From: voice.shen@atmel•com (Bo Shen)
To: linux-arm-kernel@lists•infradead.org
Subject: [V2 2/8] USB: EHCI: make ehci-atmel a separate driver
Date: Mon, 18 Feb 2013 17:44:46 +0800 [thread overview]
Message-ID: <5121F80E.1010501@atmel.com> (raw)
In-Reply-To: <1360923853-7875-3-git-send-email-manjunath.goudar@linaro.org>
On 02/15/2013 06:24 PM, Manjunath Goudar wrote:
> Separate the Atmel host controller driver from ehci-hcd host code
> into its own driver module.
>
> In V2:
> Resolved below compiler error.
> drivers/usb/host/ehci-atmel.c: In function 'ehci_atmel_drv_remove':
> drivers/usb/host/ehci-atmel.c:167: error: implicit declaration of function 'ehci_shutdown'
>
> Signed-off-by: Manjunath Goudar<manjunath.goudar@linaro•org>
> Cc: Alan Stern<stern@rowland•harvard.edu>
> Cc: Greg KH<greg@kroah•com>
> Cc: Grant Likely<grant.likely@secretlab•ca>
> Cc: Rob Herring<rob.herring@calxeda•com>
> Cc: Andrew Victor<linux@maxim•org.za>
> Cc: Nicolas Ferre<nicolas.ferre@atmel•com>
> Cc: Jean-Christophe Plagniol-Villard<plagnioj@jcrosoft•com>
> Cc: linux-usb at vger.kernel.org
> Cc: linux-kernel at vger.kernel.org
> ---
> drivers/usb/host/Kconfig | 8 +++++
> drivers/usb/host/Makefile | 1 +
> drivers/usb/host/ehci-atmel.c | 76 ++++++++++++++++++++++-------------------
> drivers/usb/host/ehci-hcd.c | 10 ++----
> drivers/usb/host/ehci.h | 2 +-
> 5 files changed, 53 insertions(+), 44 deletions(-)
>
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index 15e8032..1ef37d7 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -170,6 +170,14 @@ config USB_EHCI_HCD_SPEAR
> Enables support for the on-chip EHCI controller on
> ST SPEAr chips.
>
> +config USB_EHCI_HCD_AT91
> + tristate "Support for Atmel on-chip EHCI USB controller"
> + depends on USB_EHCI_HCD&& ARCH_AT91
> + default y
> + ---help---
> + Enables support for the on-chip EHCI controller on
> + Atmel chips.
> +
> config USB_EHCI_MSM
> bool "Support for MSM on-chip EHCI USB controller"
> depends on USB_EHCI_HCD&& ARCH_MSM
> diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
> index c8fcde9..b301243 100644
> --- a/drivers/usb/host/Makefile
> +++ b/drivers/usb/host/Makefile
> @@ -29,6 +29,7 @@ obj-$(CONFIG_USB_EHCI_HCD_PLATFORM) += ehci-platform.o
> obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
> obj-$(CONFIG_USB_EHCI_HCD_SPEAR)+= ehci-spear.o
> obj-$(CONFIG_USB_OXU210HP_HCD) += oxu210hp-hcd.o
> +obj-$(CONFIG_USB_EHCI_HCD_AT91) += ehci-atmel.o
> obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
> obj-$(CONFIG_USB_ISP1362_HCD) += isp1362-hcd.o
> obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o
> diff --git a/drivers/usb/host/ehci-atmel.c b/drivers/usb/host/ehci-atmel.c
> index 27639487..3cd0dd4 100644
> --- a/drivers/usb/host/ehci-atmel.c
> +++ b/drivers/usb/host/ehci-atmel.c
> @@ -15,6 +15,19 @@
> #include<linux/platform_device.h>
> #include<linux/of.h>
> #include<linux/of_platform.h>
> +#include<linux/kernel.h>
> +#include<linux/module.h>
> +#include<linux/usb.h>
> +#include<linux/usb/hcd.h>
> +#include<linux/io.h>
> +#include<linux/dma-mapping.h>
> +
> +#include "ehci.h"
> +
> +#define DRIVER_DESC "EHCI atmel driver"
> +
> +static const char hcd_name[] = "ehci-atmel";
> +static struct hc_driver __read_mostly ehci_atmel_hc_driver;
>
> /* interface and function clocks */
> static struct clk *iclk, *fclk;
> @@ -60,41 +73,6 @@ static int ehci_atmel_setup(struct usb_hcd *hcd)
> return ehci_setup(hcd);
> }
>
> -static const struct hc_driver ehci_atmel_hc_driver = {
> - .description = hcd_name,
> - .product_desc = "Atmel EHCI UHP HS",
> - .hcd_priv_size = sizeof(struct ehci_hcd),
> -
> - /* generic hardware linkage */
> - .irq = ehci_irq,
> - .flags = HCD_MEMORY | HCD_USB2,
> -
> - /* basic lifecycle operations */
> - .reset = ehci_atmel_setup,
> - .start = ehci_run,
> - .stop = ehci_stop,
> - .shutdown = ehci_shutdown,
> -
> - /* managing i/o requests and associated device resources */
> - .urb_enqueue = ehci_urb_enqueue,
> - .urb_dequeue = ehci_urb_dequeue,
> - .endpoint_disable = ehci_endpoint_disable,
> - .endpoint_reset = ehci_endpoint_reset,
> -
> - /* scheduling support */
> - .get_frame_number = ehci_get_frame,
> -
> - /* root hub support */
> - .hub_status_data = ehci_hub_status_data,
> - .hub_control = ehci_hub_control,
> - .bus_suspend = ehci_bus_suspend,
> - .bus_resume = ehci_bus_resume,
> - .relinquish_port = ehci_relinquish_port,
> - .port_handed_over = ehci_port_handed_over,
> -
> - .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
> -};
> -
> static u64 at91_ehci_dma_mask = DMA_BIT_MASK(32);
>
> static int ehci_atmel_drv_probe(struct platform_device *pdev)
> @@ -210,7 +188,33 @@ static struct platform_driver ehci_atmel_driver = {
> .remove = ehci_atmel_drv_remove,
> .shutdown = usb_hcd_platform_shutdown,
> .driver = {
> - .name = "atmel-ehci",
> + .name = hcd_name,
This change will cause atmel ehci won't work with the none device tree
kernel.
it can be fixed with replace other places using "atmel-ehci" with
<hcd_name>, that means replace "atmel-ehci" with "ehci-atmel" at other
places.
Best Regards,
Bo Shen
next prev parent reply other threads:[~2013-02-18 9:44 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-15 10:24 [V2 0/8] usb: ehci: more bus glues as separate modules Manjunath Goudar
2013-02-15 16:10 ` Arnd Bergmann
2013-02-15 18:07 ` Greg KH
2013-02-15 21:58 ` Arnd Bergmann
2013-02-15 22:12 ` [PATCH 1/2] USB: EHCI: make ehci-vt8500 a separate driver Arnd Bergmann
2013-02-15 22:12 ` [PATCH 2/2] USB: EHCI: make ehci-orion " Arnd Bergmann
2013-02-15 22:38 ` Jason Cooper
2013-02-16 8:42 ` Andrew Lunn
2013-02-16 14:19 ` Ezequiel Garcia
2013-02-16 23:03 ` [PATCH] USB: update host controller Kconfig entries Arnd Bergmann
2013-02-18 22:34 ` [PATCH 2/2] USB: EHCI: make ehci-orion a separate driver Alan Stern
2013-02-19 7:24 ` Andrew Lunn
2013-02-19 8:32 ` Arnaud Patard (Rtp)
2013-02-20 18:28 ` Greg KH
2013-02-20 18:44 ` Arnd Bergmann
[not found] ` <CAJFYCKGCNDTSq9OYZUYXx8XNSgSHD=p=hw+9_7N=EhM=bUu=bg@mail.gmail.com>
2013-02-19 10:56 ` Arnd Bergmann
2013-02-19 15:26 ` Alan Stern
2013-02-20 16:02 ` Alan Stern
2013-02-20 16:27 ` Arnd Bergmann
2013-02-20 16:54 ` Jason Cooper
2013-02-15 22:21 ` [PATCH 1/2] USB: EHCI: make ehci-vt8500 " Tony Prisk
2013-02-15 16:47 ` [V2 0/8] usb: ehci: more bus glues as separate modules Ezequiel Garcia
[not found] ` <1360923853-7875-3-git-send-email-manjunath.goudar@linaro.org>
2013-02-18 9:44 ` Bo Shen [this message]
2013-02-18 10:12 ` [V2 2/8] USB: EHCI: make ehci-atmel a separate driver Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5121F80E.1010501@atmel.com \
--to=voice.shen@atmel$(echo .)com \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox