From: andrew@lunn•ch (Andrew Lunn)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH 0/9] ARM: Kirkwood: Convert to pinctrl
Date: Sun, 28 Oct 2012 21:01:39 +0100 [thread overview]
Message-ID: <20121028200139.GG15143@lunn.ch> (raw)
In-Reply-To: <20121028195018.GA16191@schnuecks.de>
On Sun, Oct 28, 2012 at 08:50:18PM +0100, Simon Baatz wrote:
> Hi Andrew,
>
> On Sun, Oct 28, 2012 at 05:57:11PM +0100, Andrew Lunn wrote:
> > On Wed, Oct 24, 2012 at 04:53:45PM +0200, Andrew Lunn wrote:
> > > This patchset converts all DT kirkwood boards to using pinctrl.
> >
> > I still expect problems with GPIOs used for power off. I've not yet
> > touched them. Again, a regulator makes sense, but there is no 'out of
> > the box' regulator type or property which adds itself to pm_power_off.
>
> the IB-NAS 62x0 works with the exception of the power off via GPIO.
> Additionally, the original U-Boot enables hardware blinking for the
> power led and Jamie's patch might be needed here as well. However, I
> don't use this U-Boot anymore and can't test this.
Hi Simon
Thanks for testing.
I hope Thomas Petazzoni will pickup the blinking patch and make sure
its O.K. for 370/XP. It can then be merged in.
power off via GPIO is next on my list of things to solve.
Andrew
next prev parent reply other threads:[~2012-10-28 20:01 UTC|newest]
Thread overview: 58+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-24 14:53 [PATCH 0/9] ARM: Kirkwood: Convert to pinctrl Andrew Lunn
2012-10-24 14:53 ` [PATCH 1/9] ARM: Kirkwood: Convert TS219 " Andrew Lunn
2012-10-24 19:31 ` Thomas Petazzoni
2012-10-24 19:49 ` Sebastian Hesselbarth
2012-10-24 20:00 ` Thomas Petazzoni
2012-10-24 20:04 ` Andrew Lunn
2012-10-24 20:05 ` Thomas Petazzoni
2012-10-24 20:14 ` Sebastian Hesselbarth
2012-10-24 20:19 ` Thomas Petazzoni
2012-10-24 14:53 ` [PATCH 2/9] ARM: Kirkwood: Convert iConnect " Andrew Lunn
2012-10-24 14:53 ` [PATCH 3/9] ARM: Kirkwood: Convert dnskw " Andrew Lunn
2012-10-25 22:58 ` Jamie Lentin
2012-10-26 6:01 ` Andrew Lunn
2012-10-26 9:42 ` Jamie Lentin
2012-10-26 10:24 ` Andrew Lunn
2012-10-26 12:30 ` Jamie Lentin
2012-10-24 14:53 ` [PATCH 4/9] ARM: Kirkwood: Convert dockstar " Andrew Lunn
2012-10-24 14:53 ` [PATCH 5/9] ARM: Kirkwood: Convert dreamplug " Andrew Lunn
2012-10-24 14:53 ` [PATCH 6/9] ARM: Kirkwood: Convert GoFlex Net " Andrew Lunn
2012-10-26 17:28 ` Josh Coombs
2012-10-27 8:51 ` Andrew Lunn
2012-10-28 14:31 ` Josh Coombs
2012-10-24 14:53 ` [PATCH 7/9] ARM: Kirkwood: Convert ib62x0 " Andrew Lunn
2012-10-24 20:40 ` Simon Baatz
2012-10-24 14:53 ` [PATCH 8/9] ARM: Kirkwood: Convert lsxl boards " Andrew Lunn
2012-10-24 20:37 ` Michael Walle
2012-10-28 16:40 ` Michael Walle
2012-10-24 14:53 ` [PATCH 9/9] ARM: Kirkwood: Convert IX2-200 " Andrew Lunn
2012-10-24 20:04 ` Thomas Petazzoni
2012-10-24 20:20 ` Andrew Lunn
2012-10-24 20:29 ` Thomas Petazzoni
2012-10-24 15:29 ` [PATCH 0/9] ARM: Kirkwood: Convert " Josh Coombs
2012-10-24 15:35 ` Andrew Lunn
2012-10-24 19:26 ` Thomas Petazzoni
2012-10-24 18:06 ` Michael Walle
2012-10-24 20:01 ` Andrew Lunn
2012-10-24 20:47 ` Michael Walle
2012-10-24 21:33 ` Thomas Petazzoni
2012-10-25 5:46 ` Andrew Lunn
2012-10-25 6:28 ` Thomas Petazzoni
2012-10-25 7:39 ` Michael Walle
2012-10-25 7:43 ` Thomas Petazzoni
2012-10-25 20:19 ` Michael Walle
2012-10-26 18:06 ` Michael Walle
2012-10-26 18:45 ` Thomas Petazzoni
2012-10-26 20:17 ` Michael Walle
2012-10-27 8:59 ` Andrew Lunn
2012-10-25 22:57 ` Jamie Lentin
2012-10-28 16:57 ` Andrew Lunn
2012-10-28 18:17 ` Michael Walle
2012-10-28 19:50 ` Simon Baatz
2012-10-28 20:01 ` Andrew Lunn [this message]
2012-10-28 21:06 ` Jamie Lentin
2012-10-31 22:38 ` Josh Coombs
2012-11-07 16:13 ` [RFC PATCH 0/2] Kirkwood 98dx4122 pinctrl variant Valentin Longchamp
2012-11-07 17:36 ` Andrew Lunn
2012-11-07 16:13 ` [PATCH 1/2] ARM: support 98DX412x kirkwoods with pinctrl Valentin Longchamp
2012-11-07 16:13 ` [PATCH 2/2] ARM: convert the km_kirkwood board to pinctrl Valentin Longchamp
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20121028200139.GG15143@lunn.ch \
--to=andrew@lunn$(echo .)ch \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox