* [PATCH RESEND v2 1/4] ARM: dts: exynos4: convert magic numbers to macros in clock bindings
2014-02-24 13:22 [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Andrzej Hajda
@ 2014-02-24 13:22 ` Andrzej Hajda
2014-02-24 13:22 ` [PATCH RESEND v2 2/4] ARM: dts: exynos5250: " Andrzej Hajda
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Andrzej Hajda @ 2014-02-24 13:22 UTC (permalink / raw)
To: linux-arm-kernel
The patch replaces magic numbers with macros defined in DT header
in exynos4 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung•com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung•com>
Acked-by: Tomasz Figa <t.figa@samsung•com>
Acked-by: Mike Turquette <mturquette@linaro•org>
---
.../devicetree/bindings/clock/exynos4-clock.txt | 259 +--------------------
arch/arm/boot/dts/exynos4.dtsi | 73 +++---
arch/arm/boot/dts/exynos4210.dtsi | 9 +-
arch/arm/boot/dts/exynos4x12.dtsi | 34 +--
4 files changed, 69 insertions(+), 306 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt
index a2ac2d9..f5a5b19 100644
--- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt
+++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt
@@ -15,259 +15,12 @@ Required Properties:
- #clock-cells: should be 1.
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume. Some of the clocks are available only on a particular
-Exynos4 SoC and this is specified where applicable.
-
-
- [Core Clocks]
-
- Clock ID SoC (if specific)
- -----------------------------------------------
-
- xxti 1
- xusbxti 2
- fin_pll 3
- fout_apll 4
- fout_mpll 5
- fout_epll 6
- fout_vpll 7
- sclk_apll 8
- sclk_mpll 9
- sclk_epll 10
- sclk_vpll 11
- arm_clk 12
- aclk200 13
- aclk100 14
- aclk160 15
- aclk133 16
- mout_mpll_user_t 17 Exynos4x12
- mout_mpll_user_c 18 Exynos4x12
- mout_core 19
- mout_apll 20
-
-
- [Clock Gate for Special Clocks]
-
- Clock ID SoC (if specific)
- -----------------------------------------------
-
- sclk_fimc0 128
- sclk_fimc1 129
- sclk_fimc2 130
- sclk_fimc3 131
- sclk_cam0 132
- sclk_cam1 133
- sclk_csis0 134
- sclk_csis1 135
- sclk_hdmi 136
- sclk_mixer 137
- sclk_dac 138
- sclk_pixel 139
- sclk_fimd0 140
- sclk_mdnie0 141 Exynos4412
- sclk_mdnie_pwm0 12 142 Exynos4412
- sclk_mipi0 143
- sclk_audio0 144
- sclk_mmc0 145
- sclk_mmc1 146
- sclk_mmc2 147
- sclk_mmc3 148
- sclk_mmc4 149
- sclk_sata 150 Exynos4210
- sclk_uart0 151
- sclk_uart1 152
- sclk_uart2 153
- sclk_uart3 154
- sclk_uart4 155
- sclk_audio1 156
- sclk_audio2 157
- sclk_spdif 158
- sclk_spi0 159
- sclk_spi1 160
- sclk_spi2 161
- sclk_slimbus 162
- sclk_fimd1 163 Exynos4210
- sclk_mipi1 164 Exynos4210
- sclk_pcm1 165
- sclk_pcm2 166
- sclk_i2s1 167
- sclk_i2s2 168
- sclk_mipihsi 169 Exynos4412
- sclk_mfc 170
- sclk_pcm0 171
- sclk_g3d 172
- sclk_pwm_isp 173 Exynos4x12
- sclk_spi0_isp 174 Exynos4x12
- sclk_spi1_isp 175 Exynos4x12
- sclk_uart_isp 176 Exynos4x12
- sclk_fimg2d 177
-
- [Peripheral Clock Gates]
-
- Clock ID SoC (if specific)
- -----------------------------------------------
-
- fimc0 256
- fimc1 257
- fimc2 258
- fimc3 259
- csis0 260
- csis1 261
- jpeg 262
- smmu_fimc0 263
- smmu_fimc1 264
- smmu_fimc2 265
- smmu_fimc3 266
- smmu_jpeg 267
- vp 268
- mixer 269
- tvenc 270 Exynos4210
- hdmi 271
- smmu_tv 272
- mfc 273
- smmu_mfcl 274
- smmu_mfcr 275
- g3d 276
- g2d 277
- rotator 278 Exynos4210
- mdma 279 Exynos4210
- smmu_g2d 280 Exynos4210
- smmu_rotator 281 Exynos4210
- smmu_mdma 282 Exynos4210
- fimd0 283
- mie0 284
- mdnie0 285 Exynos4412
- dsim0 286
- smmu_fimd0 287
- fimd1 288 Exynos4210
- mie1 289 Exynos4210
- dsim1 290 Exynos4210
- smmu_fimd1 291 Exynos4210
- pdma0 292
- pdma1 293
- pcie_phy 294
- sata_phy 295 Exynos4210
- tsi 296
- sdmmc0 297
- sdmmc1 298
- sdmmc2 299
- sdmmc3 300
- sdmmc4 301
- sata 302 Exynos4210
- sromc 303
- usb_host 304
- usb_device 305
- pcie 306
- onenand 307
- nfcon 308
- smmu_pcie 309
- gps 310
- smmu_gps 311
- uart0 312
- uart1 313
- uart2 314
- uart3 315
- uart4 316
- i2c0 317
- i2c1 318
- i2c2 319
- i2c3 320
- i2c4 321
- i2c5 322
- i2c6 323
- i2c7 324
- i2c_hdmi 325
- tsadc 326
- spi0 327
- spi1 328
- spi2 329
- i2s1 330
- i2s2 331
- pcm0 332
- i2s0 333
- pcm1 334
- pcm2 335
- pwm 336
- slimbus 337
- spdif 338
- ac97 339
- modemif 340
- chipid 341
- sysreg 342
- hdmi_cec 343
- mct 344
- wdt 345
- rtc 346
- keyif 347
- audss 348
- mipi_hsi 349 Exynos4210
- mdma2 350 Exynos4210
- pixelasyncm0 351
- pixelasyncm1 352
- fimc_lite0 353 Exynos4x12
- fimc_lite1 354 Exynos4x12
- ppmuispx 355 Exynos4x12
- ppmuispmx 356 Exynos4x12
- fimc_isp 357 Exynos4x12
- fimc_drc 358 Exynos4x12
- fimc_fd 359 Exynos4x12
- mcuisp 360 Exynos4x12
- gicisp 361 Exynos4x12
- smmu_isp 362 Exynos4x12
- smmu_drc 363 Exynos4x12
- smmu_fd 364 Exynos4x12
- smmu_lite0 365 Exynos4x12
- smmu_lite1 366 Exynos4x12
- mcuctl_isp 367 Exynos4x12
- mpwm_isp 368 Exynos4x12
- i2c0_isp 369 Exynos4x12
- i2c1_isp 370 Exynos4x12
- mtcadc_isp 371 Exynos4x12
- pwm_isp 372 Exynos4x12
- wdt_isp 373 Exynos4x12
- uart_isp 374 Exynos4x12
- asyncaxim 375 Exynos4x12
- smmu_ispcx 376 Exynos4x12
- spi0_isp 377 Exynos4x12
- spi1_isp 378 Exynos4x12
- pwm_isp_sclk 379 Exynos4x12
- spi0_isp_sclk 380 Exynos4x12
- spi1_isp_sclk 381 Exynos4x12
- uart_isp_sclk 382 Exynos4x12
- tmu_apbif 383
-
- [Mux Clocks]
-
- Clock ID SoC (if specific)
- -----------------------------------------------
-
- mout_fimc0 384
- mout_fimc1 385
- mout_fimc2 386
- mout_fimc3 387
- mout_cam0 388
- mout_cam1 389
- mout_csis0 390
- mout_csis1 391
- mout_g3d0 392
- mout_g3d1 393
- mout_g3d 394
- aclk400_mcuisp 395 Exynos4x12
-
- [Div Clocks]
-
- Clock ID SoC (if specific)
- -----------------------------------------------
-
- div_isp0 450 Exynos4x12
- div_isp1 451 Exynos4x12
- div_mcuisp0 452 Exynos4x12
- div_mcuisp1 453 Exynos4x12
- div_aclk200 454 Exynos4x12
- div_aclk400_mcuisp 455 Exynos4x12
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos4.h header and can be used in device
+tree sources.
Example 1: An example of a clock controller node is listed below.
@@ -285,6 +38,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
compatible = "samsung,exynos4210-uart";
reg = <0x13820000 0x100>;
interrupts = <0 54 0>;
- clocks = <&clock 314>, <&clock 153>;
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
clock-names = "uart", "clk_uart_baud0";
};
diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
index 08452e1..28b5ec7 100644
--- a/arch/arm/boot/dts/exynos4.dtsi
+++ b/arch/arm/boot/dts/exynos4.dtsi
@@ -19,6 +19,7 @@
* published by the Free Software Foundation.
*/
+#include <dt-bindings/clock/exynos4.h>
#include "skeleton.dtsi"
/ {
@@ -119,7 +120,7 @@
compatible = "samsung,exynos4210-fimc";
reg = <0x11800000 0x1000>;
interrupts = <0 84 0>;
- clocks = <&clock 256>, <&clock 128>;
+ clocks = <&clock CLK_FIMC0>, <&clock CLK_SCLK_FIMC0>;
clock-names = "fimc", "sclk_fimc";
samsung,power-domain = <&pd_cam>;
samsung,sysreg = <&sys_reg>;
@@ -130,7 +131,7 @@
compatible = "samsung,exynos4210-fimc";
reg = <0x11810000 0x1000>;
interrupts = <0 85 0>;
- clocks = <&clock 257>, <&clock 129>;
+ clocks = <&clock CLK_FIMC1>, <&clock CLK_SCLK_FIMC1>;
clock-names = "fimc", "sclk_fimc";
samsung,power-domain = <&pd_cam>;
samsung,sysreg = <&sys_reg>;
@@ -141,7 +142,7 @@
compatible = "samsung,exynos4210-fimc";
reg = <0x11820000 0x1000>;
interrupts = <0 86 0>;
- clocks = <&clock 258>, <&clock 130>;
+ clocks = <&clock CLK_FIMC2>, <&clock CLK_SCLK_FIMC2>;
clock-names = "fimc", "sclk_fimc";
samsung,power-domain = <&pd_cam>;
samsung,sysreg = <&sys_reg>;
@@ -152,7 +153,7 @@
compatible = "samsung,exynos4210-fimc";
reg = <0x11830000 0x1000>;
interrupts = <0 87 0>;
- clocks = <&clock 259>, <&clock 131>;
+ clocks = <&clock CLK_FIMC3>, <&clock CLK_SCLK_FIMC3>;
clock-names = "fimc", "sclk_fimc";
samsung,power-domain = <&pd_cam>;
samsung,sysreg = <&sys_reg>;
@@ -163,7 +164,7 @@
compatible = "samsung,exynos4210-csis";
reg = <0x11880000 0x4000>;
interrupts = <0 78 0>;
- clocks = <&clock 260>, <&clock 134>;
+ clocks = <&clock CLK_CSIS0>, <&clock CLK_SCLK_CSIS0>;
clock-names = "csis", "sclk_csis";
bus-width = <4>;
samsung,power-domain = <&pd_cam>;
@@ -178,7 +179,7 @@
compatible = "samsung,exynos4210-csis";
reg = <0x11890000 0x4000>;
interrupts = <0 80 0>;
- clocks = <&clock 261>, <&clock 135>;
+ clocks = <&clock CLK_CSIS1>, <&clock CLK_SCLK_CSIS1>;
clock-names = "csis", "sclk_csis";
bus-width = <2>;
samsung,power-domain = <&pd_cam>;
@@ -194,7 +195,7 @@
compatible = "samsung,s3c2410-wdt";
reg = <0x10060000 0x100>;
interrupts = <0 43 0>;
- clocks = <&clock 345>;
+ clocks = <&clock CLK_WDT>;
clock-names = "watchdog";
status = "disabled";
};
@@ -203,7 +204,7 @@
compatible = "samsung,s3c6410-rtc";
reg = <0x10070000 0x100>;
interrupts = <0 44 0>, <0 45 0>;
- clocks = <&clock 346>;
+ clocks = <&clock CLK_RTC>;
clock-names = "rtc";
status = "disabled";
};
@@ -212,7 +213,7 @@
compatible = "samsung,s5pv210-keypad";
reg = <0x100A0000 0x100>;
interrupts = <0 109 0>;
- clocks = <&clock 347>;
+ clocks = <&clock CLK_KEYIF>;
clock-names = "keypad";
status = "disabled";
};
@@ -221,7 +222,7 @@
compatible = "samsung,exynos4210-sdhci";
reg = <0x12510000 0x100>;
interrupts = <0 73 0>;
- clocks = <&clock 297>, <&clock 145>;
+ clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>;
clock-names = "hsmmc", "mmc_busclk.2";
status = "disabled";
};
@@ -230,7 +231,7 @@
compatible = "samsung,exynos4210-sdhci";
reg = <0x12520000 0x100>;
interrupts = <0 74 0>;
- clocks = <&clock 298>, <&clock 146>;
+ clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>;
clock-names = "hsmmc", "mmc_busclk.2";
status = "disabled";
};
@@ -239,7 +240,7 @@
compatible = "samsung,exynos4210-sdhci";
reg = <0x12530000 0x100>;
interrupts = <0 75 0>;
- clocks = <&clock 299>, <&clock 147>;
+ clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>;
clock-names = "hsmmc", "mmc_busclk.2";
status = "disabled";
};
@@ -248,7 +249,7 @@
compatible = "samsung,exynos4210-sdhci";
reg = <0x12540000 0x100>;
interrupts = <0 76 0>;
- clocks = <&clock 300>, <&clock 148>;
+ clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>;
clock-names = "hsmmc", "mmc_busclk.2";
status = "disabled";
};
@@ -257,7 +258,7 @@
compatible = "samsung,exynos4210-ehci";
reg = <0x12580000 0x100>;
interrupts = <0 70 0>;
- clocks = <&clock 304>;
+ clocks = <&clock CLK_USB_HOST>;
clock-names = "usbhost";
status = "disabled";
};
@@ -266,7 +267,7 @@
compatible = "samsung,exynos4210-ohci";
reg = <0x12590000 0x100>;
interrupts = <0 70 0>;
- clocks = <&clock 304>;
+ clocks = <&clock CLK_USB_HOST>;
clock-names = "usbhost";
status = "disabled";
};
@@ -276,7 +277,7 @@
reg = <0x13400000 0x10000>;
interrupts = <0 94 0>;
samsung,power-domain = <&pd_mfc>;
- clocks = <&clock 273>;
+ clocks = <&clock CLK_MFC>;
clock-names = "mfc";
status = "disabled";
};
@@ -285,7 +286,7 @@
compatible = "samsung,exynos4210-uart";
reg = <0x13800000 0x100>;
interrupts = <0 52 0>;
- clocks = <&clock 312>, <&clock 151>;
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
clock-names = "uart", "clk_uart_baud0";
status = "disabled";
};
@@ -294,7 +295,7 @@
compatible = "samsung,exynos4210-uart";
reg = <0x13810000 0x100>;
interrupts = <0 53 0>;
- clocks = <&clock 313>, <&clock 152>;
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
clock-names = "uart", "clk_uart_baud0";
status = "disabled";
};
@@ -303,7 +304,7 @@
compatible = "samsung,exynos4210-uart";
reg = <0x13820000 0x100>;
interrupts = <0 54 0>;
- clocks = <&clock 314>, <&clock 153>;
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
clock-names = "uart", "clk_uart_baud0";
status = "disabled";
};
@@ -312,7 +313,7 @@
compatible = "samsung,exynos4210-uart";
reg = <0x13830000 0x100>;
interrupts = <0 55 0>;
- clocks = <&clock 315>, <&clock 154>;
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
clock-names = "uart", "clk_uart_baud0";
status = "disabled";
};
@@ -323,7 +324,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x13860000 0x100>;
interrupts = <0 58 0>;
- clocks = <&clock 317>;
+ clocks = <&clock CLK_I2C0>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_bus>;
@@ -336,7 +337,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x13870000 0x100>;
interrupts = <0 59 0>;
- clocks = <&clock 318>;
+ clocks = <&clock CLK_I2C1>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_bus>;
@@ -349,7 +350,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x13880000 0x100>;
interrupts = <0 60 0>;
- clocks = <&clock 319>;
+ clocks = <&clock CLK_I2C2>;
clock-names = "i2c";
status = "disabled";
};
@@ -360,7 +361,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x13890000 0x100>;
interrupts = <0 61 0>;
- clocks = <&clock 320>;
+ clocks = <&clock CLK_I2C3>;
clock-names = "i2c";
status = "disabled";
};
@@ -371,7 +372,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x138A0000 0x100>;
interrupts = <0 62 0>;
- clocks = <&clock 321>;
+ clocks = <&clock CLK_I2C4>;
clock-names = "i2c";
status = "disabled";
};
@@ -382,7 +383,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x138B0000 0x100>;
interrupts = <0 63 0>;
- clocks = <&clock 322>;
+ clocks = <&clock CLK_I2C5>;
clock-names = "i2c";
status = "disabled";
};
@@ -393,7 +394,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x138C0000 0x100>;
interrupts = <0 64 0>;
- clocks = <&clock 323>;
+ clocks = <&clock CLK_I2C6>;
clock-names = "i2c";
status = "disabled";
};
@@ -404,7 +405,7 @@
compatible = "samsung,s3c2440-i2c";
reg = <0x138D0000 0x100>;
interrupts = <0 65 0>;
- clocks = <&clock 324>;
+ clocks = <&clock CLK_I2C7>;
clock-names = "i2c";
status = "disabled";
};
@@ -417,7 +418,7 @@
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 327>, <&clock 159>;
+ clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
clock-names = "spi", "spi_busclk0";
pinctrl-names = "default";
pinctrl-0 = <&spi0_bus>;
@@ -432,7 +433,7 @@
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 328>, <&clock 160>;
+ clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
clock-names = "spi", "spi_busclk0";
pinctrl-names = "default";
pinctrl-0 = <&spi1_bus>;
@@ -447,7 +448,7 @@
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 329>, <&clock 161>;
+ clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
clock-names = "spi", "spi_busclk0";
pinctrl-names = "default";
pinctrl-0 = <&spi2_bus>;
@@ -458,7 +459,7 @@
compatible = "samsung,exynos4210-pwm";
reg = <0x139D0000 0x1000>;
interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>, <0 41 0>;
- clocks = <&clock 336>;
+ clocks = <&clock CLK_PWM>;
clock-names = "timers";
#pwm-cells = <2>;
status = "disabled";
@@ -475,7 +476,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x12680000 0x1000>;
interrupts = <0 35 0>;
- clocks = <&clock 292>;
+ clocks = <&clock CLK_PDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -486,7 +487,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x12690000 0x1000>;
interrupts = <0 36 0>;
- clocks = <&clock 293>;
+ clocks = <&clock CLK_PDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -497,7 +498,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x12850000 0x1000>;
interrupts = <0 34 0>;
- clocks = <&clock 279>;
+ clocks = <&clock CLK_MDMA>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -511,7 +512,7 @@
reg = <0x11c00000 0x20000>;
interrupt-names = "fifo", "vsync", "lcd_sys";
interrupts = <11 0>, <11 1>, <11 2>;
- clocks = <&clock 140>, <&clock 283>;
+ clocks = <&clock CLK_SCLK_FIMD0>, <&clock CLK_FIMD0>;
clock-names = "sclk_fimd", "fimd";
samsung,power-domain = <&pd_lcd0>;
status = "disabled";
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 48ecd7a..cb0e768d 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -53,7 +53,7 @@
reg = <0x10050000 0x800>;
interrupt-parent = <&mct_map>;
interrupts = <0>, <1>, <2>, <3>, <4>, <5>;
- clocks = <&clock 3>, <&clock 344>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
clock-names = "fin_pll", "mct";
mct_map: mct-map {
@@ -109,7 +109,7 @@
interrupt-parent = <&combiner>;
reg = <0x100C0000 0x100>;
interrupts = <2 4>;
- clocks = <&clock 383>;
+ clocks = <&clock CLK_TMU_APBIF>;
clock-names = "tmu_apbif";
status = "disabled";
};
@@ -118,13 +118,14 @@
compatible = "samsung,s5pv210-g2d";
reg = <0x12800000 0x1000>;
interrupts = <0 89 0>;
- clocks = <&clock 177>, <&clock 277>;
+ clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>;
clock-names = "sclk_fimg2d", "fimg2d";
status = "disabled";
};
camera {
- clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>;
+ clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>,
+ <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
fimc_0: fimc at 11800000 {
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 5c412aa..e0eb6bb 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -47,7 +47,7 @@
reg = <0x10050000 0x800>;
interrupt-parent = <&mct_map>;
interrupts = <0>, <1>, <2>, <3>, <4>;
- clocks = <&clock 3>, <&clock 344>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
clock-names = "fin_pll", "mct";
mct_map: mct-map {
@@ -97,13 +97,14 @@
compatible = "samsung,exynos4212-g2d";
reg = <0x10800000 0x1000>;
interrupts = <0 89 0>;
- clocks = <&clock 177>, <&clock 277>;
+ clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>;
clock-names = "sclk_fimg2d", "fimg2d";
status = "disabled";
};
camera {
- clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>;
+ clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>,
+ <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
fimc_0: fimc at 11800000 {
@@ -145,7 +146,7 @@
reg = <0x12390000 0x1000>;
interrupts = <0 105 0>;
samsung,power-domain = <&pd_isp>;
- clocks = <&clock 353>;
+ clocks = <&clock CLK_FIMC_LITE0>;
clock-names = "flite";
status = "disabled";
};
@@ -155,7 +156,7 @@
reg = <0x123A0000 0x1000>;
interrupts = <0 106 0>;
samsung,power-domain = <&pd_isp>;
- clocks = <&clock 354>;
+ clocks = <&clock CLK_FIMC_LITE1>;
clock-names = "flite";
status = "disabled";
};
@@ -165,12 +166,19 @@
reg = <0x12000000 0x260000>;
interrupts = <0 90 0>, <0 95 0>;
samsung,power-domain = <&pd_isp>;
- clocks = <&clock 353>, <&clock 354>, <&clock 355>,
- <&clock 356>, <&clock 17>, <&clock 357>,
- <&clock 358>, <&clock 359>, <&clock 360>,
- <&clock 450>,<&clock 451>, <&clock 452>,
- <&clock 453>, <&clock 176>, <&clock 13>,
- <&clock 454>, <&clock 395>, <&clock 455>;
+ clocks = <&clock CLK_FIMC_LITE0>,
+ <&clock CLK_FIMC_LITE1>, <&clock CLK_PPMUISPX>,
+ <&clock CLK_PPMUISPMX>,
+ <&clock CLK_MOUT_MPLL_USER_T>,
+ <&clock CLK_FIMC_ISP>, <&clock CLK_FIMC_DRC>,
+ <&clock CLK_FIMC_FD>, <&clock CLK_MCUISP>,
+ <&clock CLK_DIV_ISP0>,<&clock CLK_DIV_ISP1>,
+ <&clock CLK_DIV_MCUISP0>,
+ <&clock CLK_DIV_MCUISP1>,
+ <&clock CLK_SCLK_UART_ISP>,
+ <&clock CLK_ACLK200>, <&clock CLK_DIV_ACLK200>,
+ <&clock CLK_ACLK400_MCUISP>,
+ <&clock CLK_DIV_ACLK400_MCUISP>;
clock-names = "lite0", "lite1", "ppmuispx",
"ppmuispmx", "mpll", "isp",
"drc", "fd", "mcuisp",
@@ -190,7 +198,7 @@
i2c1_isp: i2c-isp at 12140000 {
compatible = "samsung,exynos4212-i2c-isp";
reg = <0x12140000 0x100>;
- clocks = <&clock 370>;
+ clocks = <&clock CLK_I2C1_ISP>;
clock-names = "i2c_isp";
#address-cells = <1>;
#size-cells = <0>;
@@ -205,7 +213,7 @@
#address-cells = <1>;
#size-cells = <0>;
fifo-depth = <0x80>;
- clocks = <&clock 301>, <&clock 149>;
+ clocks = <&clock CLK_SDMMC4>, <&clock CLK_SCLK_MMC4>;
clock-names = "biu", "ciu";
status = "disabled";
};
--
1.8.3.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH RESEND v2 2/4] ARM: dts: exynos5250: convert magic numbers to macros in clock bindings
2014-02-24 13:22 [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Andrzej Hajda
2014-02-24 13:22 ` [PATCH RESEND v2 1/4] ARM: dts: exynos4: convert magic numbers to macros in clock bindings Andrzej Hajda
@ 2014-02-24 13:22 ` Andrzej Hajda
2014-02-24 13:22 ` [PATCH RESEND v2 3/4] ARM: dts: exynos5420: " Andrzej Hajda
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Andrzej Hajda @ 2014-02-24 13:22 UTC (permalink / raw)
To: linux-arm-kernel
The patch replaces magic numbers with macros defined in DT header
in exynos5250 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung•com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung•com>
Acked-by: Tomasz Figa <t.figa@samsung•com>
Acked-by: Mike Turquette <mturquette@linaro•org>
---
.../devicetree/bindings/clock/exynos5250-clock.txt | 163 +--------------------
arch/arm/boot/dts/exynos5250.dtsi | 105 ++++++-------
2 files changed, 60 insertions(+), 208 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt
index 72ce617..536eacd 100644
--- a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt
+++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt
@@ -13,163 +13,12 @@ Required Properties:
- #clock-cells: should be 1.
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
-
-
- [Core Clocks]
-
- Clock ID
- ----------------------------
-
- fin_pll 1
-
- [Clock Gate for Special Clocks]
-
- Clock ID
- ----------------------------
-
- sclk_cam_bayer 128
- sclk_cam0 129
- sclk_cam1 130
- sclk_gscl_wa 131
- sclk_gscl_wb 132
- sclk_fimd1 133
- sclk_mipi1 134
- sclk_dp 135
- sclk_hdmi 136
- sclk_pixel 137
- sclk_audio0 138
- sclk_mmc0 139
- sclk_mmc1 140
- sclk_mmc2 141
- sclk_mmc3 142
- sclk_sata 143
- sclk_usb3 144
- sclk_jpeg 145
- sclk_uart0 146
- sclk_uart1 147
- sclk_uart2 148
- sclk_uart3 149
- sclk_pwm 150
- sclk_audio1 151
- sclk_audio2 152
- sclk_spdif 153
- sclk_spi0 154
- sclk_spi1 155
- sclk_spi2 156
- div_i2s1 157
- div_i2s2 158
- sclk_hdmiphy 159
- div_pcm0 160
-
-
- [Peripheral Clock Gates]
-
- Clock ID
- ----------------------------
-
- gscl0 256
- gscl1 257
- gscl2 258
- gscl3 259
- gscl_wa 260
- gscl_wb 261
- smmu_gscl0 262
- smmu_gscl1 263
- smmu_gscl2 264
- smmu_gscl3 265
- mfc 266
- smmu_mfcl 267
- smmu_mfcr 268
- rotator 269
- jpeg 270
- mdma1 271
- smmu_rotator 272
- smmu_jpeg 273
- smmu_mdma1 274
- pdma0 275
- pdma1 276
- sata 277
- usbotg 278
- mipi_hsi 279
- sdmmc0 280
- sdmmc1 281
- sdmmc2 282
- sdmmc3 283
- sromc 284
- usb2 285
- usb3 286
- sata_phyctrl 287
- sata_phyi2c 288
- uart0 289
- uart1 290
- uart2 291
- uart3 292
- uart4 293
- i2c0 294
- i2c1 295
- i2c2 296
- i2c3 297
- i2c4 298
- i2c5 299
- i2c6 300
- i2c7 301
- i2c_hdmi 302
- adc 303
- spi0 304
- spi1 305
- spi2 306
- i2s1 307
- i2s2 308
- pcm1 309
- pcm2 310
- pwm 311
- spdif 312
- ac97 313
- hsi2c0 314
- hsi2c1 315
- hs12c2 316
- hs12c3 317
- chipid 318
- sysreg 319
- pmu 320
- cmu_top 321
- cmu_core 322
- cmu_mem 323
- tzpc0 324
- tzpc1 325
- tzpc2 326
- tzpc3 327
- tzpc4 328
- tzpc5 329
- tzpc6 330
- tzpc7 331
- tzpc8 332
- tzpc9 333
- hdmi_cec 334
- mct 335
- wdt 336
- rtc 337
- tmu 338
- fimd1 339
- mie1 340
- dsim0 341
- dp 342
- mixer 343
- hdmi 344
- g2d 345
- mdma0 346
- smmu_mdma0 347
-
-
- [Clock Muxes]
-
- Clock ID
- ----------------------------
- mout_hdmi 1024
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5250.h header and can be used in device
+tree sources.
Example 1: An example of a clock controller node is listed below.
@@ -187,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
compatible = "samsung,exynos4210-uart";
reg = <0x13820000 0x100>;
interrupts = <0 54 0>;
- clocks = <&clock 314>, <&clock 153>;
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
clock-names = "uart", "clk_uart_baud0";
};
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 8f6300f..987cfbe 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -17,6 +17,7 @@
* published by the Free Software Foundation.
*/
+#include <dt-bindings/clock/exynos5250.h>
#include "exynos5.dtsi"
#include "exynos5250-pinctrl.dtsi"
@@ -90,7 +91,8 @@
compatible = "samsung,exynos5250-audss-clock";
reg = <0x03810000 0x0C>;
#clock-cells = <1>;
- clocks = <&clock 1>, <&clock 7>, <&clock 138>, <&clock 160>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+ <&clock CLK_SCLK_AUDIO0>, <&clock CLK_DIV_PCM0>;
clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
};
@@ -115,7 +117,7 @@
interrupt-parent = <&mct_map>;
interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
<4 0>, <5 0>;
- clocks = <&clock 1>, <&clock 335>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
clock-names = "fin_pll", "mct";
mct_map: mct-map {
@@ -176,7 +178,7 @@
compatible = "samsung,exynos5250-wdt";
reg = <0x101D0000 0x100>;
interrupts = <0 42 0>;
- clocks = <&clock 336>;
+ clocks = <&clock CLK_WDT>;
clock-names = "watchdog";
samsung,syscon-phandle = <&pmu_system_controller>;
};
@@ -185,7 +187,7 @@
compatible = "samsung,exynos5250-g2d";
reg = <0x10850000 0x1000>;
interrupts = <0 91 0>;
- clocks = <&clock 345>;
+ clocks = <&clock CLK_G2D>;
clock-names = "fimg2d";
};
@@ -194,12 +196,12 @@
reg = <0x11000000 0x10000>;
interrupts = <0 96 0>;
samsung,power-domain = <&pd_mfc>;
- clocks = <&clock 266>;
+ clocks = <&clock CLK_MFC>;
clock-names = "mfc";
};
rtc at 101E0000 {
- clocks = <&clock 337>;
+ clocks = <&clock CLK_RTC>;
clock-names = "rtc";
status = "disabled";
};
@@ -208,27 +210,27 @@
compatible = "samsung,exynos5250-tmu";
reg = <0x10060000 0x100>;
interrupts = <0 65 0>;
- clocks = <&clock 338>;
+ clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
};
serial at 12C00000 {
- clocks = <&clock 289>, <&clock 146>;
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
clock-names = "uart", "clk_uart_baud0";
};
serial at 12C10000 {
- clocks = <&clock 290>, <&clock 147>;
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
clock-names = "uart", "clk_uart_baud0";
};
serial at 12C20000 {
- clocks = <&clock 291>, <&clock 148>;
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
clock-names = "uart", "clk_uart_baud0";
};
serial at 12C30000 {
- clocks = <&clock 292>, <&clock 149>;
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
clock-names = "uart", "clk_uart_baud0";
};
@@ -236,7 +238,7 @@
compatible = "samsung,exynos5-sata-ahci";
reg = <0x122F0000 0x1ff>;
interrupts = <0 115 0>;
- clocks = <&clock 277>, <&clock 143>;
+ clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>;
clock-names = "sata", "sclk_sata";
};
@@ -251,7 +253,7 @@
interrupts = <0 56 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 294>;
+ clocks = <&clock CLK_I2C0>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_bus>;
@@ -264,7 +266,7 @@
interrupts = <0 57 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 295>;
+ clocks = <&clock CLK_I2C1>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_bus>;
@@ -277,7 +279,7 @@
interrupts = <0 58 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 296>;
+ clocks = <&clock CLK_I2C2>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c2_bus>;
@@ -290,7 +292,7 @@
interrupts = <0 59 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 297>;
+ clocks = <&clock CLK_I2C3>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_bus>;
@@ -303,7 +305,7 @@
interrupts = <0 60 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 298>;
+ clocks = <&clock CLK_I2C4>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c4_bus>;
@@ -316,7 +318,7 @@
interrupts = <0 61 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 299>;
+ clocks = <&clock CLK_I2C5>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c5_bus>;
@@ -329,7 +331,7 @@
interrupts = <0 62 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 300>;
+ clocks = <&clock CLK_I2C6>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c6_bus>;
@@ -342,7 +344,7 @@
interrupts = <0 63 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 301>;
+ clocks = <&clock CLK_I2C7>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c7_bus>;
@@ -355,7 +357,7 @@
interrupts = <0 64 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 302>;
+ clocks = <&clock CLK_I2C_HDMI>;
clock-names = "i2c";
status = "disabled";
};
@@ -365,7 +367,7 @@
reg = <0x121D0000 0x100>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 288>;
+ clocks = <&clock CLK_SATA_PHYI2C>;
clock-names = "i2c";
status = "disabled";
};
@@ -380,7 +382,7 @@
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 304>, <&clock 154>;
+ clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
clock-names = "spi", "spi_busclk0";
pinctrl-names = "default";
pinctrl-0 = <&spi0_bus>;
@@ -396,7 +398,7 @@
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 305>, <&clock 155>;
+ clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
clock-names = "spi", "spi_busclk0";
pinctrl-names = "default";
pinctrl-0 = <&spi1_bus>;
@@ -412,7 +414,7 @@
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 306>, <&clock 156>;
+ clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
clock-names = "spi", "spi_busclk0";
pinctrl-names = "default";
pinctrl-0 = <&spi2_bus>;
@@ -424,7 +426,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12200000 0x1000>;
- clocks = <&clock 280>, <&clock 139>;
+ clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>;
clock-names = "biu", "ciu";
fifo-depth = <0x80>;
status = "disabled";
@@ -436,7 +438,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12210000 0x1000>;
- clocks = <&clock 281>, <&clock 140>;
+ clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>;
clock-names = "biu", "ciu";
fifo-depth = <0x80>;
status = "disabled";
@@ -448,7 +450,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12220000 0x1000>;
- clocks = <&clock 282>, <&clock 141>;
+ clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>;
clock-names = "biu", "ciu";
fifo-depth = <0x80>;
status = "disabled";
@@ -460,7 +462,7 @@
interrupts = <0 78 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 283>, <&clock 142>;
+ clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>;
clock-names = "biu", "ciu";
fifo-depth = <0x80>;
status = "disabled";
@@ -490,7 +492,7 @@
dmas = <&pdma1 12
&pdma1 11>;
dma-names = "tx", "rx";
- clocks = <&clock 307>, <&clock 157>;
+ clocks = <&clock CLK_I2S1>, <&clock CLK_DIV_I2S1>;
clock-names = "iis", "i2s_opclk0";
pinctrl-names = "default";
pinctrl-0 = <&i2s1_bus>;
@@ -503,7 +505,7 @@
dmas = <&pdma0 12
&pdma0 11>;
dma-names = "tx", "rx";
- clocks = <&clock 308>, <&clock 158>;
+ clocks = <&clock CLK_I2S2>, <&clock CLK_DIV_I2S2>;
clock-names = "iis", "i2s_opclk0";
pinctrl-names = "default";
pinctrl-0 = <&i2s2_bus>;
@@ -511,7 +513,7 @@
usb at 12000000 {
compatible = "samsung,exynos5250-dwusb3";
- clocks = <&clock 286>;
+ clocks = <&clock CLK_USB3>;
clock-names = "usbdrd30";
#address-cells = <1>;
#size-cells = <1>;
@@ -528,7 +530,7 @@
usb3_phy: usbphy at 12100000 {
compatible = "samsung,exynos5250-usb3phy";
reg = <0x12100000 0x100>;
- clocks = <&clock 1>, <&clock 286>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_USB3>;
clock-names = "ext_xtal", "usbdrd30";
#address-cells = <1>;
#size-cells = <1>;
@@ -544,7 +546,7 @@
reg = <0x12110000 0x100>;
interrupts = <0 71 0>;
- clocks = <&clock 285>;
+ clocks = <&clock CLK_USB2>;
clock-names = "usbhost";
};
@@ -553,14 +555,14 @@
reg = <0x12120000 0x100>;
interrupts = <0 71 0>;
- clocks = <&clock 285>;
+ clocks = <&clock CLK_USB2>;
clock-names = "usbhost";
};
usb2_phy: usbphy at 12130000 {
compatible = "samsung,exynos5250-usb2phy";
reg = <0x12130000 0x100>;
- clocks = <&clock 1>, <&clock 285>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_USB2>;
clock-names = "ext_xtal", "usbhost";
#address-cells = <1>;
#size-cells = <1>;
@@ -577,7 +579,7 @@
reg = <0x12dd0000 0x100>;
samsung,pwm-outputs = <0>, <1>, <2>, <3>;
#pwm-cells = <3>;
- clocks = <&clock 311>;
+ clocks = <&clock CLK_PWM>;
clock-names = "timers";
};
@@ -592,7 +594,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x121A0000 0x1000>;
interrupts = <0 34 0>;
- clocks = <&clock 275>;
+ clocks = <&clock CLK_PDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -603,7 +605,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x121B0000 0x1000>;
interrupts = <0 35 0>;
- clocks = <&clock 276>;
+ clocks = <&clock CLK_PDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -614,7 +616,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x10800000 0x1000>;
interrupts = <0 33 0>;
- clocks = <&clock 346>;
+ clocks = <&clock CLK_MDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -625,7 +627,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x11C10000 0x1000>;
interrupts = <0 124 0>;
- clocks = <&clock 271>;
+ clocks = <&clock CLK_MDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -638,7 +640,7 @@
reg = <0x13e00000 0x1000>;
interrupts = <0 85 0>;
samsung,power-domain = <&pd_gsc>;
- clocks = <&clock 256>;
+ clocks = <&clock CLK_GSCL0>;
clock-names = "gscl";
};
@@ -647,7 +649,7 @@
reg = <0x13e10000 0x1000>;
interrupts = <0 86 0>;
samsung,power-domain = <&pd_gsc>;
- clocks = <&clock 257>;
+ clocks = <&clock CLK_GSCL1>;
clock-names = "gscl";
};
@@ -656,7 +658,7 @@
reg = <0x13e20000 0x1000>;
interrupts = <0 87 0>;
samsung,power-domain = <&pd_gsc>;
- clocks = <&clock 258>;
+ clocks = <&clock CLK_GSCL2>;
clock-names = "gscl";
};
@@ -665,7 +667,7 @@
reg = <0x13e30000 0x1000>;
interrupts = <0 88 0>;
samsung,power-domain = <&pd_gsc>;
- clocks = <&clock 259>;
+ clocks = <&clock CLK_GSCL3>;
clock-names = "gscl";
};
@@ -673,8 +675,9 @@
compatible = "samsung,exynos4212-hdmi";
reg = <0x14530000 0x70000>;
interrupts = <0 95 0>;
- clocks = <&clock 344>, <&clock 136>, <&clock 137>,
- <&clock 159>, <&clock 1024>;
+ clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+ <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+ <&clock CLK_MOUT_HDMI>;
clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
"sclk_hdmiphy", "mout_hdmi";
};
@@ -683,7 +686,7 @@
compatible = "samsung,exynos5250-mixer";
reg = <0x14450000 0x10000>;
interrupts = <0 94 0>;
- clocks = <&clock 343>, <&clock 136>;
+ clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
clock-names = "mixer", "sclk_hdmi";
};
@@ -694,14 +697,14 @@
};
dp-controller at 145B0000 {
- clocks = <&clock 342>;
+ clocks = <&clock CLK_DP>;
clock-names = "dp";
phys = <&dp_phy>;
phy-names = "dp";
};
fimd at 14400000 {
- clocks = <&clock 133>, <&clock 339>;
+ clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
clock-names = "sclk_fimd", "fimd";
};
@@ -709,7 +712,7 @@
compatible = "samsung,exynos-adc-v1";
reg = <0x12D10000 0x100>, <0x10040718 0x4>;
interrupts = <0 106 0>;
- clocks = <&clock 303>;
+ clocks = <&clock CLK_ADC>;
clock-names = "adc";
#io-channel-cells = <1>;
io-channel-ranges;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH RESEND v2 3/4] ARM: dts: exynos5420: convert magic numbers to macros in clock bindings
2014-02-24 13:22 [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Andrzej Hajda
2014-02-24 13:22 ` [PATCH RESEND v2 1/4] ARM: dts: exynos4: convert magic numbers to macros in clock bindings Andrzej Hajda
2014-02-24 13:22 ` [PATCH RESEND v2 2/4] ARM: dts: exynos5250: " Andrzej Hajda
@ 2014-02-24 13:22 ` Andrzej Hajda
2014-02-24 13:23 ` [PATCH RESEND v2 4/4] ARM: dts: exynos5440: " Andrzej Hajda
2014-02-26 1:05 ` [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Kukjin Kim
4 siblings, 0 replies; 6+ messages in thread
From: Andrzej Hajda @ 2014-02-24 13:22 UTC (permalink / raw)
To: linux-arm-kernel
The patch replaces magic numbers with macros defined in DT header
in exynos5420 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung•com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung•com>
Acked-by: Tomasz Figa <t.figa@samsung•com>
Acked-by: Mike Turquette <mturquette@linaro•org>
---
.../devicetree/bindings/clock/exynos5420-clock.txt | 184 +--------------------
arch/arm/boot/dts/exynos5420.dtsi | 95 +++++------
2 files changed, 55 insertions(+), 224 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt
index 458f347..ca88c97 100644
--- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt
+++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt
@@ -13,184 +13,12 @@ Required Properties:
- #clock-cells: should be 1.
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
-
- [Core Clocks]
-
- Clock ID
- ----------------------------
-
- fin_pll 1
-
- [Clock Gate for Special Clocks]
-
- Clock ID
- ----------------------------
- sclk_uart0 128
- sclk_uart1 129
- sclk_uart2 130
- sclk_uart3 131
- sclk_mmc0 132
- sclk_mmc1 133
- sclk_mmc2 134
- sclk_spi0 135
- sclk_spi1 136
- sclk_spi2 137
- sclk_i2s1 138
- sclk_i2s2 139
- sclk_pcm1 140
- sclk_pcm2 141
- sclk_spdif 142
- sclk_hdmi 143
- sclk_pixel 144
- sclk_dp1 145
- sclk_mipi1 146
- sclk_fimd1 147
- sclk_maudio0 148
- sclk_maupcm0 149
- sclk_usbd300 150
- sclk_usbd301 151
- sclk_usbphy300 152
- sclk_usbphy301 153
- sclk_unipro 154
- sclk_pwm 155
- sclk_gscl_wa 156
- sclk_gscl_wb 157
- sclk_hdmiphy 158
-
- [Peripheral Clock Gates]
-
- Clock ID
- ----------------------------
-
- aclk66_peric 256
- uart0 257
- uart1 258
- uart2 259
- uart3 260
- i2c0 261
- i2c1 262
- i2c2 263
- i2c3 264
- i2c4 265
- i2c5 266
- i2c6 267
- i2c7 268
- i2c_hdmi 269
- tsadc 270
- spi0 271
- spi1 272
- spi2 273
- keyif 274
- i2s1 275
- i2s2 276
- pcm1 277
- pcm2 278
- pwm 279
- spdif 280
- i2c8 281
- i2c9 282
- i2c10 283
- aclk66_psgen 300
- chipid 301
- sysreg 302
- tzpc0 303
- tzpc1 304
- tzpc2 305
- tzpc3 306
- tzpc4 307
- tzpc5 308
- tzpc6 309
- tzpc7 310
- tzpc8 311
- tzpc9 312
- hdmi_cec 313
- seckey 314
- mct 315
- wdt 316
- rtc 317
- tmu 318
- tmu_gpu 319
- pclk66_gpio 330
- aclk200_fsys2 350
- mmc0 351
- mmc1 352
- mmc2 353
- sromc 354
- ufs 355
- aclk200_fsys 360
- tsi 361
- pdma0 362
- pdma1 363
- rtic 364
- usbh20 365
- usbd300 366
- usbd301 377
- aclk400_mscl 380
- mscl0 381
- mscl1 382
- mscl2 383
- smmu_mscl0 384
- smmu_mscl1 385
- smmu_mscl2 386
- aclk333 400
- mfc 401
- smmu_mfcl 402
- smmu_mfcr 403
- aclk200_disp1 410
- dsim1 411
- dp1 412
- hdmi 413
- aclk300_disp1 420
- fimd1 421
- smmu_fimd1 422
- aclk166 430
- mixer 431
- aclk266 440
- rotator 441
- mdma1 442
- smmu_rotator 443
- smmu_mdma1 444
- aclk300_jpeg 450
- jpeg 451
- jpeg2 452
- smmu_jpeg 453
- aclk300_gscl 460
- smmu_gscl0 461
- smmu_gscl1 462
- gscl_wa 463
- gscl_wb 464
- gscl0 465
- gscl1 466
- clk_3aa 467
- aclk266_g2d 470
- sss 471
- slim_sss 472
- mdma0 473
- aclk333_g2d 480
- g2d 481
- aclk333_432_gscl 490
- smmu_3aa 491
- smmu_fimcl0 492
- smmu_fimcl1 493
- smmu_fimcl3 494
- fimc_lite3 495
- aclk_g3d 500
- g3d 501
- smmu_mixer 502
-
- Mux ID
- ----------------------------
-
- mout_hdmi 640
-
- Divider ID
- ----------------------------
-
- dout_pixel 768
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5420.h header and can be used in device
+tree sources.
Example 1: An example of a clock controller node is listed below.
@@ -208,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
compatible = "samsung,exynos4210-uart";
reg = <0x13820000 0x100>;
interrupts = <0 54 0>;
- clocks = <&clock 259>, <&clock 130>;
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
clock-names = "uart", "clk_uart_baud0";
};
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index 45e2e65..e3329af 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -13,6 +13,7 @@
* published by the Free Software Foundation.
*/
+#include <dt-bindings/clock/exynos5420.h>
#include "exynos5.dtsi"
#include "exynos5420-pinctrl.dtsi"
@@ -119,7 +120,8 @@
compatible = "samsung,exynos5420-audss-clock";
reg = <0x03810000 0x0C>;
#clock-cells = <1>;
- clocks = <&clock 1>, <&clock 5>, <&clock 148>, <&clock 149>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+ <&clock CLK_SCLK_MAUDIO0>, <&clock CLK_SCLK_MAUPCM0>;
clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
};
@@ -127,7 +129,7 @@
compatible = "samsung,mfc-v7";
reg = <0x11000000 0x10000>;
interrupts = <0 96 0>;
- clocks = <&clock 401>;
+ clocks = <&clock CLK_MFC>;
clock-names = "mfc";
};
@@ -137,7 +139,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12200000 0x2000>;
- clocks = <&clock 351>, <&clock 132>;
+ clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>;
clock-names = "biu", "ciu";
fifo-depth = <0x40>;
status = "disabled";
@@ -149,7 +151,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12210000 0x2000>;
- clocks = <&clock 352>, <&clock 133>;
+ clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>;
clock-names = "biu", "ciu";
fifo-depth = <0x40>;
status = "disabled";
@@ -161,7 +163,7 @@
#address-cells = <1>;
#size-cells = <0>;
reg = <0x12220000 0x1000>;
- clocks = <&clock 353>, <&clock 134>;
+ clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>;
clock-names = "biu", "ciu";
fifo-depth = <0x40>;
status = "disabled";
@@ -175,7 +177,7 @@
interrupt-parent = <&mct_map>;
interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>,
<8>, <9>, <10>, <11>;
- clocks = <&clock 1>, <&clock 315>;
+ clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
clock-names = "fin_pll", "mct";
mct_map: mct-map {
@@ -269,7 +271,7 @@
};
rtc at 101E0000 {
- clocks = <&clock 317>;
+ clocks = <&clock CLK_RTC>;
clock-names = "rtc";
status = "disabled";
};
@@ -296,7 +298,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x121A0000 0x1000>;
interrupts = <0 34 0>;
- clocks = <&clock 362>;
+ clocks = <&clock CLK_PDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -307,7 +309,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x121B0000 0x1000>;
interrupts = <0 35 0>;
- clocks = <&clock 363>;
+ clocks = <&clock CLK_PDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -318,7 +320,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x10800000 0x1000>;
interrupts = <0 33 0>;
- clocks = <&clock 473>;
+ clocks = <&clock CLK_MDMA0>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -329,7 +331,7 @@
compatible = "arm,pl330", "arm,primecell";
reg = <0x11C10000 0x1000>;
interrupts = <0 124 0>;
- clocks = <&clock 442>;
+ clocks = <&clock CLK_MDMA1>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
@@ -360,7 +362,7 @@
dmas = <&pdma1 12
&pdma1 11>;
dma-names = "tx", "rx";
- clocks = <&clock 275>, <&clock 138>;
+ clocks = <&clock CLK_I2S1>, <&clock CLK_SCLK_I2S1>;
clock-names = "iis", "i2s_opclk0";
pinctrl-names = "default";
pinctrl-0 = <&i2s1_bus>;
@@ -373,7 +375,7 @@
dmas = <&pdma0 12
&pdma0 11>;
dma-names = "tx", "rx";
- clocks = <&clock 276>, <&clock 139>;
+ clocks = <&clock CLK_I2S2>, <&clock CLK_SCLK_I2S2>;
clock-names = "iis", "i2s_opclk0";
pinctrl-names = "default";
pinctrl-0 = <&i2s2_bus>;
@@ -391,7 +393,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&spi0_bus>;
- clocks = <&clock 271>, <&clock 135>;
+ clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
clock-names = "spi", "spi_busclk0";
status = "disabled";
};
@@ -407,7 +409,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&spi1_bus>;
- clocks = <&clock 272>, <&clock 136>;
+ clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
clock-names = "spi", "spi_busclk0";
status = "disabled";
};
@@ -423,28 +425,28 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&spi2_bus>;
- clocks = <&clock 273>, <&clock 137>;
+ clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
clock-names = "spi", "spi_busclk0";
status = "disabled";
};
serial at 12C00000 {
- clocks = <&clock 257>, <&clock 128>;
+ clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
clock-names = "uart", "clk_uart_baud0";
};
serial at 12C10000 {
- clocks = <&clock 258>, <&clock 129>;
+ clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
clock-names = "uart", "clk_uart_baud0";
};
serial at 12C20000 {
- clocks = <&clock 259>, <&clock 130>;
+ clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
clock-names = "uart", "clk_uart_baud0";
};
serial at 12C30000 {
- clocks = <&clock 260>, <&clock 131>;
+ clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
clock-names = "uart", "clk_uart_baud0";
};
@@ -453,7 +455,7 @@
reg = <0x12dd0000 0x100>;
samsung,pwm-outputs = <0>, <1>, <2>, <3>;
#pwm-cells = <3>;
- clocks = <&clock 279>;
+ clocks = <&clock CLK_PWM>;
clock-names = "timers";
};
@@ -464,7 +466,7 @@
};
dp-controller at 145B0000 {
- clocks = <&clock 412>;
+ clocks = <&clock CLK_DP1>;
clock-names = "dp";
phys = <&dp_phy>;
phy-names = "dp";
@@ -472,7 +474,7 @@
fimd at 14400000 {
samsung,power-domain = <&disp_pd>;
- clocks = <&clock 147>, <&clock 421>;
+ clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
clock-names = "sclk_fimd", "fimd";
};
@@ -480,7 +482,7 @@
compatible = "samsung,exynos-adc-v2";
reg = <0x12D10000 0x100>, <0x10040720 0x4>;
interrupts = <0 106 0>;
- clocks = <&clock 270>;
+ clocks = <&clock CLK_TSADC>;
clock-names = "adc";
#io-channel-cells = <1>;
io-channel-ranges;
@@ -493,7 +495,7 @@
interrupts = <0 56 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 261>;
+ clocks = <&clock CLK_I2C0>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_bus>;
@@ -506,7 +508,7 @@
interrupts = <0 57 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 262>;
+ clocks = <&clock CLK_I2C1>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_bus>;
@@ -519,7 +521,7 @@
interrupts = <0 58 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 263>;
+ clocks = <&clock CLK_I2C2>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c2_bus>;
@@ -532,7 +534,7 @@
interrupts = <0 59 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 264>;
+ clocks = <&clock CLK_I2C3>;
clock-names = "i2c";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_bus>;
@@ -547,7 +549,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c4_hs_bus>;
- clocks = <&clock 265>;
+ clocks = <&clock CLK_I2C4>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -560,7 +562,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c5_hs_bus>;
- clocks = <&clock 266>;
+ clocks = <&clock CLK_I2C5>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -573,7 +575,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c6_hs_bus>;
- clocks = <&clock 267>;
+ clocks = <&clock CLK_I2C6>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -586,7 +588,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c7_hs_bus>;
- clocks = <&clock 268>;
+ clocks = <&clock CLK_I2C7>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -599,7 +601,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c8_hs_bus>;
- clocks = <&clock 281>;
+ clocks = <&clock CLK_I2C8>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -612,7 +614,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c9_hs_bus>;
- clocks = <&clock 282>;
+ clocks = <&clock CLK_I2C9>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -625,7 +627,7 @@
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c10_hs_bus>;
- clocks = <&clock 283>;
+ clocks = <&clock CLK_I2C10>;
clock-names = "hsi2c";
status = "disabled";
};
@@ -634,8 +636,9 @@
compatible = "samsung,exynos4212-hdmi";
reg = <0x14530000 0x70000>;
interrupts = <0 95 0>;
- clocks = <&clock 413>, <&clock 143>, <&clock 768>,
- <&clock 158>, <&clock 640>;
+ clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+ <&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+ <&clock CLK_MOUT_HDMI>;
clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
"sclk_hdmiphy", "mout_hdmi";
status = "disabled";
@@ -645,7 +648,7 @@
compatible = "samsung,exynos5420-mixer";
reg = <0x14450000 0x10000>;
interrupts = <0 94 0>;
- clocks = <&clock 431>, <&clock 143>;
+ clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
clock-names = "mixer", "sclk_hdmi";
};
@@ -653,7 +656,7 @@
compatible = "samsung,exynos5-gsc";
reg = <0x13e00000 0x1000>;
interrupts = <0 85 0>;
- clocks = <&clock 465>;
+ clocks = <&clock CLK_GSCL0>;
clock-names = "gscl";
samsung,power-domain = <&gsc_pd>;
};
@@ -662,7 +665,7 @@
compatible = "samsung,exynos5-gsc";
reg = <0x13e10000 0x1000>;
interrupts = <0 86 0>;
- clocks = <&clock 466>;
+ clocks = <&clock CLK_GSCL1>;
clock-names = "gscl";
samsung,power-domain = <&gsc_pd>;
};
@@ -676,7 +679,7 @@
compatible = "samsung,exynos5420-tmu";
reg = <0x10060000 0x100>;
interrupts = <0 65 0>;
- clocks = <&clock 318>;
+ clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
};
@@ -684,7 +687,7 @@
compatible = "samsung,exynos5420-tmu";
reg = <0x10064000 0x100>;
interrupts = <0 183 0>;
- clocks = <&clock 318>;
+ clocks = <&clock CLK_TMU>;
clock-names = "tmu_apbif";
};
@@ -692,7 +695,7 @@
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x10068000 0x100>, <0x1006c000 0x4>;
interrupts = <0 184 0>;
- clocks = <&clock 318>, <&clock 318>;
+ clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
};
@@ -700,7 +703,7 @@
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x1006c000 0x100>, <0x100a0000 0x4>;
interrupts = <0 185 0>;
- clocks = <&clock 318>, <&clock 319>;
+ clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
};
@@ -708,7 +711,7 @@
compatible = "samsung,exynos5420-tmu-ext-triminfo";
reg = <0x100a0000 0x100>, <0x10068000 0x4>;
interrupts = <0 215 0>;
- clocks = <&clock 319>, <&clock 318>;
+ clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
clock-names = "tmu_apbif", "tmu_triminfo_apbif";
};
@@ -716,7 +719,7 @@
compatible = "samsung,exynos5420-wdt";
reg = <0x101D0000 0x100>;
interrupts = <0 42 0>;
- clocks = <&clock 316>;
+ clocks = <&clock CLK_WDT>;
clock-names = "watchdog";
samsung,syscon-phandle = <&pmu_system_controller>;
};
--
1.8.3.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH RESEND v2 4/4] ARM: dts: exynos5440: convert magic numbers to macros in clock bindings
2014-02-24 13:22 [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Andrzej Hajda
` (2 preceding siblings ...)
2014-02-24 13:22 ` [PATCH RESEND v2 3/4] ARM: dts: exynos5420: " Andrzej Hajda
@ 2014-02-24 13:23 ` Andrzej Hajda
2014-02-26 1:05 ` [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Kukjin Kim
4 siblings, 0 replies; 6+ messages in thread
From: Andrzej Hajda @ 2014-02-24 13:23 UTC (permalink / raw)
To: linux-arm-kernel
The patch replaces magic numbers with macros defined in DT header
in exynos5440 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung•com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung•com>
Acked-by: Tomasz Figa <t.figa@samsung•com>
Acked-by: Mike Turquette <mturquette@linaro•org>
---
.../devicetree/bindings/clock/exynos5440-clock.txt | 45 +++-------------------
arch/arm/boot/dts/exynos5440.dtsi | 33 ++++++++--------
2 files changed, 23 insertions(+), 55 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt
index 9955dc9..5f7005f 100644
--- a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt
+++ b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt
@@ -12,45 +12,12 @@ Required Properties:
- #clock-cells: should be 1.
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
-
-
- [Core Clocks]
-
- Clock ID
- ----------------------------
-
- xtal 1
- arm_clk 2
-
- [Peripheral Clock Gates]
-
- Clock ID
- ----------------------------
-
- spi_baud 16
- pb0_250 17
- pr0_250 18
- pr1_250 19
- b_250 20
- b_125 21
- b_200 22
- sata 23
- usb 24
- gmac0 25
- cs250 26
- pb0_250_o 27
- pr0_250_o 28
- pr1_250_o 29
- b_250_o 30
- b_125_o 31
- b_200_o 32
- sata_o 33
- usb_o 34
- gmac0_o 35
- cs250_o 36
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5440.h header and can be used in device
+tree sources.
Example: An example of a clock controller node is listed below.
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index 02a0a12..75c7b89 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -9,6 +9,7 @@
* published by the Free Software Foundation.
*/
+#include <dt-bindings/clock/exynos5440.h>
#include "skeleton.dtsi"
/ {
@@ -105,7 +106,7 @@
compatible = "samsung,exynos4210-uart";
reg = <0xB0000 0x1000>;
interrupts = <0 2 0>;
- clocks = <&clock 21>, <&clock 21>;
+ clocks = <&clock CLK_B_125>, <&clock CLK_B_125>;
clock-names = "uart", "clk_uart_baud0";
};
@@ -113,7 +114,7 @@
compatible = "samsung,exynos4210-uart";
reg = <0xC0000 0x1000>;
interrupts = <0 3 0>;
- clocks = <&clock 21>, <&clock 21>;
+ clocks = <&clock CLK_B_125>, <&clock CLK_B_125>;
clock-names = "uart", "clk_uart_baud0";
};
@@ -125,7 +126,7 @@
#size-cells = <0>;
samsung,spi-src-clk = <0>;
num-cs = <1>;
- clocks = <&clock 21>, <&clock 16>;
+ clocks = <&clock CLK_B_125>, <&clock CLK_SPI_BAUD>;
clock-names = "spi", "spi_busclk0";
};
@@ -161,7 +162,7 @@
interrupts = <0 5 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "i2c";
};
@@ -171,7 +172,7 @@
interrupts = <0 6 0>;
#address-cells = <1>;
#size-cells = <0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "i2c";
};
@@ -179,7 +180,7 @@
compatible = "samsung,s3c2410-wdt";
reg = <0x110000 0x1000>;
interrupts = <0 1 0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "watchdog";
};
@@ -190,7 +191,7 @@
interrupts = <0 31 4>;
interrupt-names = "macirq";
phy-mode = "sgmii";
- clocks = <&clock 25>;
+ clocks = <&clock CLK_GMAC0>;
clock-names = "stmmaceth";
};
@@ -206,7 +207,7 @@
compatible = "samsung,s3c6410-rtc";
reg = <0x130000 0x1000>;
interrupts = <0 17 0>, <0 16 0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "rtc";
};
@@ -214,7 +215,7 @@
compatible = "samsung,exynos5440-tmu";
reg = <0x160118 0x230>, <0x160368 0x10>;
interrupts = <0 58 0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "tmu_apbif";
};
@@ -222,7 +223,7 @@
compatible = "samsung,exynos5440-tmu";
reg = <0x16011C 0x230>, <0x160368 0x10>;
interrupts = <0 58 0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "tmu_apbif";
};
@@ -230,7 +231,7 @@
compatible = "samsung,exynos5440-tmu";
reg = <0x160120 0x230>, <0x160368 0x10>;
interrupts = <0 58 0>;
- clocks = <&clock 21>;
+ clocks = <&clock CLK_B_125>;
clock-names = "tmu_apbif";
};
@@ -238,7 +239,7 @@
compatible = "snps,exynos5440-ahci";
reg = <0x210000 0x10000>;
interrupts = <0 30 0>;
- clocks = <&clock 23>;
+ clocks = <&clock CLK_SATA>;
clock-names = "sata";
};
@@ -246,7 +247,7 @@
compatible = "samsung,exynos5440-ohci";
reg = <0x220000 0x1000>;
interrupts = <0 29 0>;
- clocks = <&clock 24>;
+ clocks = <&clock CLK_USB>;
clock-names = "usbhost";
};
@@ -254,7 +255,7 @@
compatible = "samsung,exynos5440-ehci";
reg = <0x221000 0x1000>;
interrupts = <0 29 0>;
- clocks = <&clock 24>;
+ clocks = <&clock CLK_USB>;
clock-names = "usbhost";
};
@@ -264,7 +265,7 @@
0x270000 0x1000
0x271000 0x40>;
interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
- clocks = <&clock 28>, <&clock 27>;
+ clocks = <&clock CLK_PR0_250_O>, <&clock CLK_PB0_250_O>;
clock-names = "pcie", "pcie_bus";
#address-cells = <3>;
#size-cells = <2>;
@@ -285,7 +286,7 @@
0x272000 0x1000
0x271040 0x40>;
interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
- clocks = <&clock 29>, <&clock 27>;
+ clocks = <&clock CLK_PR1_250_O>, <&clock CLK_PB0_250_O>;
clock-names = "pcie", "pcie_bus";
#address-cells = <3>;
#size-cells = <2>;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros
2014-02-24 13:22 [PATCH RESEND v2 0/4] clk/exynos convert clock IDs to macros Andrzej Hajda
` (3 preceding siblings ...)
2014-02-24 13:23 ` [PATCH RESEND v2 4/4] ARM: dts: exynos5440: " Andrzej Hajda
@ 2014-02-26 1:05 ` Kukjin Kim
4 siblings, 0 replies; 6+ messages in thread
From: Kukjin Kim @ 2014-02-26 1:05 UTC (permalink / raw)
To: linux-arm-kernel
On 02/24/14 22:22, Andrzej Hajda wrote:
> Hi,
>
Hi Andrzej,
> This patch set converts dts files to use macros instead
> of magic numbers or enums to describe clock bindings.
>
> The patch set is rebased on the latest kgene/for-next branch.
>
Thanks.
> The patches are generated by script.
> Many clocks I have verified by hand.
> I have also tested it successfully on exynos4 based board.
>
:)
> This is the 2nd version of the patchset.
> Changes:
> - corrected devicetree mailing list,
> - added comments to include/dt-bindings/clock/exynos4.h for
> clocks present only in particular chip,
> - added tab alignement in headers,
> - added comment to CLK_NR_CLKS,
> - added copyright headers,
> - split long lines in dts,
> - corrected example in bindings/clock/exynos5250-clock.txt, to point
> appropriate clocks.
>
> Regards
> Andrzej
>
> Andrzej Hajda (4):
> ARM: dts: exynos4: convert magic numbers to macros in clock bindings
> ARM: dts: exynos5250: convert magic numbers to macros in clock
> bindings
> ARM: dts: exynos5420: convert magic numbers to macros in clock
> bindings
> ARM: dts: exynos5440: convert magic numbers to macros in clock
> bindings
>
> .../devicetree/bindings/clock/exynos4-clock.txt | 259 +--------------------
> .../devicetree/bindings/clock/exynos5250-clock.txt | 163 +------------
> .../devicetree/bindings/clock/exynos5420-clock.txt | 184 +--------------
> .../devicetree/bindings/clock/exynos5440-clock.txt | 45 +---
> arch/arm/boot/dts/exynos4.dtsi | 73 +++---
> arch/arm/boot/dts/exynos4210.dtsi | 9 +-
> arch/arm/boot/dts/exynos4x12.dtsi | 34 +--
> arch/arm/boot/dts/exynos5250.dtsi | 105 +++++----
> arch/arm/boot/dts/exynos5420.dtsi | 95 ++++----
> arch/arm/boot/dts/exynos5440.dtsi | 33 +--
> 10 files changed, 207 insertions(+), 793 deletions(-)
>
Looks good to me, applied.
Thanks,
Kukjin
^ permalink raw reply [flat|nested] 6+ messages in thread