Subject: Re: [PATCH v3 net-next 3/3] arm64: dts: marvell: Add ethernet switch definition for the ESPRESSObin

From: Gregory CLEMENT <[email-masked]>
Date: Wed, 21 Dec 2016 10:41:09 +0100

Hi Romain,
 
 On mer., déc. 21 2016, Romain Perier <[email-masked]> wrote:

> This defines and enables the Marvell ethernet switch MVE886341 on the
> Marvell ESPRESSObin board.

This patch looks OK now.

Applied on mvebu/dt64-4.11

So you can remove it from you next version because I don't want this
patch will be applied through the netdev branch. Indeed I expect more
changes in this file for v4.11 and it will be easier to have the change
in a single branch to avoid the merge conflict.

Thanks,

Gregory

>
> Signed-off-by: Romain Perier <[email-masked]>
> ---
>
> Changes in v3:
>  - Changed the node switch0 to be at 1
>  - Removed reg=<1> from the mdio node, finally that's not required
>
> Changes in v2:
>  - EXPRESSObin -> ESPRESSObin
>  - phy nodes definition must contain the internal bus address after the @
>
>  .../boot/dts/marvell/armada-3720-espressobin.dts   | 66 ++++++++++++++++++++++
>  1 file changed, 66 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
> index 83178d9..12d9f65 100644
> --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
> @@ -80,3 +80,69 @@
>  &usb3 {
>  	status = "okay";
>  };
> +
> +&mdio {
> +	switch0: switch0@1 {
> +		compatible = "marvell,mv88e6085";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <1>;
> +
> +		dsa,member = <0 0>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				label = "cpu";
> +				ethernet = <&eth0>;
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				label = "wan";
> +				phy-handle = <&switch0phy0>;
> +			};
> +
> +			port@2 {
> +				reg = <2>;
> +				label = "lan0";
> +				phy-handle = <&switch0phy1>;
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				label = "lan1";
> +				phy-handle = <&switch0phy2>;
> +			};
> +
> +		};
> +
> +		mdio {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			switch0phy0: switch0phy0@11 {
> +				reg = <0x11>;
> +			};
> +			switch0phy1: switch0phy1@12 {
> +				reg = <0x12>;
> +			};
> +			switch0phy2: switch0phy2@13 {
> +				reg = <0x13>;
> +			};
> +		};
> +	};
> +};
> +
> +&eth0 {
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> -- 
> 2.9.3
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com