmt, ## args)
+#else
+#define TX_DBG(fmt, args...)  do { } while (0)
+#endif
+
+#define STMMAC_ALIGN(x)	L1_CACHE_ALIGN(x)
+#define JUMBO_LEN	9000
+
+/* Module parameters */
+#define TX_TIMEO 5000 /* default 5 seconds */
+static int watchdog = TX_TIMEO;
+module_param(watchdog, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(watchdog, "Transmit timeout in milliseconds");
+
+static int debug = -1;		/* -1: default, 0: no output, 16:  all */
+module_param(debug, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Message Level (0: no output, 16: all)");
+
+static int phyaddr = -1;
+module_param(phyaddr, int, S_IRUGO);
+MODULE_PARM_DESC(phyaddr, "Physical device address");
+
+#define DMA_TX_SIZE 256
+static int dma_txsize = DMA_TX_SIZE;
+module_param(dma_txsize, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(dma_txsize, "Number of descriptors in the TX list");
+
+#define DMA_RX_SIZE 256
+static int dma_rxsize = DMA_RX_SIZE;
+module_param(dma_rxsize, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(dma_rxsize, "Number of descriptors in the RX list");
+
+static int flow_ctrl = FLOW_OFF;
+module_param(flow_ctrl, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(flow_ctrl, "Flow control ability [on/off]");
+
+static int pause = PAUSE_TIME;
+module_param(pause, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(pause, "Flow Control Pause Time");
+
+#define TC_DEFAULT 64
+static int tc = TC_DEFAULT;
+module_param(tc, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(tc, "DMA threshold control value");
+
+#define RX_NO_COALESCE	1	/* Always interrupt on completion */
+#define TX_NO_COALESCE	-1	/* No moderation by default */
+
+/* Pay attention to tune this parameter; take care of both
+ * hardware capability and network stabitily/performance impact.
+ * Many tests showed that ~4ms latency seems to be good enough. */
+#ifdef CONFIG_STMMAC_TIMER
+#define DEFAULT_PERIODIC_RATE	256
+static int tmrate = DEFAULT_PERIODIC_RATE;
+module_param(tmrate, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(tmrate, "External timer freq. (default: 256Hz)");
+#endif
+
+#define DMA_BUFFER_SIZE	BUF_SIZE_2KiB
+static int buf_sz = DMA_BUFFER_SIZE;
+module_param(buf_sz, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(buf_sz, "DMA buffer size");
+
+/* In case of Giga ETH, we can enable/disable the COE for the
+ * transmit HW checksum computation.
+ * Note that, if tx csum is off in HW, SG will be still supported. */
+static int tx_coe = HW_CSUM;
+module_param(tx_coe, int, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(tx_coe, "GMAC COE type 2 [on/off]");
+
+static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
+				      NETIF_MSG_LINK | NETIF_MSG_IFUP |
+				      NETIF_MSG_IFDOWN | NETIF_MSG_TIMER);
+
+static irqreturn_t stmmac_interrupt(int irq, void *dev_id);
+static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev);
+
+/**
+ * stmmac_verify_args - verify the driver parameters.
+ * Description: it verifies if some wrong parameter is passed to the driver.
+ * Note that wrong parameters are replaced with the default values.
+ */
+static void stmmac_verify_args(void)
+{
+	if (unlikely(watchdog < 0))
+		watchdog = TX_TIMEO;
+	if (unlikely(dma_rxsize < 0))
+		dma_rxsize = DMA_RX_SIZE;
+	if (unlikely(dma_txsize < 0))
+		dma_txsize = DMA_TX_SIZE;
+	if (unlikely((buf_sz < DMA_BUFFER_SIZE) || (buf_sz > BUF_SIZE_16KiB)))
+		buf_sz = DMA_BUFFER_SIZE;
+	if (unlikely(flow_ctrl > 1))
+		flow_ctrl = FLOW_AUTO;
+	else if (likely(flow_ctrl < 0))
+		flow_ctrl = FLOW_OFF;
+	if (unlikely((pause < 0) || (pause > 0xffff)))
+		pause = PAUSE_TIME;
+
+	return;
+}
+
+#if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
+static void print_pkt(unsigned char *buf, int len)
+{
+	int j;
+	pr_info("len = %d byte, buf addr: 0x%p", len, buf);
+	for (j = 0; j < len; j++) {
+		if ((j % 16) == 0)
+			pr_info("\n %03x:", j);
+		pr_info(" %02x", buf[j]);
+	}
+	pr_info("\n");
+	return;
+}
+#endif
+
+/* minimum number of free TX descriptors required to wake up TX process */
+#define STMMAC_TX_THRESH(x)	(x->dma_tx_size/4)
+
+static inline u32 stmmac_tx_avail(struct stmmac_priv *priv)
+{
+	return priv->dirty_tx + priv->dma_tx_size - priv->cur_tx - 1;
+}
+
+/**
+ * stmmac_adjust_link
+ * @dev: net device structure
+ * Description: it adjusts the link parameters.
+ */
+static void stmmac_adjust_link(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	struct phy_device *phydev = priv->phydev;
+	unsigned long ioaddr = dev->base_addr;
+	unsigned long flags;
+	int new_state = 0;
+	unsigned int fc = priv->flow_ctrl, pause_time = priv->pause;
+
+	if (phydev == NULL)
+		return;
+
+	DBG(probe, DEBUG, "stmmac_adjust_link: called.  address %d link %d\n",
+	    phydev->addr, phydev->link);
+
+	spin_lock_irqsave(&priv->lock, flags);
+	if (phydev->link) {
+		u32 ctrl = readl(ioaddr + MAC_CTRL_REG);
+
+		/* Now we make sure that we can be in full duplex mode.
+		 * If not, we operate in half-duplex mode. */
+		if (phydev->duplex != priv->oldduplex) {
+			new_state = 1;
+			if (!(phydev->duplex))
+				ctrl &= ~priv->mac_type->hw.link.duplex;
+			else
+				ctrl |= priv->mac_type->hw.link.duplex;
+			priv->oldduplex = phydev->duplex;
+		}
+		/* Flow Control operation */
+		if (phydev->pause)
+			priv->mac_type->ops->flow_ctrl(ioaddr, phydev->duplex,
+						       fc, pause_time);
+
+		if (phydev->speed != priv->speed) {
+			new_state = 1;
+			switch (phydev->speed) {
+			case 1000:
+				if (likely(priv->is_gmac))
+					ctrl &= ~priv->mac_type->hw.link.port;
+				break;
+			case 100:
+			case 10:
+				if (priv->is_gmac) {
+					ctrl |= priv->mac_type->hw.link.port;
+					if (phydev->speed == SPEED_100) {
+						ctrl |=
+						    priv->mac_type->hw.link.
+						    speed;
+					} else {
+						ctrl &=
+						    ~(priv->mac_type->hw.
+						      link.speed);
+					}
+				} else {
+					ctrl &= ~priv->mac_type->hw.link.port;
+				}
+				priv->fix_mac_speed(priv->bsp_priv,
+						    phydev->speed);
+				break;
+			default:
+				if (netif_msg_link(priv))
+					pr_warning("%s: Speed (%d) is not 10"
+				       " or 100!\n", dev->name, phydev->speed);
+				break;
+			}
+
+			priv->speed = phydev->speed;
+		}
+
+		writel(ctrl, ioaddr + MAC_CTRL_REG);
+
+		if (!priv->oldlink) {
+			new_state = 1;
+			priv->oldlink = 1;
+		}
+	} else if (priv->oldlink) {
+		new_state = 1;
+		priv->oldlink = 0;
+		priv->speed = 0;
+		priv->oldduplex = -1;
+	}
+
+	if (new_state && netif_msg_link(priv))
+		phy_print_status(phydev);
+
+	spin_unlock_irqrestore(&priv->lock, flags);
+
+	DBG(probe, DEBUG, "stmmac_adjust_link: exiting\n");
+}
+
+/**
+ * stmmac_init_phy - PHY initialization
+ * @dev: net device structure
+ * Description: it initializes the driver's PHY state, and attaches the PHY
+ * to the mac driver.
+ *  Return value:
+ *  0 on success
+ */
+static int stmmac_init_phy(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	struct phy_device *phydev;
+	char phy_id[BUS_ID_SIZE];	/* PHY to connect */
+	char bus_id[BUS_ID_SIZE];
+
+	priv->oldlink = 0;
+	priv->speed = 0;
+	priv->oldduplex = -1;
+
+	if (priv->phy_addr == -1) {
+		/* We don't have a PHY, so do nothing */
+		return 0;
+	}
+
+	snprintf(bus_id, MII_BUS_ID_SIZE, "%x", priv->bus_id);
+	snprintf(phy_id, BUS_ID_SIZE, PHY_ID_FMT, bus_id, priv->phy_addr);
+	pr_debug("stmmac_init_phy:  trying to attach to %s\n", phy_id);
+
+	phydev = phy_connect(dev, phy_id, &stmmac_adjust_link, 0,
+			priv->phy_interface);
+
+	if (IS_ERR(phydev)) {
+		pr_err("%s: Could not attach to PHY\n", dev->name);
+		return PTR_ERR(phydev);
+	}
+
+	/*
+	 * Broken HW is sometimes missing the pull-up resistor on the
+	 * MDIO line, which results in reads to non-existent devices returning
+	 * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
+	 * device as well.
+	 * Note: phydev->phy_id is the result of reading the UID PHY registers.
+	 */
+	if (phydev->phy_id == 0) {
+		phy_disconnect(phydev);
+		return -ENODEV;
+	}
+	pr_debug("stmmac_init_phy:  %s: attached to PHY (UID 0x%x)"
+	       " Link = %d\n", dev->name, phydev->phy_id, phydev->link);
+
+	priv->phydev = phydev;
+
+	return 0;
+}
+
+static inline void stmmac_mac_enable_rx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + MAC_CTRL_REG);
+	value |= MAC_RNABLE_RX;
+	/* Set the RE (receive enable bit into the MAC CTRL register).  */
+	writel(value, ioaddr + MAC_CTRL_REG);
+}
+
+static inline void stmmac_mac_enable_tx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + MAC_CTRL_REG);
+	value |= MAC_ENABLE_TX;
+	/* Set the TE (transmit enable bit into the MAC CTRL register).  */
+	writel(value, ioaddr + MAC_CTRL_REG);
+}
+
+static inline void stmmac_mac_disable_rx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + MAC_CTRL_REG);
+	value &= ~MAC_RNABLE_RX;
+	writel(value, ioaddr + MAC_CTRL_REG);
+}
+
+static inline void stmmac_mac_disable_tx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + MAC_CTRL_REG);
+	value &= ~MAC_ENABLE_TX;
+	writel(value, ioaddr + MAC_CTRL_REG);
+}
+
+/**
+ * display_ring
+ * @p: pointer to the ring.
+ * @size: size of the ring.
+ * Description: display all the descriptors within the ring.
+ */
+static void display_ring(struct dma_desc *p, int size)
+{
+	struct tmp_s {
+		u64 a;
+		unsigned int b;
+		unsigned int c;
+	};
+	int i;
+	for (i = 0; i < size; i++) {
+		struct tmp_s *x = (struct tmp_s *)(p + i);
+		pr_info("\t%d [0x%x]: DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
+		       i, (unsigned int)virt_to_phys(&p[i]),
+		       (unsigned int)(x->a), (unsigned int)((x->a) >> 32),
+		       x->b, x->c);
+		pr_info("\n");
+	}
+}
+
+/**
+ * init_dma_desc_rings - init the RX/TX descriptor rings
+ * @dev: net device structure
+ * Description:  this function initializes the DMA RX/TX descriptors
+ * and allocates the socket buffers.
+ */
+static void init_dma_desc_rings(struct net_device *dev)
+{
+	int i;
+	struct stmmac_priv *priv = netdev_priv(dev);
+	struct sk_buff *skb;
+	unsigned int txsize = priv->dma_tx_size;
+	unsigned int rxsize = priv->dma_rx_size;
+	unsigned int bfsize = priv->dma_buf_sz;
+	int buff2_needed = 0;
+	int dis_ic = 0;
+
+#ifdef CONFIG_STMMAC_TIMER
+	/* Using Timers disable interrupts on completion for the reception */
+	dis_ic = 1;
+#endif
+	/* Set the Buffer size according to the MTU;
+	 * indeed, in case of jumbo we need to bump-up the buffer sizes.
+	 */
+	if (unlikely(dev->mtu >= BUF_SIZE_8KiB))
+		bfsize = BUF_SIZE_16KiB;
+	else if (unlikely(dev->mtu >= BUF_SIZE_4KiB))
+		bfsize = BUF_SIZE_8KiB;
+	else if (unlikely(dev->mtu >= BUF_SIZE_2KiB))
+		bfsize = BUF_SIZE_4KiB;
+	else if (unlikely(dev->mtu >= DMA_BUFFER_SIZE))
+		bfsize = BUF_SIZE_2KiB;
+	else
+		bfsize = DMA_BUFFER_SIZE;
+
+	/* If the MTU exceeds 8k so use the second buffer in the chain */
+	if (bfsize >= BUF_SIZE_8KiB)
+		buff2_needed = 1;
+
+	DBG(probe, INFO, "stmmac: txsize %d, rxsize %d, bfsize %d\n",
+	    txsize, rxsize, bfsize);
+
+	priv->rx_skbuff_dma = kmalloc(rxsize * sizeof(dma_addr_t), GFP_KERNEL);
+	priv->rx_skbuff =
+	    kmalloc(sizeof(struct sk_buff *) * rxsize, GFP_KERNEL);
+	priv->dma_rx =
+	    (struct dma_desc *)dma_alloc_coherent(priv->device,
+						  rxsize *
+						  sizeof(struct dma_desc),
+						  &priv->dma_rx_phy,
+						  GFP_KERNEL);
+	priv->tx_skbuff = kmalloc(sizeof(struct sk_buff *) * txsize,
+				       GFP_KERNEL);
+	priv->dma_tx =
+	    (struct dma_desc *)dma_alloc_coherent(priv->device,
+						  txsize *
+						  sizeof(struct dma_desc),
+						  &priv->dma_tx_phy,
+						  GFP_KERNEL);
+
+	if ((priv->dma_rx == NULL) || (priv->dma_tx == NULL)) {
+		pr_err("%s:ERROR allocating the DMA Tx/Rx desc\n", __func__);
+		return;
+	}
+
+	DBG(probe, INFO, "stmmac (%s) DMA desc rings: virt addr (Rx %p, "
+	    "Tx %p)\n\tDMA phy addr (Rx 0x%08x, Tx 0x%08x)\n",
+	    dev->name, priv->dma_rx, priv->dma_tx,
+	    (unsigned int)priv->dma_rx_phy, (unsigned int)priv->dma_tx_phy);
+
+	/* RX INITIALIZATION */
+	DBG(probe, INFO, "stmmac: SKB addresses:\n"
+			 "skb\t\tskb data\tdma data\n");
+
+	for (i = 0; i < rxsize; i++) {
+		struct dma_desc *p = priv->dma_rx + i;
+
+		skb = netdev_alloc_skb_ip_align(dev, bfsize);
+		if (unlikely(skb == NULL)) {
+			pr_err("%s: Rx init fails; skb is NULL\n", __func__);
+			break;
+		}
+		priv->rx_skbuff[i] = skb;
+		priv->rx_skbuff_dma[i] = dma_map_single(priv->device, skb->data,
+						bfsize, DMA_FROM_DEVICE);
+
+		p->des2 = priv->rx_skbuff_dma[i];
+		if (unlikely(buff2_needed))
+			p->des3 = p->des2 + BUF_SIZE_8KiB;
+		DBG(probe, INFO, "[%p]\t[%p]\t[%x]\n", priv->rx_skbuff[i],
+			priv->rx_skbuff[i]->data, priv->rx_skbuff_dma[i]);
+	}
+	priv->cur_rx = 0;
+	priv->dirty_rx = (unsigned int)(i - rxsize);
+	priv->dma_buf_sz = bfsize;
+	buf_sz = bfsize;
+
+	/* TX INITIALIZATION */
+	for (i = 0; i < txsize; i++) {
+		priv->tx_skbuff[i] = NULL;
+		priv->dma_tx[i].des2 = 0;
+	}
+	priv->dirty_tx = 0;
+	priv->cur_tx = 0;
+
+	/* Clear the Rx/Tx descriptors */
+	priv->mac_type->ops->init_rx_desc(priv->dma_rx, rxsize, dis_ic);
+	priv->mac_type->ops->init_tx_desc(priv->dma_tx, txsize);
+
+	if (netif_msg_hw(priv)) {
+		pr_info("RX descriptor ring:\n");
+		display_ring(priv->dma_rx, rxsize);
+		pr_info("TX descriptor ring:\n");
+		display_ring(priv->dma_tx, txsize);
+	}
+	return;
+}
+
+static void dma_free_rx_skbufs(struct stmmac_priv *priv)
+{
+	int i;
+
+	for (i = 0; i < priv->dma_rx_size; i++) {
+		if (priv->rx_skbuff[i]) {
+			dma_unmap_single(priv->device, priv->rx_skbuff_dma[i],
+					 priv->dma_buf_sz, DMA_FROM_DEVICE);
+			dev_kfree_skb_any(priv->rx_skbuff[i]);
+		}
+		priv->rx_skbuff[i] = NULL;
+	}
+	return;
+}
+
+static void dma_free_tx_skbufs(struct stmmac_priv *priv)
+{
+	int i;
+
+	for (i = 0; i < priv->dma_tx_size; i++) {
+		if (priv->tx_skbuff[i] != NULL) {
+			struct dma_desc *p = priv->dma_tx + i;
+			if (p->des2)
+				dma_unmap_single(priv->device, p->des2,
+				 priv->mac_type->ops->get_tx_len(p),
+				 DMA_TO_DEVICE);
+			dev_kfree_skb_any(priv->tx_skbuff[i]);
+			priv->tx_skbuff[i] = NULL;
+		}
+	}
+	return;
+}
+
+static void free_dma_desc_resources(struct stmmac_priv *priv)
+{
+	/* Release the DMA TX/RX socket buffers */
+	dma_free_rx_skbufs(priv);
+	dma_free_tx_skbufs(priv);
+
+	/* Free the region of consistent memory previously allocated for
+	 * the DMA */
+	dma_free_coherent(priv->device,
+			  priv->dma_tx_size * sizeof(struct dma_desc),
+			  priv->dma_tx, priv->dma_tx_phy);
+	dma_free_coherent(priv->device,
+			  priv->dma_rx_size * sizeof(struct dma_desc),
+			  priv->dma_rx, priv->dma_rx_phy);
+	kfree(priv->rx_skbuff_dma);
+	kfree(priv->rx_skbuff);
+	kfree(priv->tx_skbuff);
+
+	return;
+}
+
+/**
+ * stmmac_dma_start_tx
+ * @ioaddr: device I/O address
+ * Description:  this function starts the DMA tx process.
+ */
+static void stmmac_dma_start_tx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + DMA_CONTROL);
+	value |= DMA_CONTROL_ST;
+	writel(value, ioaddr + DMA_CONTROL);
+	return;
+}
+
+static void stmmac_dma_stop_tx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + DMA_CONTROL);
+	value &= ~DMA_CONTROL_ST;
+	writel(value, ioaddr + DMA_CONTROL);
+	return;
+}
+
+/**
+ * stmmac_dma_start_rx
+ * @ioaddr: device I/O address
+ * Description:  this function starts the DMA rx process.
+ */
+static void stmmac_dma_start_rx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + DMA_CONTROL);
+	value |= DMA_CONTROL_SR;
+	writel(value, ioaddr + DMA_CONTROL);
+
+	return;
+}
+
+static void stmmac_dma_stop_rx(unsigned long ioaddr)
+{
+	u32 value = readl(ioaddr + DMA_CONTROL);
+	value &= ~DMA_CONTROL_SR;
+	writel(value, ioaddr + DMA_CONTROL);
+
+	return;
+}
+
+/**
+ *  stmmac_dma_operation_mode - HW DMA operation mode
+ *  @priv : pointer to the private device structure.
+ *  Description: it sets the DMA operation mode: tx/rx DMA thresholds
+ *  or Store-And-Forward capability. It also verifies the COE for the
+ *  transmission in case of Giga ETH.
+ */
+static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
+{
+	if (!priv->is_gmac) {
+		/* MAC 10/100 */
+		priv->mac_type->ops->dma_mode(priv->dev->base_addr, tc, 0);
+		priv->tx_coe = NO_HW_CSUM;
+	} else {
+		if ((priv->dev->mtu <= ETH_DATA_LEN) && (tx_coe)) {
+			priv->mac_type->ops->dma_mode(priv->dev->base_addr,
+						      SF_DMA_MODE, SF_DMA_MODE);
+			tc = SF_DMA_MODE;
+			priv->tx_coe = HW_CSUM;
+		} else {
+			/* Checksum computation is performed in software. */
+			priv->mac_type->ops->dma_mode(priv->dev->base_addr, tc,
+						      SF_DMA_MODE);
+			priv->tx_coe = NO_HW_CSUM;
+		}
+	}
+	tx_coe = priv->tx_coe;
+
+	return;
+}
+
+#ifdef STMMAC_DEBUG
+/**
+ * show_tx_process_state
+ * @status: tx descriptor status field
+ * Description: it shows the Transmit Process State for CSR5[22:20]
+ */
+static void show_tx_process_state(unsigned int status)
+{
+	unsigned int state;
+	state = (status & DMA_STATUS_TS_MASK) >> DMA_STATUS_TS_SHIFT;
+
+	switch (state) {
+	case 0:
+		pr_info("- TX (Stopped): Reset or Stop command\n");
+		break;
+	case 1:
+		pr_info("- TX (Running):Fetching the Tx desc\n");
+		break;
+	case 2:
+		pr_info("- TX (Running): Waiting for end of tx\n");
+		break;
+	case 3:
+		pr_info("- TX (Running): Reading the data "
+		       "and queuing the data into the Tx buf\n");
+		break;
+	case 6:
+		pr_info("- TX (Suspended): Tx Buff Underflow "
+		       "or an unavailable Transmit descriptor\n");
+		break;
+	case 7:
+		pr_info("- TX (Running): Closing Tx descriptor\n");
+		break;
+	default:
+		break;
+	}
+	return;
+}
+
+/**
+ * show_rx_process_state
+ * @status: rx descriptor status field
+ * Description: it shows the  Receive Process State for CSR5[19:17]
+ */
+static void show_rx_process_state(unsigned int status)
+{
+	unsigned int state;
+	state = (status & DMA_STATUS_RS_MASK) >> DMA_STATUS_RS_SHIFT;
+
+	switch (state) {
+	case 0:
+		pr_info("- RX (Stopped): Reset or Stop command\n");
+		break;
+	case 1:
+		pr_info("- RX (Running): Fetching the Rx desc\n");
+		break;
+	case 2:
+		pr_info("- RX (Running):Checking for end of pkt\n");
+		break;
+	case 3:
+		pr_info("- RX (Running): Waiting for Rx pkt\n");
+		break;
+	case 4:
+		pr_info("- RX (Suspended): Unavailable Rx buf\n");
+		break;
+	case 5:
+		pr_info("- RX (Running): Closing Rx descriptor\n");
+		break;
+	case 6:
+		pr_info("- RX(Running): Flushing the current frame"
+		       " from the Rx buf\n");
+		break;
+	case 7:
+		pr_info("- RX (Running): Queuing the Rx frame"
+		       " from the Rx buf into memory\n");
+		break;
+	default:
+		break;
+	}
+	return;
+}
+#endif
+
+/**
+ * stmmac_tx:
+ * @priv: private driver structure
+ * Description: it reclaims resources after transmission completes.
+ */
+static void stmmac_tx(struct stmmac_priv *priv)
+{
+	unsigned int txsize = priv->dma_tx_size;
+	unsigned long ioaddr = priv->dev->base_addr;
+
+	while (priv->dirty_tx != priv->cur_tx) {
+		int last;
+		unsigned int entry = priv->dirty_tx % txsize;
+		struct sk_buff *skb = priv->tx_skbuff[entry];
+		struct dma_desc *p = priv->dma_tx + entry;
+
+		/* Check if the descriptor is owned by the DMA. */
+		if (priv->mac_type->ops->get_tx_owner(p))
+			break;
+
+		/* Verify tx error by looking at the last segment */
+		last = priv->mac_type->ops->get_tx_ls(p);
+		if (likely(last)) {
+			int tx_error =
+			    priv->mac_type->ops->tx_status(&priv->dev->stats,
+							   &priv->xstats,
+							   p, ioaddr);
+			if (likely(tx_error == 0)) {
+				priv->dev->stats.tx_packets++;
+				priv->xstats.tx_pkt_n++;
+			} else
+				priv->dev->stats.tx_errors++;
+		}
+		TX_DBG("%s: curr %d, dirty %d\n", __func__,
+			priv->cur_tx, priv->dirty_tx);
+
+		if (likely(p->des2))
+			dma_unmap_single(priv->device, p->des2,
+					 priv->mac_type->ops->get_tx_len(p),
+					 DMA_TO_DEVICE);
+		if (unlikely(p->des3))
+			p->des3 = 0;
+
+		if (likely(skb != NULL)) {
+			/*
+			 * If there's room in the queue (limit it to size)
+			 * we add this skb back into the pool,
+			 * if it's the right size.
+			 */
+			if ((skb_queue_len(&priv->rx_recycle) <
+				priv->dma_rx_size) &&
+				skb_recycle_check(skb, priv->dma_buf_sz))
+				__skb_queue_head(&priv->rx_recycle, skb);
+			else
+				dev_kfree_skb(skb);
+
+			priv->tx_skbuff[entry] = NULL;
+		}
+
+		priv->mac_type->ops->release_tx_desc(p);
+
+		entry = (++priv->dirty_tx) % txsize;
+	}
+	if (unlikely(netif_queue_stopped(priv->dev) &&
+		     stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv))) {
+		netif_tx_lock(priv->dev);
+		if (netif_queue_stopped(priv->dev) &&
+		     stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv)) {
+			TX_DBG("%s: restart transmit\n", __func__);
+			netif_wake_queue(priv->dev);
+		}
+		netif_tx_unlock(priv->dev);
+	}
+	return;
+}
+
+static inline void stmmac_enable_irq(struct stmmac_priv *priv)
+{
+#ifndef CONFIG_STMMAC_TIMER
+	writel(DMA_INTR_DEFAULT_MASK, priv->dev->base_addr + DMA_INTR_ENA);
+#else
+	priv->tm->timer_start(tmrate);
+#endif
+}
+
+static inline void stmmac_disable_irq(struct stmmac_priv *priv)
+{
+#ifndef CONFIG_STMMAC_TIMER
+	writel(0, priv->dev->base_addr + DMA_INTR_ENA);
+#else
+	priv->tm->timer_stop();
+#endif
+}
+
+static int stmmac_has_work(struct stmmac_priv *priv)
+{
+	unsigned int has_work = 0;
+	int rxret, tx_work = 0;
+
+	rxret = priv->mac_type->ops->get_rx_owner(priv->dma_rx +
+		(priv->cur_rx % priv->dma_rx_size));
+
+	if (priv->dirty_tx != priv->cur_tx)
+		tx_work = 1;
+
+	if (likely(!rxret || tx_work))
+		has_work = 1;
+
+	return has_work;
+}
+
+static inline void _stmmac_schedule(struct stmmac_priv *priv)
+{
+	if (likely(stmmac_has_work(priv))) {
+		stmmac_disable_irq(priv);
+		napi_schedule(&priv->napi);
+	}
+}
+
+#ifdef CONFIG_STMMAC_TIMER
+void stmmac_schedule(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	priv->xstats.sched_timer_n++;
+
+	_stmmac_schedule(priv);
+
+	return;
+}
+
+static void stmmac_no_timer_started(unsigned int x)
+{;
+};
+
+static void stmmac_no_timer_stopped(void)
+{;
+};
+#endif
+
+/**
+ * stmmac_tx_err:
+ * @priv: pointer to the private device structure
+ * Description: it cleans the descriptors and restarts the transmission
+ * in case of errors.
+ */
+static void stmmac_tx_err(struct stmmac_priv *priv)
+{
+	netif_stop_queue(priv->dev);
+
+	stmmac_dma_stop_tx(priv->dev->base_addr);
+	dma_free_tx_skbufs(priv);
+	priv->mac_type->ops->init_tx_desc(priv->dma_tx, priv->dma_tx_size);
+	priv->dirty_tx = 0;
+	priv->cur_tx = 0;
+	stmmac_dma_start_tx(priv->dev->base_addr);
+
+	priv->dev->stats.tx_errors++;
+	netif_wake_queue(priv->dev);
+
+	return;
+}
+
+/**
+ * stmmac_dma_interrupt - Interrupt handler for the driver
+ * @dev: net device structure
+ * Description: Interrupt handler for the driver (DMA).
+ */
+static void stmmac_dma_interrupt(struct net_device *dev)
+{
+	unsigned long ioaddr = dev->base_addr;
+	struct stmmac_priv *priv = netdev_priv(dev);
+	/* read the status register (CSR5) */
+	u32 intr_status = readl(ioaddr + DMA_STATUS);
+
+	DBG(intr, INFO, "%s: [CSR5: 0x%08x]\n", __func__, intr_status);
+
+#ifdef STMMAC_DEBUG
+	/* It displays the DMA transmit process state (CSR5 register) */
+	if (netif_msg_tx_done(priv))
+		show_tx_process_state(intr_status);
+	if (netif_msg_rx_status(priv))
+		show_rx_process_state(intr_status);
+#endif
+	/* ABNORMAL interrupts */
+	if (unlikely(intr_status & DMA_STATUS_AIS)) {
+		DBG(intr, INFO, "CSR5[15] DMA ABNORMAL IRQ: ");
+		if (unlikely(intr_status & DMA_STATUS_UNF)) {
+			DBG(intr, INFO, "transmit underflow\n");
+			if (unlikely(tc != SF_DMA_MODE)
+			    && (tc <= 256)) {
+				/* Try to bump up the threshold */
+				tc += 64;
+				priv->mac_type->ops->dma_mode(ioaddr, tc,
+					      SF_DMA_MODE);
+				priv->xstats.threshold = tc;
+			}
+			stmmac_tx_err(priv);
+			priv->xstats.tx_undeflow_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_TJT)) {
+			DBG(intr, INFO, "transmit jabber\n");
+			priv->xstats.tx_jabber_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_OVF)) {
+			DBG(intr, INFO, "recv overflow\n");
+			priv->xstats.rx_overflow_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_RU)) {
+			DBG(intr, INFO, "receive buffer unavailable\n");
+			priv->xstats.rx_buf_unav_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_RPS)) {
+			DBG(intr, INFO, "receive process stopped\n");
+			priv->xstats.rx_process_stopped_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_RWT)) {
+			DBG(intr, INFO, "receive watchdog\n");
+			priv->xstats.rx_watchdog_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_ETI)) {
+			DBG(intr, INFO, "transmit early interrupt\n");
+			priv->xstats.tx_early_irq++;
+		}
+		if (unlikely(intr_status & DMA_STATUS_TPS)) {
+			DBG(intr, INFO, "transmit process stopped\n");
+			priv->xstats.tx_process_stopped_irq++;
+			stmmac_tx_err(priv);
+		}
+		if (unlikely(intr_status & DMA_STATUS_FBI)) {
+			DBG(intr, INFO, "fatal bus error\n");
+			priv->xstats.fatal_bus_error_irq++;
+			stmmac_tx_err(priv);
+		}
+	}
+
+	/* TX/RX NORMAL interrupts */
+	if (intr_status & DMA_STATUS_NIS) {
+		priv->xstats.normal_irq_n++;
+		if (likely((intr_status & DMA_STATUS_RI) ||
+			 (intr_status & (DMA_STATUS_TI))))
+				_stmmac_schedule(priv);
+	}
+
+	/* Optional hardware blocks, interrupts should be disabled */
+	if (unlikely(intr_status &
+		     (DMA_STATUS_GPI | DMA_STATUS_GMI | DMA_STATUS_GLI)))
+		pr_info("%s: unexpected status %08x\n", __func__, intr_status);
+
+	/* Clear the interrupt by writing a logic 1 to the CSR5[15-0] */
+	writel((intr_status & 0x1ffff), ioaddr + DMA_STATUS);
+
+	DBG(intr, INFO, "\n\n");
+
+	return;
+}
+
+/**
+ *  stmmac_open - open entry point of the driver
+ *  @dev : pointer to the device structure.
+ *  Description:
+ *  This function is the open entry point of the driver.
+ *  Return value:
+ *  0 on success and an appropriate (-)ve integer as defined in errno.h
+ *  file on failure.
+ */
+static int stmmac_open(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	unsigned long ioaddr = dev->base_addr;
+	int ret;
+
+	/* Check that the MAC address is valid.  If its not, refuse
+	 * to bring the device up. The user must specify an
+	 * address using the following linux command:
+	 *      ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx  */
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		random_ether_addr(dev->dev_addr);
+		pr_warning("%s: generated random MAC address %pM\n", dev->name,
+			dev->dev_addr);
+	}
+
+	stmmac_verify_args();
+
+	ret = stmmac_init_phy(dev);
+	if (unlikely(ret)) {
+		pr_err("%s: Cannot attach to PHY (error: %d)\n", __func__, ret);
+		return ret;
+	}
+
+	/* Request the IRQ lines */
+	ret = request_irq(dev->irq, &stmmac_interrupt,
+			  IRQF_SHARED, dev->name, dev);
+	if (unlikely(ret < 0)) {
+		pr_err("%s: ERROR: allocating the IRQ %d (error: %d)\n",
+		       __func__, dev->irq, ret);
+		return ret;
+	}
+
+#ifdef CONFIG_STMMAC_TIMER
+	priv->tm = kmalloc(sizeof(struct stmmac_timer *), GFP_KERNEL);
+	if (unlikely(priv->tm == NULL)) {
+		pr_err("%s: ERROR: timer memory alloc failed \n", __func__);
+		return -ENOMEM;
+	}
+	priv->tm->freq = tmrate;
+
+	/* Test if the HW timer can be actually used.
+	 * In case of failure continue with no timer. */
+	if (unlikely((stmmac_open_ext_timer(dev, priv->tm)) < 0)) {
+		pr_warning("stmmaceth: cannot attach the HW timer\n");
+		tmrate = 0;
+		priv->tm->freq = 0;
+		priv->tm->timer_start = stmmac_no_timer_started;
+		priv->tm->timer_stop = stmmac_no_timer_stopped;
+	}
+#endif
+
+	/* Create and initialize the TX/RX descriptors chains. */
+	priv->dma_tx_size = STMMAC_ALIGN(dma_txsize);
+	priv->dma_rx_size = STMMAC_ALIGN(dma_rxsize);
+	priv->dma_buf_sz = STMMAC_ALIGN(buf_sz);
+	init_dma_desc_rings(dev);
+
+	/* DMA initialization and SW reset */
+	if (unlikely(priv->mac_type->ops->dma_init(ioaddr,
+		priv->pbl, priv->dma_tx_phy, priv->dma_rx_phy) < 0)) {
+
+		pr_err("%s: DMA initialization failed\n", __func__);
+		return -1;
+	}
+
+	/* Copy the MAC addr into the HW  */
+	priv->mac_type->ops->set_umac_addr(ioaddr, dev->dev_addr, 0);
+	/* Initialize the MAC Core */
+	priv->mac_type->ops->core_init(ioaddr);
+
+	priv->shutdown = 0;
+
+	/* Initialise the MMC (if present) to disable all interrupts. */
+	writel(0xffffffff, ioaddr + MMC_HIGH_INTR_MASK);
+	writel(0xffffffff, ioaddr + MMC_LOW_INTR_MASK);
+
+	/* Enable the MAC Rx/Tx */
+	stmmac_mac_enable_rx(ioaddr);
+	stmmac_mac_enable_tx(ioaddr);
+
+	/* Set the HW DMA mode and the COE */
+	stmmac_dma_operation_mode(priv);
+
+	/* Extra statistics */
+	memset(&priv->xstats, 0, sizeof(struct stmmac_extra_stats));
+	priv->xstats.threshold = tc;
+
+	/* Start the ball rolling... */
+	DBG(probe, DEBUG, "%s: DMA RX/TX processes started...\n", dev->name);
+	stmmac_dma_start_tx(ioaddr);
+	stmmac_dma_start_rx(ioaddr);
+
+#ifdef CONFIG_STMMAC_TIMER
+	priv->tm->timer_start(tmrate);
+#endif
+	/* Dump DMA/MAC registers */
+	if (netif_msg_hw(priv)) {
+		priv->mac_type->ops->dump_mac_regs(ioaddr);
+		priv->mac_type->ops->dump_dma_regs(ioaddr);
+	}
+
+	if (priv->phydev)
+		phy_start(priv->phydev);
+
+	napi_enable(&priv->napi);
+	skb_queue_head_init(&priv->rx_recycle);
+	netif_start_queue(dev);
+	return 0;
+}
+
+/**
+ *  stmmac_release - close entry point of the driver
+ *  @dev : device pointer.
+ *  Description:
+ *  This is the stop entry point of the driver.
+ */
+static int stmmac_release(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	/* Stop and disconnect the PHY */
+	if (priv->phydev) {
+		phy_stop(priv->phydev);
+		phy_disconnect(priv->phydev);
+		priv->phydev = NULL;
+	}
+
+	netif_stop_queue(dev);
+
+#ifdef CONFIG_STMMAC_TIMER
+	/* Stop and release the timer */
+	stmmac_close_ext_timer();
+	if (priv->tm != NULL)
+		kfree(priv->tm);
+#endif
+	napi_disable(&priv->napi);
+	skb_queue_purge(&priv->rx_recycle);
+
+	/* Free the IRQ lines */
+	free_irq(dev->irq, dev);
+
+	/* Stop TX/RX DMA and clear the descriptors */
+	stmmac_dma_stop_tx(dev->base_addr);
+	stmmac_dma_stop_rx(dev->base_addr);
+
+	/* Release and free the Rx/Tx resources */
+	free_dma_desc_resources(priv);
+
+	/* Disable the MAC core */
+	stmmac_mac_disable_tx(dev->base_addr);
+	stmmac_mac_disable_rx(dev->base_addr);
+
+	netif_carrier_off(dev);
+
+	return 0;
+}
+
+/*
+ * To perform emulated hardware segmentation on skb.
+ */
+static int stmmac_sw_tso(struct stmmac_priv *priv, struct sk_buff *skb)
+{
+	struct sk_buff *segs, *curr_skb;
+	int gso_segs = skb_shinfo(skb)->gso_segs;
+
+	/* Estimate the number of fragments in the worst case */
+	if (unlikely(stmmac_tx_avail(priv) < gso_segs)) {
+		netif_stop_queue(priv->dev);
+		TX_DBG(KERN_ERR "%s: TSO BUG! Tx Ring full when queue awake\n",
+		       __func__);
+		if (stmmac_tx_avail(priv) < gso_segs)
+			return NETDEV_TX_BUSY;
+
+		netif_wake_queue(priv->dev);
+	}
+	TX_DBG("\tstmmac_sw_tso: segmenting: skb %p (len %d)\n",
+	       skb, skb->len);
+
+	segs = skb_gso_segment(skb, priv->dev->features & ~NETIF_F_TSO);
+	if (unlikely(IS_ERR(segs)))
+		goto sw_tso_end;
+
+	do {
+		curr_skb = segs;
+		segs = segs->next;
+		TX_DBG("\t\tcurrent skb->len: %d, *curr %p,"
+		       "*next %p\n", curr_skb->len, curr_skb, segs);
+		curr_skb->next = NULL;
+		stmmac_xmit(curr_skb, priv->dev);
+	} while (segs);
+
+sw_tso_end:
+	dev_kfree_skb(skb);
+
+	return NETDEV_TX_OK;
+}
+
+static unsigned int stmmac_handle_jumbo_frames(struct sk_buff *skb,
+					       struct net_device *dev,
+					       int csum_insertion)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	unsigned int nopaged_len = skb_headlen(skb);
+	unsigned int txsize = priv->dma_tx_size;
+	unsigned int entry = priv->cur_tx % txsize;
+	struct dma_desc *desc = priv->dma_tx + entry;
+
+	if (nopaged_len > BUF_SIZE_8KiB) {
+
+		int buf2_size = nopaged_len - BUF_SIZE_8KiB;
+
+		desc->des2 = dma_map_single(priv->device, skb->data,
+					    BUF_SIZE_8KiB, DMA_TO_DEVICE);
+		desc->des3 = desc->des2 + BUF_SIZE_4KiB;
+		priv->mac_type->ops->prepare_tx_desc(desc, 1, BUF_SIZE_8KiB,
+						     csum_insertion);
+
+		entry = (++priv->cur_tx) % txsize;
+		desc = priv->dma_tx + entry;
+
+		desc->des2 = dma_map_single(priv->device,
+					skb->data + BUF_SIZE_8KiB,
+					buf2_size, DMA_TO_DEVICE);
+		desc->des3 = desc->des2 + BUF_SIZE_4KiB;
+		priv->mac_type->ops->prepare_tx_desc(desc, 0,
+						     buf2_size, csum_insertion);
+		priv->mac_type->ops->set_tx_owner(desc);
+		priv->tx_skbuff[entry] = NULL;
+	} else {
+		desc->des2 = dma_map_single(priv->device, skb->data,
+					nopaged_len, DMA_TO_DEVICE);
+		desc->des3 = desc->des2 + BUF_SIZE_4KiB;
+		priv->mac_type->ops->prepare_tx_desc(desc, 1, nopaged_len,
+						     csum_insertion);
+	}
+	return entry;
+}
+
+/**
+ *  stmmac_xmit:
+ *  @skb : the socket buffer
+ *  @dev : device pointer
+ *  Description : Tx entry point of the driver.
+ */
+static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	unsigned int txsize = priv->dma_tx_size;
+	unsigned int entry;
+	int i, csum_insertion = 0;
+	int nfrags = skb_shinfo(skb)->nr_frags;
+	struct dma_desc *desc, *first;
+
+	if (unlikely(stmmac_tx_avail(priv) < nfrags + 1)) {
+		if (!netif_queue_stopped(dev)) {
+			netif_stop_queue(dev);
+			/* This is a hard error, log it. */
+			pr_err("%s: BUG! Tx Ring full when queue awake\n",
+				__func__);
+		}
+		return NETDEV_TX_BUSY;
+	}
+
+	entry = priv->cur_tx % txsize;
+
+#ifdef STMMAC_XMIT_DEBUG
+	if ((skb->len > ETH_FRAME_LEN) || nfrags)
+		pr_info("stmmac xmit:\n"
+		       "\tskb addr %p - len: %d - nopaged_len: %d\n"
+		       "\tn_frags: %d - ip_summed: %d - %s gso\n",
+		       skb, skb->len, skb_headlen(skb), nfrags, skb->ip_summed,
+		       !skb_is_gso(skb) ? "isn't" : "is");
+#endif
+
+	if (unlikely(skb_is_gso(skb)))
+		return stmmac_sw_tso(priv, skb);
+
+	if (likely((skb->ip_summed == CHECKSUM_PARTIAL))) {
+		if (likely(priv->tx_coe == NO_HW_CSUM))
+			skb_checksum_help(skb);
+		else
+			csum_insertion = 1;
+	}
+
+	desc = priv->dma_tx + entry;
+	first = desc;
+
+#ifdef STMMAC_XMIT_DEBUG
+	if ((nfrags > 0) || (skb->len > ETH_FRAME_LEN))
+		pr_debug("stmmac xmit: skb len: %d, nopaged_len: %d,\n"
+		       "\t\tn_frags: %d, ip_summed: %d\n",
+		       skb->len, skb_headlen(skb), nfrags, skb->ip_summed);
+#endif
+	priv->tx_skbuff[entry] = skb;
+	if (unlikely(skb->len >= BUF_SIZE_4KiB)) {
+		entry = stmmac_handle_jumbo_frames(skb, dev, csum_insertion);
+		desc = priv->dma_tx + entry;
+	} else {
+		unsigned int nopaged_len = skb_headlen(skb);
+		desc->des2 = dma_map_single(priv->device, skb->data,
+					nopaged_len, DMA_TO_DEVICE);
+		priv->mac_type->ops->prepare_tx_desc(desc, 1, nopaged_len,
+						     csum_insertion);
+	}
+
+	for (i = 0; i < nfrags; i++) {
+		skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+		int len = frag->size;
+
+		entry = (++priv->cur_tx) % txsize;
+		desc = priv->dma_tx + entry;
+
+		TX_DBG("\t[entry %d] segment len: %d\n", entry, len);
+		desc->des2 = dma_map_page(priv->device, frag->page,
+					  frag->page_offset,
+					  len, DMA_TO_DEVICE);
+		priv->tx_skbuff[entry] = NULL;
+		priv->mac_type->ops->prepare_tx_desc(desc, 0, len,
+						     csum_insertion);
+		priv->mac_type->ops->set_tx_owner(desc);
+	}
+
+	/* Interrupt on completition only for the latest segment */
+	priv->mac_type->ops->close_tx_desc(desc);
+#ifdef CONFIG_STMMAC_TIMER
+	/* Clean IC while using timers */
+	priv->mac_type->ops->clear_tx_ic(desc);
+#endif
+	/* To avoid raise condition */
+	priv->mac_type->ops->set_tx_owner(first);
+
+	priv->cur_tx++;
+
+#ifdef STMMAC_XMIT_DEBUG
+	if (netif_msg_pktdata(priv)) {
+		pr_info("stmmac xmit: current=%d, dirty=%d, entry=%d, "
+		       "first=%p, nfrags=%d\n",
+		       (priv->cur_tx % txsize), (priv->dirty_tx % txsize),
+		       entry, first, nfrags);
+		display_ring(priv->dma_tx, txsize);
+		pr_info(">>> frame to be transmitted: ");
+		print_pkt(skb->data, skb->len);
+	}
+#endif
+	if (unlikely(stmmac_tx_avail(priv) <= (MAX_SKB_FRAGS + 1))) {
+		TX_DBG("%s: stop transmitted packets\n", __func__);
+		netif_stop_queue(dev);
+	}
+
+	dev->stats.tx_bytes += skb->len;
+
+	/* CSR1 enables the transmit DMA to check for new descriptor */
+	writel(1, dev->base_addr + DMA_XMT_POLL_DEMAND);
+
+	return NETDEV_TX_OK;
+}
+
+static inline void stmmac_rx_refill(struct stmmac_priv *priv)
+{
+	unsigned int rxsize = priv->dma_rx_size;
+	int bfsize = priv->dma_buf_sz;
+	struct dma_desc *p = priv->dma_rx;
+
+	for (; priv->cur_rx - priv->dirty_rx > 0; priv->dirty_rx++) {
+		unsigned int entry = priv->dirty_rx % rxsize;
+		if (likely(priv->rx_skbuff[entry] == NULL)) {
+			struct sk_buff *skb;
+
+			skb = __skb_dequeue(&priv->rx_recycle);
+			if (skb == NULL)
+				skb = netdev_alloc_skb_ip_align(priv->dev,
+								bfsize);
+
+			if (unlikely(skb == NULL))
+				break;
+
+			priv->rx_skbuff[entry] = skb;
+			priv->rx_skbuff_dma[entry] =
+			    dma_map_single(priv->device, skb->data, bfsize,
+					   DMA_FROM_DEVICE);
+
+			(p + entry)->des2 = priv->rx_skbuff_dma[entry];
+			if (unlikely(priv->is_gmac)) {
+				if (bfsize >= BUF_SIZE_8KiB)
+					(p + entry)->des3 =
+					    (p + entry)->des2 + BUF_SIZE_8KiB;
+			}
+			RX_DBG(KERN_INFO "\trefill entry #%d\n", entry);
+		}
+		priv->mac_type->ops->set_rx_owner(p + entry);
+	}
+	return;
+}
+
+static int stmmac_rx(struct stmmac_priv *priv, int limit)
+{
+	unsigned int rxsize = priv->dma_rx_size;
+	unsigned int entry = priv->cur_rx % rxsize;
+	unsigned int next_entry;
+	unsigned int count = 0;
+	struct dma_desc *p = priv->dma_rx + entry;
+	struct dma_desc *p_next;
+
+#ifdef STMMAC_RX_DEBUG
+	if (netif_msg_hw(priv)) {
+		pr_debug(">>> stmmac_rx: descriptor ring:\n");
+		display_ring(priv->dma_rx, rxsize);
+	}
+#endif
+	count = 0;
+	while (!priv->mac_type->ops->get_rx_owner(p)) {
+		int status;
+
+		if (count >= limit)
+			break;
+
+		count++;
+
+		next_entry = (++priv->cur_rx) % rxsize;
+		p_next = priv->dma_rx + next_entry;
+		prefetch(p_next);
+
+		/* read the status of the incoming frame */
+		status = (priv->mac_type->ops->rx_status(&priv->dev->stats,
+							 &priv->xstats, p));
+		if (unlikely(status == discard_frame))
+			priv->dev->stats.rx_errors++;
+		else {
+			struct sk_buff *skb;
+			/* Length should omit the CRC */
+			int frame_len =
+			    priv->mac_type->ops->get_rx_frame_len(p) - 4;
+
+#ifdef STMMAC_RX_DEBUG
+			if (frame_len > ETH_FRAME_LEN)
+				pr_debug("\tRX frame size %d, COE status: %d\n",
+					frame_len, status);
+
+			if (netif_msg_hw(priv))
+				pr_debug("\tdesc: %p [entry %d] buff=0x%x\n",
+					p, entry, p->des2);
+#endif
+			skb = priv->rx_skbuff[entry];
+			if (unlikely(!skb)) {
+				pr_err("%s: Inconsistent Rx descriptor chain\n",
+					priv->dev->name);
+				priv->dev->stats.rx_dropped++;
+				break;
+			}
+			prefetch(skb->data - NET_IP_ALIGN);
+			priv->rx_skbuff[entry] = NULL;
+
+			skb_put(skb, frame_len);
+			dma_unmap_single(priv->device,
+					 priv->rx_skbuff_dma[entry],
+					 priv->dma_buf_sz, DMA_FROM_DEVICE);
+#ifdef STMMAC_RX_DEBUG
+			if (netif_msg_pktdata(priv)) {
+				pr_info(" frame received (%dbytes)", frame_len);
+				print_pkt(skb->data, frame_len);
+			}
+#endif
+			skb->protocol = eth_type_trans(skb, priv->dev);
+
+			if (unlikely(status == csum_none)) {
+				/* always for the old mac 10/100 */
+				skb->ip_summed = CHECKSUM_NONE;
+				netif_receive_skb(skb);
+			} else {
+				skb->ip_summed = CHECKSUM_UNNECESSARY;
+				napi_gro_receive(&priv->napi, skb);
+			}
+
+			priv->dev->stats.rx_packets++;
+			priv->dev->stats.rx_bytes += frame_len;
+			priv->dev->last_rx = jiffies;
+		}
+		entry = next_entry;
+		p = p_next;	/* use prefetched values */
+	}
+
+	stmmac_rx_refill(priv);
+
+	priv->xstats.rx_pkt_n += count;
+
+	return count;
+}
+
+/**
+ *  stmmac_poll - stmmac poll method (NAPI)
+ *  @napi : pointer to the napi structure.
+ *  @budget : maximum number of packets that the current CPU can receive from
+ *	      all interfaces.
+ *  Description :
+ *   This function implements the the reception process.
+ *   Also it runs the TX completion thread
+ */
+static int stmmac_poll(struct napi_struct *napi, int budget)
+{
+	struct stmmac_priv *priv = container_of(napi, struct stmmac_priv, napi);
+	int work_done = 0;
+
+	priv->xstats.poll_n++;
+	stmmac_tx(priv);
+	work_done = stmmac_rx(priv, budget);
+
+	if (work_done < budget) {
+		napi_complete(napi);
+		stmmac_enable_irq(priv);
+	}
+	return work_done;
+}
+
+/**
+ *  stmmac_tx_timeout
+ *  @dev : Pointer to net device structure
+ *  Description: this function is called when a packet transmission fails to
+ *   complete within a reasonable tmrate. The driver will mark the error in the
+ *   netdev structure and arrange for the device to be reset to a sane state
+ *   in order to transmit a new packet.
+ */
+static void stmmac_tx_timeout(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	/* Clear Tx resources and restart transmitting again */
+	stmmac_tx_err(priv);
+	return;
+}
+
+/* Configuration changes (passed on by ifconfig) */
+static int stmmac_config(struct net_device *dev, struct ifmap *map)
+{
+	if (dev->flags & IFF_UP)	/* can't act on a running interface */
+		return -EBUSY;
+
+	/* Don't allow changing the I/O address */
+	if (map->base_addr != dev->base_addr) {
+		pr_warning("%s: can't change I/O address\n", dev->name);
+		return -EOPNOTSUPP;
+	}
+
+	/* Don't allow changing the IRQ */
+	if (map->irq != dev->irq) {
+		pr_warning("%s: can't change IRQ number %d\n",
+		       dev->name, dev->irq);
+		return -EOPNOTSUPP;
+	}
+
+	/* ignore other fields */
+	return 0;
+}
+
+/**
+ *  stmmac_multicast_list - entry point for multicast addressing
+ *  @dev : pointer to the device structure
+ *  Description:
+ *  This function is a driver entry point which gets called by the kernel
+ *  whenever multicast addresses must be enabled/disabled.
+ *  Return value:
+ *  void.
+ */
+static void stmmac_multicast_list(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	spin_lock(&priv->lock);
+	priv->mac_type->ops->set_filter(dev);
+	spin_unlock(&priv->lock);
+	return;
+}
+
+/**
+ *  stmmac_change_mtu - entry point to change MTU size for the device.
+ *  @dev : device pointer.
+ *  @new_mtu : the new MTU size for the device.
+ *  Description: the Maximum Transfer Unit (MTU) is used by the network layer
+ *  to drive packet transmission. Ethernet has an MTU of 1500 octets
+ *  (ETH_DATA_LEN). This value can be changed with ifconfig.
+ *  Return value:
+ *  0 on success and an appropriate (-)ve integer as defined in errno.h
+ *  file on failure.
+ */
+static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	int max_mtu;
+
+	if (netif_running(dev)) {
+		pr_err("%s: must be stopped to change its MTU\n", dev->name);
+		return -EBUSY;
+	}
+
+	if (priv->is_gmac)
+		max_mtu = JUMBO_LEN;
+	else
+		max_mtu = ETH_DATA_LEN;
+
+	if ((new_mtu < 46) || (new_mtu > max_mtu)) {
+		pr_err("%s: invalid MTU, max MTU is: %d\n", dev->name, max_mtu);
+		return -EINVAL;
+	}
+
+	dev->mtu = new_mtu;
+
+	return 0;
+}
+
+static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
+{
+	struct net_device *dev = (struct net_device *)dev_id;
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	if (unlikely(!dev)) {
+		pr_err("%s: invalid dev pointer\n", __func__);
+		return IRQ_NONE;
+	}
+
+	if (priv->is_gmac) {
+		unsigned long ioaddr = dev->base_addr;
+		/* To handle GMAC own interrupts */
+		priv->mac_type->ops->host_irq_status(ioaddr);
+	}
+	stmmac_dma_interrupt(dev);
+
+	return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+/* Polling receive - used by NETCONSOLE and other diagnostic tools
+ * to allow network I/O with interrupts disabled. */
+static void stmmac_poll_controller(struct net_device *dev)
+{
+	disable_irq(dev->irq);
+	stmmac_interrupt(dev->irq, dev);
+	enable_irq(dev->irq);
+}
+#endif
+
+/**
+ *  stmmac_ioctl - Entry point for the Ioctl
+ *  @dev: Device pointer.
+ *  @rq: An IOCTL specefic structure, that can contain a pointer to
+ *  a proprietary structure used to pass information to the driver.
+ *  @cmd: IOCTL command
+ *  Description:
+ *  Currently there are no special functionality supported in IOCTL, just the
+ *  phy_mii_ioctl(...) can be invoked.
+ */
+static int stmmac_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	int ret = -EOPNOTSUPP;
+
+	if (!netif_running(dev))
+		return -EINVAL;
+
+	switch (cmd) {
+	case SIOCGMIIPHY:
+	case SIOCGMIIREG:
+	case SIOCSMIIREG:
+		if (!priv->phydev)
+			return -EINVAL;
+
+		spin_lock(&priv->lock);
+		ret = phy_mii_ioctl(priv->phydev, if_mii(rq), cmd);
+		spin_unlock(&priv->lock);
+	default:
+		break;
+	}
+	return ret;
+}
+
+#ifdef STMMAC_VLAN_TAG_USED
+static void stmmac_vlan_rx_register(struct net_device *dev,
+				    struct vlan_group *grp)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	DBG(probe, INFO, "%s: Setting vlgrp to %p\n", dev->name, grp);
+
+	spin_lock(&priv->lock);
+	priv->vlgrp = grp;
+	spin_unlock(&priv->lock);
+
+	return;
+}
+#endif
+
+static const struct net_device_ops stmmac_netdev_ops = {
+	.ndo_open = stmmac_open,
+	.ndo_start_xmit = stmmac_xmit,
+	.ndo_stop = stmmac_release,
+	.ndo_change_mtu = stmmac_change_mtu,
+	.ndo_set_multicast_list = stmmac_multicast_list,
+	.ndo_tx_timeout = stmmac_tx_timeout,
+	.ndo_do_ioctl = stmmac_ioctl,
+	.ndo_set_config = stmmac_config,
+#ifdef STMMAC_VLAN_TAG_USED
+	.ndo_vlan_rx_register = stmmac_vlan_rx_register,
+#endif
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	.ndo_poll_controller = stmmac_poll_controller,
+#endif
+	.ndo_set_mac_address = eth_mac_addr,
+};
+
+/**
+ * stmmac_probe - Initialization of the adapter .
+ * @dev : device pointer
+ * Description: The function initializes the network device structure for
+ * the STMMAC driver. It also calls the low level routines
+ * in order to init the HW (i.e. the DMA engine)
+ */
+static int stmmac_probe(struct net_device *dev)
+{
+	int ret = 0;
+	struct stmmac_priv *priv = netdev_priv(dev);
+
+	ether_setup(dev);
+
+	dev->netdev_ops = &stmmac_netdev_ops;
+	stmmac_set_ethtool_ops(dev);
+
+	dev->features |= (NETIF_F_SG | NETIF_F_HW_CSUM | NETIF_F_HIGHDMA);
+	dev->watchdog_timeo = msecs_to_jiffies(watchdog);
+#ifdef STMMAC_VLAN_TAG_USED
+	/* Both mac100 and gmac support receive VLAN tag detection */
+	dev->features |= NETIF_F_HW_VLAN_RX;
+#endif
+	priv->msg_enable = netif_msg_init(debug, default_msg_level);
+
+	if (priv->is_gmac)
+		priv->rx_csum = 1;
+
+	if (flow_ctrl)
+		priv->flow_ctrl = FLOW_AUTO;	/* RX/TX pause on */
+
+	priv->pause = pause;
+	netif_napi_add(dev, &priv->napi, stmmac_poll, 64);
+
+	/* Get the MAC address */
+	priv->mac_type->ops->get_umac_addr(dev->base_addr, dev->dev_addr, 0);
+
+	if (!is_valid_ether_addr(dev->dev_addr))
+		pr_warning("\tno valid MAC address;"
+			"please, use ifconfig or nwhwconfig!\n");
+
+	ret = register_netdev(dev);
+	if (ret) {
+		pr_err("%s: ERROR %i registering the device\n",
+		       __func__, ret);
+		return -ENODEV;
+	}
+
+	DBG(probe, DEBUG, "%s: Scatter/Gather: %s - HW checksums: %s\n",
+	    dev->name, (dev->features & NETIF_F_SG) ? "on" : "off",
+	    (dev->features & NETIF_F_HW_CSUM) ? "on" : "off");
+
+	spin_lock_init(&priv->lock);
+
+	return ret;
+}
+
+/**
+ * stmmac_mac_device_setup
+ * @dev : device pointer
+ * Description: select and initialise the mac device (mac100 or Gmac).
+ */
+static int stmmac_mac_device_setup(struct net_device *dev)
+{
+	struct stmmac_priv *priv = netdev_priv(dev);
+	unsigned long ioaddr = dev->base_addr;
+
+	struct mac_device_info *device;
+
+	if (priv->is_gmac)
+		device = gmac_setup(ioaddr);
+	else
+		device = mac100_setup(ioaddr);
+
+	if (!device)
+		return -ENOMEM;
+
+	priv->mac_type = device;
+
+	priv->wolenabled = priv->mac_type->hw.pmt;	/* PMT supported */
+	if (priv->wolenabled == PMT_SUPPORTED)
+		priv->wolopts = WAKE_MAGIC;		/* Magic Frame */
+
+	return 0;
+}
+
+static int stmmacphy_dvr_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacphy_data *plat_dat;
+	plat_dat = (struct plat_stmmacphy_data *)((pdev->dev).platform_data);
+
+	pr_debug("stmmacphy_dvr_probe: added phy for bus %d\n",
+	       plat_dat->bus_id);
+
+	return 0;
+}
+
+static int stmmacphy_dvr_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver stmmacphy_driver = {
+	.driver = {
+		   .name = PHY_RESOURCE_NAME,
+		   },
+	.probe = stmmacphy_dvr_probe,
+	.remove = stmmacphy_dvr_remove,
+};
+
+/**
+ * stmmac_associate_phy
+ * @dev: pointer to device structure
+ * @data: points to the private structure.
+ * Description: Scans through all the PHYs we have registered and checks if
+ * any are associated with our MAC.  If so, then just fill in
+ * the blanks in our local context structure
+ */
+static int stmmac_associate_phy(struct device *dev, void *data)
+{
+	struct stmmac_priv *priv = (struct stmmac_priv *)data;
+	struct plat_stmmacphy_data *plat_dat;
+
+	plat_dat = (struct plat_stmmacphy_data *)(dev->platform_data);
+
+	DBG(probe, DEBUG, "%s: checking phy for bus %d\n", __func__,
+		plat_dat->bus_id);
+
+	/* Check that this phy is for the MAC being initialised */
+	if (priv->bus_id != plat_dat->bus_id)
+		return 0;
+
+	/* OK, this PHY is connected to the MAC.
+	   Go ahead and get the parameters */
+	DBG(probe, DEBUG, "%s: OK. Found PHY config\n", __func__);
+	priv->phy_irq =
+	    platform_get_irq_byname(to_platform_device(dev), "phyirq");
+	DBG(probe, DEBUG, "%s: PHY irq on bus %d is %d\n", __func__,
+	    plat_dat->bus_id, priv->phy_irq);
+
+	/* Override with kernel parameters if supplied XXX CRS XXX
+	 * this needs to have multiple instances */
+	if ((phyaddr >= 0) && (phyaddr <= 31))
+		plat_dat->phy_addr = phyaddr;
+
+	priv->phy_addr = plat_dat->phy_addr;
+	priv->phy_mask = plat_dat->phy_mask;
+	priv->phy_interface = plat_dat->interface;
+	priv->phy_reset = plat_dat->phy_reset;
+
+	DBG(probe, DEBUG, "%s: exiting\n", __func__);
+	return 1;	/* forces exit of driver_for_each_device() */
+}
+
+/**
+ * stmmac_dvr_probe
+ * @pdev: platform device pointer
+ * Description: the driver is initialized through platform_device.
+ */
+static int stmmac_dvr_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct resource *res;
+	unsigned int *addr = NULL;
+	struct net_device *ndev = NULL;
+	struct stmmac_priv *priv;
+	struct plat_stmmacenet_data *plat_dat;
+
+	pr_info("STMMAC driver:\n\tplatform registration... ");
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		ret = -ENODEV;
+		goto out;
+	}
+	pr_info("done!\n");
+
+	if (!request_mem_region(res->start, (res->end - res->start),
+				pdev->name)) {
+		pr_err("%s: ERROR: memory allocation failed"
+		       "cannot get the I/O addr 0x%x\n",
+		       __func__, (unsigned int)res->start);
+		ret = -EBUSY;
+		goto out;
+	}
+
+	addr = ioremap(res->start, (res->end - res->start));
+	if (!addr) {
+		pr_err("%s: ERROR: memory mapping failed \n", __func__);
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	ndev = alloc_etherdev(sizeof(struct stmmac_priv));
+	if (!ndev) {
+		pr_err("%s: ERROR: allocating the device\n", __func__);
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+
+	/* Get the MAC information */
+	ndev->irq = platform_get_irq_byname(pdev, "macirq");
+	if (ndev->irq == -ENXIO) {
+		pr_err("%s: ERROR: MAC IRQ configuration "
+		       "information not found\n", __func__);
+		ret = -ENODEV;
+		goto out;
+	}
+
+	priv = netdev_priv(ndev);
+	priv->device = &(pdev->dev);
+	priv->dev = ndev;
+	plat_dat = (struct plat_stmmacenet_data *)((pdev->dev).platform_data);
+	priv->bus_id = plat_dat->bus_id;
+	priv->pbl = plat_dat->pbl;	/* TLI */
+	priv->is_gmac = plat_dat->has_gmac;	/* GMAC is on board */
+
+	platform_set_drvdata(pdev, ndev);
+
+	/* Set the I/O base addr */
+	ndev->base_addr = (unsigned long)addr;
+
+	/* MAC HW revice detection */
+	ret = stmmac_mac_device_setup(ndev);
+	if (ret < 0)
+		goto out;
+
+	/* Network Device Registration */
+	ret = stmmac_probe(ndev);
+	if (ret < 0)
+		goto out;
+
+	/* associate a PHY - it is provided by another platform bus */
+	if (!driver_for_each_device
+	    (&(stmmacphy_driver.driver), NULL, (void *)priv,
+	     stmmac_associate_phy)) {
+		pr_err("No PHY device is associated with this MAC!\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	priv->fix_mac_speed = plat_dat->fix_mac_speed;
+	priv->bsp_priv = plat_dat->bsp_priv;
+
+	pr_info("\t%s - (dev. name: %s - id: %d, IRQ #%d\n"
+	       "\tIO base addr: 0x%08x)\n", ndev->name, pdev->name,
+	       pdev->id, ndev->irq, (unsigned int)addr);
+
+	/* MDIO bus Registration */
+	pr_debug("\tMDIO bus (id: %d)...", priv->bus_id);
+	ret = stmmac_mdio_register(ndev);
+	if (ret < 0)
+		goto out;
+	pr_debug("registered!\n");
+
+out:
+	if (ret < 0) {
+		platform_set_drvdata(pdev, NULL);
+		release_mem_region(res->start, (res->end - res->start));
+		if (addr != NULL)
+			iounmap(addr);
+	}
+
+	return ret;
+}
+
+/**
+ * stmmac_dvr_remove
+ * @pdev: platform device pointer
+ * Description: this function resets the TX/RX processes, disables the MAC RX/TX
+ * changes the link status, releases the DMA descriptor rings,
+ * unregisters the MDIO bus and unmaps the allocated memory.
+ */
+static int stmmac_dvr_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+	struct resource *res;
+
+	pr_info("%s:\n\tremoving driver", __func__);
+
+	stmmac_dma_stop_rx(ndev->base_addr);
+	stmmac_dma_stop_tx(ndev->base_addr);
+
+	stmmac_mac_disable_rx(ndev->base_addr);
+	stmmac_mac_disable_tx(ndev->base_addr);
+
+	netif_carrier_off(ndev);
+
+	stmmac_mdio_unregister(ndev);
+
+	platform_set_drvdata(pdev, NULL);
+	unregister_netdev(ndev);
+
+	iounmap((void *)ndev->base_addr);
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(res->start, (res->end - res->start));
+
+	free_netdev(ndev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int stmmac_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	struct net_device *dev = platform_get_drvdata(pdev);
+	struct stmmac_priv *priv = netdev_priv(dev);
+	int dis_ic = 0;
+
+	if (!dev || !netif_running(dev))
+		return 0;
+
+	spin_lock(&priv->lock);
+
+	if (state.event == PM_EVENT_SUSPEND) {
+		netif_device_detach(dev);
+		netif_stop_queue(dev);
+		if (priv->phydev)
+			phy_stop(priv->phydev);
+
+#ifdef CONFIG_STMMAC_TIMER
+		priv->tm->timer_stop();
+		dis_ic = 1;
+#endif
+		napi_disable(&priv->napi);
+
+		/* Stop TX/RX DMA */
+		stmmac_dma_stop_tx(dev->base_addr);
+		stmmac_dma_stop_rx(dev->base_addr);
+		/* Clear the Rx/Tx descriptors */
+		priv->mac_type->ops->init_rx_desc(priv->dma_rx,
+						  priv->dma_rx_size, dis_ic);
+		priv->mac_type->ops->init_tx_desc(priv->dma_tx,
+						  priv->dma_tx_size);
+
+		stmmac_mac_disable_tx(dev->base_addr);
+
+		if (device_may_wakeup(&(pdev->dev))) {
+			/* Enable Power down mode by programming the PMT regs */
+			if (priv->wolenabled == PMT_SUPPORTED)
+				priv->mac_type->ops->pmt(dev->base_addr,
+							 priv->wolopts);
+		} else {
+			stmmac_mac_disable_rx(dev->base_addr);
+		}
+	} else {
+		priv->shutdown = 1;
+		/* Although this can appear slightly redundant it actually
+		 * makes fast the standby operation and guarantees the driver
+		 * working if hibernation is on media. */
+		stmmac_release(dev);
+	}
+
+	spin_unlock(&priv->lock);
+	return 0;
+}
+
+static int stmmac_resume(struct platform_device *pdev)
+{
+	struct net_device *dev = platform_get_drvdata(pdev);
+	struct stmmac_priv *priv = netdev_priv(dev);
+	unsigned long ioaddr = dev->base_addr;
+
+	if (!netif_running(dev))
+		return 0;
+
+	spin_lock(&priv->lock);
+
+	if (priv->shutdown) {
+		/* Re-open the interface and re-init the MAC/DMA
+		   and the rings. */
+		stmmac_open(dev);
+		goto out_resume;
+	}
+
+	/* Power Down bit, into the PM register, is cleared
+	 * automatically as soon as a magic packet or a Wake-up frame
+	 * is received. Anyway, it's better to manually clear
+	 * this bit because it can generate problems while resuming
+	 * from another devices (e.g. serial console). */
+	if (device_may_wakeup(&(pdev->dev)))
+		if (priv->wolenabled == PMT_SUPPORTED)
+			priv->mac_type->ops->pmt(dev->base_addr, 0);
+
+	netif_device_attach(dev);
+
+	/* Enable the MAC and DMA */
+	stmmac_mac_enable_rx(ioaddr);
+	stmmac_mac_enable_tx(ioaddr);
+	stmmac_dma_start_tx(ioaddr);
+	stmmac_dma_start_rx(ioaddr);
+
+#ifdef CONFIG_STMMAC_TIMER
+	priv->tm->timer_start(tmrate);
+#endif
+	napi_enable(&priv->napi);
+
+	if (priv->phydev)
+		phy_start(priv->phydev);
+
+	netif_start_queue(dev);
+
+out_resume:
+	spin_unlock(&priv->lock);
+	return 0;
+}
+#endif
+
+static struct platform_driver stmmac_driver = {
+	.driver = {
+		   .name = STMMAC_RESOURCE_NAME,
+		   },
+	.probe = stmmac_dvr_probe,
+	.remove = stmmac_dvr_remove,
+#ifdef CONFIG_PM
+	.suspend = stmmac_suspend,
+	.resume = stmmac_resume,
+#endif
+
+};
+
+/**
+ * stmmac_init_module - Entry point for the driver
+ * Description: This function is the entry point for the driver.
+ */
+static int __init stmmac_init_module(void)
+{
+	int ret;
+
+	if (platform_driver_register(&stmmacphy_driver)) {
+		pr_err("No PHY devices registered!\n");
+		return -ENODEV;
+	}
+
+	ret = platform_driver_register(&stmmac_driver);
+	return ret;
+}
+
+/**
+ * stmmac_cleanup_module - Cleanup routine for the driver
+ * Description: This function is the cleanup routine for the driver.
+ */
+static void __exit stmmac_cleanup_module(void)
+{
+	platform_driver_unregister(&stmmacphy_driver);
+	platform_driver_unregister(&stmmac_driver);
+}
+
+#ifndef MODULE
+static int __init stmmac_cmdline_opt(char *str)
+{
+	char *opt;
+
+	if (!str || !*str)
+		return -EINVAL;
+	while ((opt = strsep(&str, ",")) != NULL) {
+		if (!strncmp(opt, "debug:", 6))
+			strict_strtoul(opt + 6, 0, (unsigned long *)&debug);
+		else if (!strncmp(opt, "phyaddr:", 8))
+			strict_strtoul(opt + 8, 0, (unsigned long *)&phyaddr);
+		else if (!strncmp(opt, "dma_txsize:", 11))
+			strict_strtoul(opt + 11, 0,
+				       (unsigned long *)&dma_txsize);
+		else if (!strncmp(opt, "dma_rxsize:", 11))
+			strict_strtoul(opt + 11, 0,
+				       (unsigned long *)&dma_rxsize);
+		else if (!strncmp(opt, "buf_sz:", 7))
+			strict_strtoul(opt + 7, 0, (unsigned long *)&buf_sz);
+		else if (!strncmp(opt, "tc:", 3))
+			strict_strtoul(opt + 3, 0, (unsigned long *)&tc);
+		else if (!strncmp(opt, "tx_coe:", 7))
+			strict_strtoul(opt + 7, 0, (unsigned long *)&tx_coe);
+		else if (!strncmp(opt, "watchdog:", 9))
+			strict_strtoul(opt + 9, 0, (unsigned long *)&watchdog);
+		else if (!strncmp(opt, "flow_ctrl:", 10))
+			strict_strtoul(opt + 10, 0,
+				       (unsigned long *)&flow_ctrl);
+		else if (!strncmp(opt, "pause:", 6))
+			strict_strtoul(opt + 6, 0, (unsigned long *)&pause);
+#ifdef CONFIG_STMMAC_TIMER
+		else if (!strncmp(opt, "tmrate:", 7))
+			strict_strtoul(opt + 7, 0, (unsigned long *)&tmrate);
+#endif
+	}
+	return 0;
+}
+
+__setup("stmmaceth=", stmmac_cmdline_opt);
+#endif
+
+module_init(stmmac_init_module);
+module_exit(stmmac_cleanup_module);
+
+MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet driver");
+MODULE_AUTHOR("Giuseppe Cavallaro <[email-masked]>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/stmmac/stmmac_mdio.c b/drivers/net/stmmac/stmmac_mdio.c
new file mode 100644
index 0000000..8498552
--- /dev/null
+++ b/drivers/net/stmmac/stmmac_mdio.c
@@ -0,0 +1,217 @@
+/*******************************************************************************
+  STMMAC Ethernet Driver -- MDIO bus implementation
+  Provides Bus interface for MII registers
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Carl Shaw <[email-masked]>
+  Maintainer: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#include <linux/netdevice.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+
+#include "stmmac.h"
+
+#define MII_BUSY 0x00000001
+#define MII_WRITE 0x00000002
+
+/**
+ * stmmac_mdio_read
+ * @bus: points to the mii_bus structure
+ * @phyaddr: MII addr reg bits 15-11
+ * @phyreg: MII addr reg bits 10-6
+ * Description: it reads data from the MII register from within the phy device.
+ * For the 7111 GMAC, we must set the bit 0 in the MII address register while
+ * accessing the PHY registers.
+ * Fortunately, it seems this has no drawback for the 7109 MAC.
+ */
+static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
+{
+	struct net_device *ndev = bus->priv;
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	unsigned long ioaddr = ndev->base_addr;
+	unsigned int mii_address = priv->mac_type->hw.mii.addr;
+	unsigned int mii_data = priv->mac_type->hw.mii.data;
+
+	int data;
+	u16 regValue = (((phyaddr << 11) & (0x0000F800)) |
+			((phyreg << 6) & (0x000007C0)));
+	regValue |= MII_BUSY;	/* in case of GMAC */
+
+	do {} while (((readl(ioaddr + mii_address)) & MII_BUSY) == 1);
+	writel(regValue, ioaddr + mii_address);
+	do {} while (((readl(ioaddr + mii_address)) & MII_BUSY) == 1);
+
+	/* Read the data from the MII data register */
+	data = (int)readl(ioaddr + mii_data);
+
+	return data;
+}
+
+/**
+ * stmmac_mdio_write
+ * @bus: points to the mii_bus structure
+ * @phyaddr: MII addr reg bits 15-11
+ * @phyreg: MII addr reg bits 10-6
+ * @phydata: phy data
+ * Description: it writes the data into the MII register from within the device.
+ */
+static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg,
+			     u16 phydata)
+{
+	struct net_device *ndev = bus->priv;
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	unsigned long ioaddr = ndev->base_addr;
+	unsigned int mii_address = priv->mac_type->hw.mii.addr;
+	unsigned int mii_data = priv->mac_type->hw.mii.data;
+
+	u16 value =
+	    (((phyaddr << 11) & (0x0000F800)) | ((phyreg << 6) & (0x000007C0)))
+	    | MII_WRITE;
+
+	value |= MII_BUSY;
+
+	/* Wait until any existing MII operation is complete */
+	do {} while (((readl(ioaddr + mii_address)) & MII_BUSY) == 1);
+
+	/* Set the MII address register to write */
+	writel(phydata, ioaddr + mii_data);
+	writel(value, ioaddr + mii_address);
+
+	/* Wait until any existing MII operation is complete */
+	do {} while (((readl(ioaddr + mii_address)) & MII_BUSY) == 1);
+
+	return 0;
+}
+
+/**
+ * stmmac_mdio_reset
+ * @bus: points to the mii_bus structure
+ * Description: reset the MII bus
+ */
+static int stmmac_mdio_reset(struct mii_bus *bus)
+{
+	struct net_device *ndev = bus->priv;
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	unsigned long ioaddr = ndev->base_addr;
+	unsigned int mii_address = priv->mac_type->hw.mii.addr;
+
+	if (priv->phy_reset) {
+		pr_debug("stmmac_mdio_reset: calling phy_reset\n");
+		priv->phy_reset(priv->bsp_priv);
+	}
+
+	/* This is a workaround for problems with the STE101P PHY.
+	 * It doesn't complete its reset until at least one clock cycle
+	 * on MDC, so perform a dummy mdio read.
+	 */
+	writel(0, ioaddr + mii_address);
+
+	return 0;
+}
+
+/**
+ * stmmac_mdio_register
+ * @ndev: net device structure
+ * Description: it registers the MII bus
+ */
+int stmmac_mdio_register(struct net_device *ndev)
+{
+	int err = 0;
+	struct mii_bus *new_bus;
+	int *irqlist;
+	struct stmmac_priv *priv = netdev_priv(ndev);
+	int addr, found;
+
+	new_bus = mdiobus_alloc();
+	if (new_bus == NULL)
+		return -ENOMEM;
+
+	irqlist = kzalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+	if (irqlist == NULL) {
+		err = -ENOMEM;
+		goto irqlist_alloc_fail;
+	}
+
+	/* Assign IRQ to phy at address phy_addr */
+	if (priv->phy_addr != -1)
+		irqlist[priv->phy_addr] = priv->phy_irq;
+
+	new_bus->name = "STMMAC MII Bus";
+	new_bus->read = &stmmac_mdio_read;
+	new_bus->write = &stmmac_mdio_write;
+	new_bus->reset = &stmmac_mdio_reset;
+	snprintf(new_bus->id, MII_BUS_ID_SIZE, "%x", priv->bus_id);
+	new_bus->priv = ndev;
+	new_bus->irq = irqlist;
+	new_bus->phy_mask = priv->phy_mask;
+	new_bus->parent = priv->device;
+	err = mdiobus_register(new_bus);
+	if (err != 0) {
+		pr_err("%s: Cannot register as MDIO bus\n", new_bus->name);
+		goto bus_register_fail;
+	}
+
+	priv->mii = new_bus;
+
+	found = 0;
+	for (addr = 0; addr < 32; addr++) {
+		struct phy_device *phydev = new_bus->phy_map[addr];
+		if (phydev) {
+			if (priv->phy_addr == -1) {
+				priv->phy_addr = addr;
+				phydev->irq = priv->phy_irq;
+				irqlist[addr] = priv->phy_irq;
+			}
+			pr_info("%s: PHY ID %08x at %d IRQ %d (%s)%s\n",
+			       ndev->name, phydev->phy_id, addr,
+			       phydev->irq, dev_name(&phydev->dev),
+			       (addr == priv->phy_addr) ? " active" : "");
+			found = 1;
+		}
+	}
+
+	if (!found)
+		pr_warning("%s: No PHY found\n", ndev->name);
+
+	return 0;
+bus_register_fail:
+	kfree(irqlist);
+irqlist_alloc_fail:
+	kfree(new_bus);
+	return err;
+}
+
+/**
+ * stmmac_mdio_unregister
+ * @ndev: net device structure
+ * Description: it unregisters the MII bus
+ */
+int stmmac_mdio_unregister(struct net_device *ndev)
+{
+	struct stmmac_priv *priv = netdev_priv(ndev);
+
+	mdiobus_unregister(priv->mii);
+	priv->mii->priv = NULL;
+	kfree(priv->mii);
+
+	return 0;
+}
diff --git a/drivers/net/stmmac/stmmac_timer.c b/drivers/net/stmmac/stmmac_timer.c
new file mode 100644
index 0000000..b838c65
--- /dev/null
+++ b/drivers/net/stmmac/stmmac_timer.c
@@ -0,0 +1,140 @@
+/*******************************************************************************
+  STMMAC external timer support.
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+#include <linux/kernel.h>
+#include <linux/etherdevice.h>
+#include "stmmac_timer.h"
+
+static void stmmac_timer_handler(void *data)
+{
+	struct net_device *dev = (struct net_device *)data;
+
+	stmmac_schedule(dev);
+
+	return;
+}
+
+#define STMMAC_TIMER_MSG(timer, freq) \
+printk(KERN_INFO "stmmac_timer: %s Timer ON (freq %dHz)\n", timer, freq);
+
+#if defined(CONFIG_STMMAC_RTC_TIMER)
+#include <linux/rtc.h>
+static struct rtc_device *stmmac_rtc;
+static rtc_task_t stmmac_task;
+
+static void stmmac_rtc_start(unsigned int new_freq)
+{
+	rtc_irq_set_freq(stmmac_rtc, &stmmac_task, new_freq);
+	rtc_irq_set_state(stmmac_rtc, &stmmac_task, 1);
+	return;
+}
+
+static void stmmac_rtc_stop(void)
+{
+	rtc_irq_set_state(stmmac_rtc, &stmmac_task, 0);
+	return;
+}
+
+int stmmac_open_ext_timer(struct net_device *dev, struct stmmac_timer *tm)
+{
+	stmmac_task.private_data = dev;
+	stmmac_task.func = stmmac_timer_handler;
+
+	stmmac_rtc = rtc_class_open(CONFIG_RTC_HCTOSYS_DEVICE);
+	if (stmmac_rtc == NULL) {
+		pr_error("open rtc device failed\n");
+		return -ENODEV;
+	}
+
+	rtc_irq_register(stmmac_rtc, &stmmac_task);
+
+	/* Periodic mode is not supported */
+	if ((rtc_irq_set_freq(stmmac_rtc, &stmmac_task, tm->freq) < 0)) {
+		pr_error("set periodic failed\n");
+		rtc_irq_unregister(stmmac_rtc, &stmmac_task);
+		rtc_class_close(stmmac_rtc);
+		return -1;
+	}
+
+	STMMAC_TIMER_MSG(CONFIG_RTC_HCTOSYS_DEVICE, tm->freq);
+
+	tm->timer_start = stmmac_rtc_start;
+	tm->timer_stop = stmmac_rtc_stop;
+
+	return 0;
+}
+
+int stmmac_close_ext_timer(void)
+{
+	rtc_irq_set_state(stmmac_rtc, &stmmac_task, 0);
+	rtc_irq_unregister(stmmac_rtc, &stmmac_task);
+	rtc_class_close(stmmac_rtc);
+	return 0;
+}
+
+#elif defined(CONFIG_STMMAC_TMU_TIMER)
+#include <linux/clk.h>
+#define TMU_CHANNEL "tmu2_clk"
+static struct clk *timer_clock;
+
+static void stmmac_tmu_start(unsigned int new_freq)
+{
+	clk_set_rate(timer_clock, new_freq);
+	clk_enable(timer_clock);
+	return;
+}
+
+static void stmmac_tmu_stop(void)
+{
+	clk_disable(timer_clock);
+	return;
+}
+
+int stmmac_open_ext_timer(struct net_device *dev, struct stmmac_timer *tm)
+{
+	timer_clock = clk_get(NULL, TMU_CHANNEL);
+
+	if (timer_clock == NULL)
+		return -1;
+
+	if (tmu2_register_user(stmmac_timer_handler, (void *)dev) < 0) {
+		timer_clock = NULL;
+		return -1;
+	}
+
+	STMMAC_TIMER_MSG("TMU2", tm->freq);
+	tm->timer_start = stmmac_tmu_start;
+	tm->timer_stop = stmmac_tmu_stop;
+
+	return 0;
+}
+
+int stmmac_close_ext_timer(void)
+{
+	clk_disable(timer_clock);
+	tmu2_unregister_user();
+	clk_put(timer_clock);
+	return 0;
+}
+#endif
diff --git a/drivers/net/stmmac/stmmac_timer.h b/drivers/net/stmmac/stmmac_timer.h
new file mode 100644
index 0000000..f795cae
--- /dev/null
+++ b/drivers/net/stmmac/stmmac_timer.h
@@ -0,0 +1,41 @@
+/*******************************************************************************
+  STMMAC external timer Header File.
+
+  Copyright (C) 2007-2009  STMicroelectronics Ltd
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Author: Giuseppe Cavallaro <[email-masked]>
+*******************************************************************************/
+
+struct stmmac_timer {
+	void (*timer_start) (unsigned int new_freq);
+	void (*timer_stop) (void);
+	unsigned int freq;
+};
+
+/* Open the HW timer device and return 0 in case of success */
+int stmmac_open_ext_timer(struct net_device *dev, struct stmmac_timer *tm);
+/* Stop the timer and release it */
+int stmmac_close_ext_timer(void);
+/* Function used for scheduling task within the stmmac */
+void stmmac_schedule(struct net_device *dev);
+
+#if defined(CONFIG_STMMAC_TMU_TIMER)
+extern int tmu2_register_user(void *fnt, void *data);
+extern void tmu2_unregister_user(void);
+#endif
-- 
1.6.0.4