From: Bartlomiej Sieka <tur@semihalf•com>
To: Grant Likely <grant.likely@secretlab•ca>
Cc: linuxppc-dev@ozlabs•org, Anatolij Gustschin <agust@denx•de>,
Paul Mackerras <paulus@samba•org>
Subject: [RESEND][POWERPC] mpc5200: Amalgamated dts fixes and updates
Date: Wed, 26 Mar 2008 20:45:27 +0100 [thread overview]
Message-ID: <20080326194526.GA17424@frozen.semihalf.com> (raw)
In-Reply-To: <fa686aa40803212014ne560615sfcdef542d59eb6cb@mail.gmail.com>
The bulk of this patch is taken from
http://patchwork.ozlabs.org/linuxppc/patch?q=Balakowicz&id=16197, with few
other updates.
Signed-off-by: Marian Balakowicz <m8@semihalf•com>
---
Addressed comments from the list; would appreciate picking up as the patch
fixes booting issue on TQM5200 and Motion-PRO (cm5200 changes are analogous,
but not tested due to hardware unavailability).
diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index 30737ea..2d25ca8 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -212,13 +212,30 @@
ethernet@3000 {
device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
- reg = <3000 800>;
+ reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+ reg = <3000 400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+ interrupt-parent = <&mpc5200_pic>;
+
+ phy0:ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
};
i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
@@ -231,4 +248,22 @@
reg = <8000 4000>;
};
};
+
+ lpb {
+ model = "fsl,lpb";
+ compatible = "fsl,lpb";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 fc000000 2000000>;
+
+ // 16-bit flash device at LocalPlus Bus CS0
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 2000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+ };
+ };
};
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index 76951ab..f27256b 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -148,7 +148,6 @@
interrupt-parent = <&mpc5200_pic>;
};
-
spi@f00 {
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
reg = <f00 20>;
@@ -209,10 +208,25 @@
ethernet@3000 {
device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
- reg = <3000 800>;
+ reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+ reg = <3000 400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+ interrupt-parent = <&mpc5200_pic>;
+
+ phy0:ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <2>;
+ };
};
ata@3a00 {
@@ -223,11 +237,19 @@
};
i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
+
+ rtc@68 {
+ device_type = "rtc";
+ compatible = "dallas,ds1339";
+ reg = <68>;
+ };
};
sram@8000 {
@@ -240,7 +262,8 @@
compatible = "fsl,lpb";
#address-cells = <2>;
#size-cells = <1>;
- ranges = <1 0 50000000 00010000
+ ranges = <0 0 ff000000 01000000
+ 1 0 50000000 00010000
2 0 50010000 00010000
3 0 50020000 00010000>;
@@ -271,31 +294,15 @@
compatible = "promess,pro_module_dio";
reg = <3 800 2>;
};
- };
- pci@f0000d00 {
- #interrupt-cells = <1>;
- #size-cells = <2>;
- #address-cells = <3>;
- device_type = "pci";
- compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
- reg = <f0000d00 100>;
- interrupt-map-mask = <f800 0 0 7>;
- interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
- c000 0 0 2 &mpc5200_pic 1 1 3
- c000 0 0 3 &mpc5200_pic 1 2 3
- c000 0 0 4 &mpc5200_pic 1 3 3
-
- c800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
- c800 0 0 2 &mpc5200_pic 1 2 3
- c800 0 0 3 &mpc5200_pic 1 3 3
- c800 0 0 4 &mpc5200_pic 0 0 3>;
- clock-frequency = <0>; // From boot loader
- interrupts = <2 8 0 2 9 0 2 a 0>;
- interrupt-parent = <&mpc5200_pic>;
- bus-range = <0 0>;
- ranges = <42000000 0 80000000 80000000 0 20000000
- 02000000 0 a0000000 a0000000 0 10000000
- 01000000 0 00000000 b0000000 0 01000000>;
+ // 16-bit flash device at LocalPlus Bus CS0
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 01000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+ };
};
};
diff --git a/arch/powerpc/boot/dts/tqm5200.dts b/arch/powerpc/boot/dts/tqm5200.dts
index c86464f..d2dc278 100644
--- a/arch/powerpc/boot/dts/tqm5200.dts
+++ b/arch/powerpc/boot/dts/tqm5200.dts
@@ -127,10 +127,25 @@
ethernet@3000 {
device_type = "network";
compatible = "fsl,mpc5200-fec";
- reg = <3000 800>;
+ reg = <3000 400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
interrupt-parent = <&mpc5200_pic>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+ reg = <3000 400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+ interrupt-parent = <&mpc5200_pic>;
+
+ phy0:ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ };
};
ata@3a00 {
@@ -141,11 +156,19 @@
};
i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,mpc5200-i2c","fsl-i2c";
reg = <3d40 40>;
interrupts = <2 10 0>;
interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
+
+ rtc@68 {
+ device_type = "rtc";
+ compatible = "dallas,ds1307";
+ reg = <68>;
+ };
};
sram@8000 {
@@ -154,6 +177,23 @@
};
};
+ lpb {
+ model = "fsl,lpb";
+ compatible = "fsl,lpb";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 fc000000 02000000>;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 02000000>;
+ bank-width = <4>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+ };
+ };
+
pci@f0000d00 {
#interrupt-cells = <1>;
#size-cells = <2>;
next prev parent reply other threads:[~2008-03-26 19:34 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-03-20 14:18 Oops with TQM5200 on TQM5200 Wolfgang Grandegger
2008-03-20 14:41 ` Grant Likely
2008-03-20 15:24 ` Anatolij Gustschin
2008-03-20 16:17 ` Bartlomiej Sieka
2008-03-20 21:27 ` Grant Likely
2008-03-22 10:49 ` Anatolij Gustschin
2008-03-22 14:39 ` Grant Likely
2008-03-20 16:29 ` Wolfgang Grandegger
2008-03-20 23:50 ` Grant Likely
2008-03-21 0:07 ` Bartlomiej Sieka
2008-03-21 0:20 ` Grant Likely
2008-03-21 23:56 ` [POWERPC] mpc52xx: Amalgamated dts fixes and updates Bartlomiej Sieka
2008-03-22 0:12 ` David Gibson
2008-03-22 3:47 ` Grant Likely
2008-03-22 0:41 ` Anatolij Gustschin
2008-03-22 3:14 ` Grant Likely
2008-03-26 19:45 ` Bartlomiej Sieka [this message]
2008-03-26 20:35 ` [RESEND][POWERPC] mpc5200: " Grant Likely
2008-03-26 20:48 ` Wolfgang Grandegger
2008-03-26 21:32 ` Bartlomiej Sieka
2008-03-26 21:18 ` [RESEND2][POWERPC] " Bartlomiej Sieka
2008-03-26 21:02 ` [RESEND][POWERPC] " Matt Sealey
2008-03-26 21:16 ` Grant Likely
2008-03-26 22:51 ` David Gibson
2008-03-26 22:57 ` Matt Sealey
2008-03-26 23:28 ` David Gibson
2008-03-24 16:59 ` [POWERPC] mpc52xx: " Wolfgang Grandegger
2008-03-21 6:30 ` Oops with TQM5200 on TQM5200 Wolfgang Grandegger
2008-03-21 19:02 ` Grant Likely
2008-03-24 6:47 ` Paul Mackerras
2008-03-25 9:54 ` Wolfgang Grandegger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080326194526.GA17424@frozen.semihalf.com \
--to=tur@semihalf$(echo .)com \
--cc=agust@denx$(echo .)de \
--cc=grant.likely@secretlab$(echo .)ca \
--cc=linuxppc-dev@ozlabs$(echo .)org \
--cc=paulus@samba$(echo .)org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox