From: gerg@uclinux•org (Greg Ungerer)
To: linux-arm-kernel@lists•infradead.org
Subject: [PATCH 2/8] ARM: imx: add clocking support code for the IMX50 SoC
Date: Wed, 23 Oct 2013 13:19:57 +1000 [thread overview]
Message-ID: <5267405D.4010104@uclinux.org> (raw)
In-Reply-To: <20131022122708.GA31304@pengutronix.de>
Hi Sascha,
On 22/10/13 22:27, Sascha Hauer wrote:
> Hi Greg,
>
> On Fri, Oct 18, 2013 at 04:04:14PM +1000, gerg at uclinux.org wrote:
>> From: Greg Ungerer <gerg@uclinux•org>
>>
>> Add code to support the specific clock tree of the Freescale IMX50 SoC.
>> It can use much of the common IMX51/IMX53 clocking code.
>>
>> Signed-off-by: Greg Ungerer <gerg@uclinux•org>
>> ---
>> + clk_register_clkdev(clk[i2c3_gate], NULL, "imx21-i2c.2");
>> + clk_register_clkdev(clk[fec_gate], NULL, "imx25-fec.0");
>> + clk_register_clkdev(clk[usb_phy1_gate], "usb_phy1", "mxc-ehci.0");
>> + clk_register_clkdev(clk[esdhc1_ipg_gate], "ipg", "sdhci-esdhc-imx50.0");
>> + clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx50.0");
>> + clk_register_clkdev(clk[esdhc1_per_gate], "per", "sdhci-esdhc-imx50.0");
>> + clk_register_clkdev(clk[esdhc2_ipg_gate], "ipg", "sdhci-esdhc-imx50.1");
>> + clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx50.1");
>> + clk_register_clkdev(clk[esdhc2_per_gate], "per", "sdhci-esdhc-imx50.1");
>> + clk_register_clkdev(clk[esdhc3_ipg_gate], "ipg", "sdhci-esdhc-imx50.2");
>> + clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx50.2");
>> + clk_register_clkdev(clk[esdhc3_per_gate], "per", "sdhci-esdhc-imx50.2");
>> + clk_register_clkdev(clk[esdhc4_ipg_gate], "ipg", "sdhci-esdhc-imx50.3");
>> + clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx50.3");
>> + clk_register_clkdev(clk[esdhc4_per_gate], "per", "sdhci-esdhc-imx50.3");
>
> The above shouldn't be needed with dt-only support. On i.MX51/53 these
> are only needed for platform based support.
Ok, thanks. I'll remove them.
Regards
Greg
next prev parent reply other threads:[~2013-10-23 3:19 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-10-18 6:04 [PATCH 0/8] ARM: imx: add IMX50 SoC support gerg at uclinux.org
2013-10-18 6:04 ` [PATCH 1/8] ARM: imx: add debug uart support for IMX50 SoC gerg at uclinux.org
2013-10-18 6:04 ` [PATCH 2/8] ARM: imx: add clocking support code for the " gerg at uclinux.org
2013-10-22 12:27 ` Sascha Hauer
2013-10-23 3:19 ` Greg Ungerer [this message]
2013-10-23 9:19 ` Jason Cooper
2013-10-23 12:44 ` Greg Ungerer
2013-10-23 13:42 ` Jason Cooper
2013-10-24 15:11 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 3/8] ARM: imx: add pinctrl " gerg at uclinux.org
2013-10-24 15:16 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 4/8] ARM: imx: add support code for IMX50 based machines gerg at uclinux.org
2013-10-24 11:11 ` Rob Herring
2013-10-28 6:38 ` Greg Ungerer
2013-10-28 19:57 ` Rob Herring
2013-10-18 6:04 ` [PATCH 5/8] ARM: imx: allow configuration of the IMX50 SoC gerg at uclinux.org
2013-10-24 15:17 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 6/8] ARM: dts: imx: add device tree pin definitions for the IMX50 gerg at uclinux.org
2013-10-18 6:04 ` [PATCH 7/8] ARM: dts: imx: add IMX50 SoC device tree bindings gerg at uclinux.org
2013-10-22 12:35 ` Sascha Hauer
2013-10-22 20:08 ` Matt Sealey
2013-10-22 21:57 ` Sascha Hauer
2013-10-22 22:42 ` Benoît Thébaudeau
2013-10-22 23:06 ` Matt Sealey
2013-10-23 0:17 ` Benoît Thébaudeau
2013-10-23 5:55 ` Greg Ungerer
2013-10-24 21:13 ` Matt Sealey
2013-10-23 5:40 ` Greg Ungerer
2013-10-24 15:26 ` Shawn Guo
2013-10-18 6:04 ` [PATCH 8/8] ARM: dts: imx: add device tree support for Freescale imx50evk board gerg at uclinux.org
2013-10-24 15:29 ` Shawn Guo
2013-10-23 9:14 ` [PATCH 0/8] ARM: imx: add IMX50 SoC support Jason Cooper
2013-10-23 12:39 ` Greg Ungerer
2013-10-24 15:00 ` Shawn Guo
2013-10-25 12:53 ` Greg Ungerer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5267405D.4010104@uclinux.org \
--to=gerg@uclinux$(echo .)org \
--cc=linux-arm-kernel@lists$(echo .)infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox